3M Protecta Trolmatic User Instruction Manual
3M Protecta Trolmatic User Instruction Manual

3M Protecta Trolmatic User Instruction Manual

Controlled rescue emergency descent device with manual retract

Advertisement

Quick Links

User Instruction
Manual
M980000168 Rev. B
3M
Protecta
Controlled Rescue Emergency
Descent Device with Manual Retract.
Safety Information:
Please read, understand, and follow all safety information contained in these instructions prior to the use of this Pre-Engineered
Rescue System. FAILURE TO DO SO COULD RESULT IN SERIOUS INJURY OR DEATH.
These instructions must be provided to the user of this equipment. Retain these instructions for future reference.
Intended Use:
This Pre-Engineered Rescue System is intended for use as part of a complete personal fall protection and/or rescue system.
Use in any other application including, but not limited to, material handling, recreational or sports-related activities, or other
activities not described in the User Instructions, is not approved by 3M and could result in serious injury or death.
This system is only to be used by trained users in workplace applications.
Warning:
This Pre-Engineered Rescue System is intended for use as part of a complete personal fall protection
and/or rescue system. It is expected that all users be fully trained in the safe installation and operation of their
Pre-Engineered Rescue System. Misuse of this system could result in serious injury or death. For proper selection,
operation, installation, maintenance, and service, refer to these User Instructions and all manufacturer recommendations,
see your supervisor, or contact 3M Technical Service.
• To reduce the risks associated with working with a Pre-Engineered Rescue System which, if not avoided,
could result in serious injury or death:
-
Inspect the system before each use and at least annually. Inspect in accordance with the User Instructions.
-
If inspection reveals an unsafe or defective condition in the device or a component of the device, remove the device
from service and repair or replace according to the User Instructions.
-
Label the system 'UNUSABLE' and immediately remove the system from service if it has been subject to fall arrest
or impact force. Inspect and handle the system according to the User Instructions.
-
Ensure the rescue system and lifeline are kept free from all obstructions including, but not limited to, entanglement
with other workers, yourself, and surrounding objects.
-
Follow all manufacturer recommendations when connecting a lifeline.
-
When performing rescue operations, always utilize fall protection safety measures as determined by your workplace
rescue plan.
Trolmatic
®

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Protecta Trolmatic and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for 3M Protecta Trolmatic

  • Page 1 Use in any other application including, but not limited to, material handling, recreational or sports-related activities, or other activities not described in the User Instructions, is not approved by 3M and could result in serious injury or death. This system is only to be used by trained users in workplace applications.
  • Page 2 Avoid surfaces and objects that can damage the user or equipment. Ensure there is adequate fall clearance when working at height. Never modify or alter your fall protection equipment. Only 3M or parties authorized in writing by 3M may make repairs to the equipment.
  • Page 3 Important: If you have questions on the use, care, or suitability of this equipment for your application, contact 3M. Important: Record the product identification information from the ID label in the Inspection and Maintenance Log in Section 9.0 of this manual.
  • Page 4 F. Training: This equipment is intended to be installed and used by persons trained in its correct application and use. G. Operating and Storage Temperature: -40°C to 60°C ©3M 2020. All rights reserved.
  • Page 5: System Requirements

    The guide cable MUST be 12 mm diameter wire rope, galvanized or stainless steel. Bottom anchorage for the cable guide can be the 3M Pylon Anchor (ref : 7256000, but not CE-certified).
  • Page 6: Installation And Use

    B. Descent Path And Landing Area Clearance: Your descent path must be unobstructed. The landing area must be clear of obstructions to permit safe landing of the user. Failure to provide an unobstructed descent path and landing area may result in serious injury. ©3M 2020. All rights reserved.
  • Page 7 C. Testing The System: 3M™ recommends performing a test descent using a 75 kg weight. The descent speed should be uniform and allowed to reach the landing area safely. Remember to log any descent height (including test descents) in the Descent Log on Page 15 so that the cumulative descent height data is available.
  • Page 8 This is to avoid that you start the evacuation and are stopped by your primary fall arrest device that you forgot to disconnect. Sit down on the seat of the carriage while holding down the manual brake to keep the carriage in place. Front D-ring AG300 Figure 6 ©3M 2020. All rights reserved.
  • Page 9: Inspection Steps

    Inspect the guide cable. Inspect the wire rope for cuts, kinks, broken wires, corrosion, or severely worn areas. If the guide cable is damaged do not use the system. Step 9. Inspect each system component and subsystem according to manufacturer’s instructions. Step 10. Record inspection results in Section 9.0. ©3M 2020. All rights reserved.
  • Page 10: Maintenance

    1400 daN min breaking strength Angle of load-bearing 30° to 45° cable from horizontal: Speed of descent is Maximum 4 m/s, automatically regulated: average 2.5 m/s Maximum Load: 136 kg Standards: EN 341 class B ©3M 2020. All rights reserved.
  • Page 11 The guide cable and its associated components are available from 3M™, if required by the customer. 3M can also supply the guide cable and its associated components (thimbles and cable clamp) in kits. • Kit ref : 8900038 for AG360/I •...
  • Page 12: Inspection And Maintenance Log

    Inspection Items Noted Corrective Action Maintenance Performed Approved by: Approved by: Approved by: Approved by: Approved by: Approved by: Approved by: Approved by: Approved by: Approved by: Approved by: Approved by: Approved by: Approved by: ©3M 2020. All rights reserved.
  • Page 13 Inspection Items Noted Corrective Action Maintenance Performed Approved by: Approved by: Approved by: Approved by: Approved by: Approved by: Approved by: Approved by: Approved by: Approved by: Approved by: Approved by: Approved by: Approved by: ©3M 2020. All rights reserved.
  • Page 14 Inspection Items Noted Corrective Action Maintenance Performed Approved by: Approved by: Approved by: Approved by: Approved by: Approved by: Approved by: Approved by: Approved by: Approved by: Approved by: Approved by: Approved by: Approved by: ©3M 2020. All rights reserved.
  • Page 15 Descent Log Serial Number: Model Number: Date Purchased: Date of First Use: Date Descent Height Cumulative Descent Height ©3M 2020. All rights reserved.

Table of Contents