Automatic Operation; Hi-Power Operation; Remote Control - Toshiba R32 Owner's Manual

1 INDOOR UNIT DISPLAY
1 ECO (White)
2 Wi-Fi access (White) w
3 Hi-Power (White)
4 Timer (White)
5 Operation mode
- Cool (Blue)
- Heat (Orange)
● Display brightness can be adjusted, follow procedure on (.
w Require Wireless LAN connecting adapter which available as accessory.
2 PREPARATION BEFORE USE
Preparing Filters
1. Open the air inlet grille and remove the air fi lters.
2. Attach the fi lters. (see detail in the accessory sheet).
Loading Batteries (when use wireless operation.)
1. Remove the slide cover.
2. Insert 2 new batteries (AAA type)
following the (+) and (–) positions.
Clock Setup
1. Push by tip of the pencil.
If timer indication is fl ashing, go to the next step 2.
2. Press or : adjust the time.
3. Press : Set the time.
Remote Control Reset
Push by tip of the pencil or
1. Remove the batteries.
2. Press .
3. Insert the batteries.
3 AIR FLOW DIRECTION
1
Press : Move the louver in
the desired vertical direction.
2
Press : Swing the air
automatically and press again to stop.
For horizontal direction, adjust
3
manually.
Note:
● Do not move the louver manually by others.
● The louver may automation positioning by some operation mode.
4

REMOTE CONTROL

1 Infrared signal emitter
2 Memory and Preset button (PRESET)
Start/Stop button
3
Mode select button (MODE)
4
Air fl ow/HADA CARE FLOW button
5
6 Fireplace/8°C button
ECO button
7
Comfort sleep button (COMFORT SLEEP)
8
Weekly timer (ON/OFF)
9
! Temp for Weekly timer
" On timer button (ON)
Set clock button (CLOCK)
#
Check button (CHECK)
$
% Filter reset button (FILTER)
& Temperature button (TEMP)
Swing louver button (SWING)
(
Fan speed button (FAN)
)
Set louver button (FIX)
~
+ High power button (Hi-POWER)
Power selection/Silent button (P-SEL/SILENT)
,
Program P1 - P4
-
Day/Edit button
.
/ Setup button (SET)
: Off timer button (OFF)
Clear button (CLR)
;
Reset button (RESET)
<
Note:
● The provided Remote Controller is a wireless type, which also can be
used as a wire. Please see "How to Connect The Remote Controller
for Wired Operation", located in installation instruction, in case of wired
control is required.
● In wire operation, remote controller will return to initial condition
(PRESET, TIMER and CLOCK will return to initial condition) when user
shutdown power supply of Air conditioner.
1
2
&
3
(
4
)
5
6
~
7
+
8
,
9
-
!
.
" /
#
:
$
;
%
<
5 COOLING / HEATING / FAN ONLY OPERATION
1. Press : Select Cool
2. Press : Set the desired temperature. Min. 17°C, Max. 30°C.
Fan Only: No temperature indication
3. Press : Select AUTO, LOW , LOW+
MED+ , HIGH
6

AUTOMATIC OPERATION

To automatically select cooling, heating or fan only operation
1. Press : Select Auto A.
2. Press : Set the desired temperature. Min. 17°C, Max. 30°C.
3. Press : Select AUTO, LOW , LOW+
MED+ , HIGH
7 DRY OPERATION
For dehumidifi cation, a moderate cooling performance is controlled
automatically.
1. Press : Select Dry
2. Press : Set the desired temperature. Min. 17°C, Max. 30°C.
Note : DRY mode fan speed is set to Auto only.
8

Hi-POWER OPERATION

To automatically control room temperature and airfl ow for faster cooling or
heating operation (except in DRY and FAN ONLY mode)
Press : Start and stop the operation.
9 ECO OPERATION
To automatically control room temperature to save energy (except in DRY
and FAN ONLY mode)
Press : Start and stop the operation.
Note : Cooling operation; the set temperture will increase automatically
1 degree/hour for 2 hours (maximum 2 degrees increase).
For heating operation the set temperture will decrease.
10 FIREPLACE AND 8°C HEATING OPERATION
Fireplace Operation ( )
Keep indoor unit's fan blowing continuously during thermo off, to circulate heat
from other sources over the room. There are three setting parameters: Default
setting > Fireplace 1 > Fireplace 2
Fireplace 1:
During thermo off period, the indoor unit's fan will continue to run by the same
speed, previously selected by end-user.
Fireplace 2:
During thermo off period, the indoor unit's fan will continue to run at super-low
speed, programmed from factory.
8°C Heating Operation (8°C)
Heat mode operation for keep room temperature (5-13°C) with less of energy
usage.
Fireplace and 8°C Heating Operation
FIREPLACE 1
Note:
● While Fireplace operation on heating mode, indoor unit fan always runs
and cold air breezing might be occurred.
● Fireplace and 8°C will operate in Heating mode only.
, Heat or Fan only .
, MED ,
or QUIET
, MED ,
or QUIET
.
8°C
FIREPLACE 2
Normal
operation