Related Manuals for Timberwolf TW230DHB
Summary of Contents for Timberwolf TW230DHB
-
Page 1: Table Of Contents
TIMBERWOLF CONTENTS TW 230DHB Section Page No. INTRODUCTION PURPOSE OF MACHINE MACHINE DIMENSIONS & SPECIFICATIONS PARTS LOCATION DIAGRAMS SAFE WORKING Operator’s Personal Protective Equipment Required Basic Woodchipping Safety General Safety Matters - Do’s and Dont’s Noise Test OPERATING INSTRUCTIONS Safe Transportation... -
Page 2: Introduction
Timberwolf's policy of regularly reviewing and improving their products may involve major or minor changes to the chippers or their accessories. Timberwolf reserves the right to make changes at any time without notice and without incurring any obligation. -
Page 3: Purpose Of Machine
TIMBERWOLF TW 230DHB The Timberwolf TW 230DHB Designed to chip solid wood material up to 160mm in diameter and capable of chipping over 5 tonnes of brushwood per hour. DIMENSIONS Serial No. Location The serial number can be found identification plate located on the chassis beam. - Page 4 Serial No. Location The serial number can be found on the identification plate located on the chassis beam. 3500mm (tray up) 3905mm (tray down) TIMBERWOLF TW 230DH(a) (ADJUSTABLE TOWHEAD) SPECIFICATION Engine type: Maximum diameter material: Kubota 4-cylinder diesel 160mm (6 ⁄...
-
Page 5: Parts Location Diagrams
TIMBERWOLF TW 230DHB PARTS LOCATOR FUNNEL DISCHARGE SAFETY BAR MANUAL CONTROL BOX TUBE CANNISTER (each side) FEED TRAY DISCHARGE BUCKET CLAMP NUTS AIR FILTER HEAD LIGHT BOARD REFLECTOR ACCESS HATCH PROP STAND SIDE PANELS RAIN FLAP ROTOR HOUSING REFLECTORS... - Page 6 TIMBERWOLF TW 230DHB PARTS LOCATOR ELECTRICAL ROLLER PANEL BOX GUARD CONTROL EXHAUST PANEL ENGINE BLOCK FUEL TANK RADIATOR jOCKEY WHEEL ASSEMBLY FUEL HYDRAULIC PUMP HYDRAULIC FUEL TANK FILTER PUMP BELT TENSION IN-LINE ADjUSTER FUEL FILTER FAN SECTION (x4) ROTOR ROTOR...
-
Page 7: Safe Working
TIMBERWOLF SAFE WORKING TW 230DHB WARNING The chipper will feed material through on its own. To do this, it relies on sharp blades both on the feed rollers and the chipper rotor. To keep the blades sharp, only feed the machine with clean brushwood. DO NOT put muddy/dirty wood, roots, potted plants, bricks, stones or metal into the chipper. -
Page 8: General Safety Matters - Do's And Dont's
SAFE WORKING TIMBERWOLF ü TW 230DHB GENERAL SAFETY MATTERS D O ’ S A N D D O N ’ T S ALWAYS stop the chipper engine before making DO NOT operate chipper unless available light is any adjustments, refuelling or cleaning. -
Page 9: Noise Test
TIMBERWOLF SAFE WORKING TW 230DHB NOISE TEST MACHINE: TW 230DHB NOTES: Tested chipping 120mm x 120mm corsican pine 1.5m in length Noise levels above 80dB (A) will be experienced at the working position. Wear ear protection at all times to prevent possible damage to hearing. All persons within a 4 metre radius must also wear good quality ear protection. -
Page 10: Operating Instructions
OPERATING INSTRUCTIONS TIMBERWOLF TW 230DHB DO NOT RIDE ON THE CHIPPER WHEN IT IS SAFE TRANSPORTATION WARNING BEING TOWED. WHEN towing a chipper the maximum speed limit • is 60 mph. WHEN reversing the chipper the short wheel base •... -
Page 11: Delivery
TW 230DHB DELIVERY All Timberwolf TW 230DHB machines have a full pre - delivery inspection before leaving the factory and are ready to use. Read and understand this instruction manual before attempting to operate the chipper. In particular, read pages 6-8 which contain important health and safety information and advice. -
Page 12: Auto Controls
‘slow’ (idle) position. BLADE WEAR The most important part of using a wood chipper is keeping the cutter blades sharp. Timberwolf chipper blades are hollow ground to an angle of 40 degrees. When performing daily blade checks ensure blade edge is sharp and free from chips, if there is any evidence of damage, or the edge is “dull”... -
Page 13: Before Using The Chipper
TIMBERWOLF OPERATING INSTRUCTIONS TW 230DHB BEFORE USING THE CHIPPER WITH THE ENGINE RUNNING AT FULL SPEED PRESS THE GREEN PRESS THE RED PRESS THE BLUE BUTTON SAFETY BAR BUTTON THE IN-FEED SHOULD TURN THE IN-FEED THE IN-FEED BACKWARDS ONLY WHILE THE... -
Page 14: Starting To Chip
OPERATING INSTRUCTIONS TIMBERWOLF TW 230DHB STARTING TO CHIP Do not use or attempt to start the chipper without the protective guarding and discharge unit securely in place. Failure to do so may WARNING result in personal injury or loss of life CHECK that the chipper is running smoothly. -
Page 15: Service Instructions
MAINTENANCE THAT SHOULD BE APPLIED TO ANY PIECE OF MECHANICAL EQUIPMENT AND THE CHASSIS TO WHICH IT IS MOUNTED. AUTHORISED TIMBERWOLF SERvICE AGENTS ARE FULLY TRAINED IN ALL ASPECTS OF TOTAL SERvICE AND MAINTENANCE OF TIMBERWOLF WOOD CHIPPERS. YOU ARE STRONGLY ADvISED TO TAKE YOUR CHIPPER TO AN AUTHORISED AGENT FOR ALL BUT THE MOST ROUTINE MAINTENANCE AND CHECKS. -
Page 16: Service Schedule
Tow head maintenance. INSTRUCTION SHEET NOTE: Your Timberwolf wood chipper is covered by a full 12 months parts and labour warranty. Subject to correct maintenance and proper machine usage, the bearings are guaranteed for 12 months regardless of hours worked by the machine. In conditions of 'heavy usage' - i.e. in excess of 500 hours per year - it is recommended... -
Page 17: Safe Maintenance
CHECK FITTINGS The Timberwolf TW 230DHB is subject to large vibrations during the normal course of operation. Consequently there is always a possibility that nuts and bolts will work themselves loose. It is important that periodic checks are made to ensure the security of all fasteners. Fasteners should be tightened using a torque wrench to the required torque (see below). -
Page 18: Copper Ease Safety Information
TIMBERWOLF SERVICE INSTRUCTIONS TW 230DHB COPPER EASE SAFETY INFORMATION Product name: Copper Ease. Copper Ease contains no hazardous ingredients at or above regulatory disclosure limits, however, safety precautions should be taken when handling (use of oil-resistant gloves and saftey glasses are recommended - respiratory protection is not required). - Page 19 SERVICE INSTRUCTIONS TIMBERWOLF TW 230DHB BATTERY SAFETY INFORMATION...cont. 1. Storage and transport the positive output of the charger. Connect the - Batteries are filled with acid. negative terminal accordingly. - Always store and transport batteries upright - Switch on the charger only after the battery has...
-
Page 20: Change Blades
11. Reassemble the blades, bolts, washers and nuts in the order shown in the diagram 2. Remove battery leads. above. Use only genuine Timberwolf nuts and washers, as they are of a higher grade 3. Remove the 2 nuts retaining the access hatch, than normally stocked at fastener factories. -
Page 21: Tension Drive Belts
NOTE: There will normally be a rapid drop in tension during run-in period for new belts. When new belts are fitted, check the tension every 2 - 3 hours and adjust until the tension remains constant. Belt failures due to lack of correct tensioning will not be covered under your Timberwolf warranty. 1. Remove side panel. -
Page 22: Grease The Roller Spline And Rotor Bearings
TIMBERWOLF SERVICE INSTRUCTIONS TW 230DHB GREASE THE ROLLER SPLINE AND ROTOR BEARINGS NOTE: This should be done regularly. In dirty and dusty conditions or during periods of hard work it should be weekly. If the bearings and splines are allowed to run dry premature wear will occur resulting in a breakdown and the need for replacement parts. -
Page 23: Warranty Statement
- Performance of the required maintenance listed in your Entec Industries Ltd instruction manual. - In the event of a failure the Entec Industries Ltd authorised Timberwolf dealer is to be notified within 10 days of failure and the equipment is to be made available for unmolested inspection by the dealer technician. -
Page 24: Ec Declaration Of Conformity Certificate
TIMBERWOLF TW 230DHB CERTIFICATE OF CONFORMITY... -
Page 25: Identification Plate
TIMBERWOLF TW 230DHB IDENTIFICATION PLATE... -
Page 26: Decals
25 DECALS TIMBERWOLF TW 230DHB Decal Description Decal Description 4099 Danger. Hot exhaust Rotating blades. Keep hands and feet out. 2800 High velocity discharge - Reverse feed keep clear 2801 Personal Protective Forward feed Equipment required 19517 Warning 1661 Do not engage starter motor for more than 20 seconds. - Page 27 DECALS TIMBERWOLF TW 230DHB Decal Description Decal Description P653 P637 Danger. Danger. Rotating blades inside. Do not operate without this Stop engine and remove key cover in place. before removing discharge unit. P654 P652 Caution. Do not put road Caution. When transporting,...
-
Page 28: Electrical Detail
27 ELECTRICAL PARTS LOCATOR TIMBERWOLF TW 230DHB... -
Page 29: Circuit Diagram
CIRCUIT DIAGRAM TIMBERWOLF TW 230DHB... -
Page 30: Hydraulic Layout
29 HYDRAULIC LAYOUT TIMBERWOLF TW 230DHB Hose Kit P*1396 TANK FILTER 1115 1120 PUMP 1116 1119 1117 MOTOR MOTOR 1118... -
Page 31: Parts Lists
TIMBERWOLF TW 230DHB PARTS LISTS The following illustrations are for parts identification only. The removal or fitting of these parts may cause a hazard and should only be carried out by trained personnel. Page No. BELT TENSIONER CHASSIS (1) CHASSIS (1) WITH ADjUSTABLE TOWHEAD... -
Page 32: Belt Tensioner
31 BELT TENSIONER TIMBERWOLF TW 230DHB... - Page 33 CHASSIS (1) TIMBERWOLF TW 230DHB...
-
Page 34: Chassis
33 CHASSIS (1) TIMBERWOLF WITH ADJUSTABLE TOWHEAD TW 230DHB... -
Page 35: Chassis
CHASSIS (2) TIMBERWOLF TW 230DHB... -
Page 36: Control Box
35 CONTROL BOX TIMBERWOLF TW 230DHB... -
Page 37: Control Panel
CONTROL PANEL TIMBERWOLF TW 230DHB... -
Page 38: Discharge
37 DISCHARGE TIMBERWOLF TW 230DHB... -
Page 39: Drive Train
DRIVE TRAIN TIMBERWOLF TW 230DHB... -
Page 40: Electrical Layout
39 ELECTRICAL LAYOUT TIMBERWOLF TW 230DHB ITEM PART NO DESCRIPTION ITEM PART NO DESCRIPTION P*1335 Funnel Loom 1375 vEBattery Cable P*1337 Main Engine Loom 1376 vEBattery Cable... -
Page 41: Electrical Panel
ELECTRICAL PANEL TIMBERWOLF TW 230DHB... -
Page 42: Engine
41 ENGINE TIMBERWOLF TW 230DHB... -
Page 43: Engine Bay
ENGINE BAY TIMBERWOLF TW 230DHB... -
Page 44: Fuel Tank
43 FUEL TANK TIMBERWOLF TW 230DHB... -
Page 45: Funnel
FUNNEL TIMBERWOLF TW 230DHB... -
Page 46: Hydraulics
45 HYDRAULICS TIMBERWOLF TW 230DHB ITEM PART NO DESCRIPTION ITEM PART NO DESCRIPTION P*816F Hose Guard 0152 Washer Dowty 3/4” 0026 Adaptor mm 1/2”- 3/8” BSP 1766 Adapter 3/4” - 3/4” BSP 0398 Washer Dowty 1/2” 1583 Adaptor 1/2”- 3/4” BSP... -
Page 47: Roller Box
ROLLER BOX TIMBERWOLF TW 230DHB... -
Page 48: Roller Slides
47 ROLLER SLIDES TIMBERWOLF TW 230DHB... -
Page 49: Rotor
ROTOR TIMBERWOLF TW 230DHB... -
Page 50: Rotor Housing
49 ROTOR HOUSING TIMBERWOLF TW 230DHB... -
Page 51: V-Belt Tensioning Table
TIMBERWOLF V-BELT TENSIONING TABLE TW 230DHB...