Quick Start Guide Foreword General This manual introduces the functions, installation, and operations of the camera. Safety Instructions The following categorized signal words with defined meaning might appear in the manual. Signal Words Meaning Indicates a medium or low potential hazard which, if not avoided, WARNING could result in slight or moderate injury.
Page 3
Quick Start Guide Please visit our website, contact the supplier or customer service if there is any problem occurred when using the device. If there is any uncertainty or controversy, please refer to our final explanation.
Quick Start Guide Important Safeguards and Warnings Electrical Safety All installation and operation shall conform to your local electrical safety codes. The power source shall conform to the Safety Extra Low Voltage (SELV) standard, and supply power with rated voltage which conforms to Limited power Source requirement according to IEC60950-1.
Page 5
Quick Start Guide It is recommended to ground the device to enhance reliability. Do not touch the image sensor (CMOS) directly. Dust and dirt can be removed with air blower, or you can wipe the lens gently with soft cloth that is moistened with alcohol. You can clean the device body with soft dry cloth, and for stubborn stains, use the cloth with ...
Quick Start Guide Introduction General This series of digital video cameras use internet protocol, and they can send and receive audio and video data through network independently. They are equipped with fisheye lens and advanced algorithm of fisheye image rectification; they support surveillance with no dead zone and panorama image output with multiple image screens, and every screen supports virtual Device Ports ...
Quick Start Guide Table 1-2 Alarm I/O port information Port Port Name Function ALARM_OUT Outputs alarm signal to alarm device. Alarm I/O ALARM_IN Receives the switch signal of external alarm source. ALARM_GND Ground connection. Connecting Alarm Input/output Alarm input/output is available on select models. Step 1 Connect alarm input device to the alarm input end of the I/O port.
Page 9
Quick Start Guide Figure 1-4 Mode B Step 3 Log in to web interface, and configure alarm input and alarm output in alarm setting. The alarm input on the web interface is corresponding to the alarm input end of the ...
Quick Start Guide Network Configuration Device initialization and IP address setting can be finished with the "ConfigTool" or on web interface. For more information, see the Web Operation Manual. Device initialization is available on select models, and it is required at first use or after the ...
Quick Start Guide The Device initialization interface is displayed. Step 6 Select the devices that need initialization, and then click Initialize. The password setting interface is displayed. See Figure 2-2. Figure 2-2 Password setting Step 7 Set and confirm the password of the devices, then enter a valid email address, and then click Next.
Quick Start Guide After clicking Search setting, enter the username and password, and make sure that they are the same as what you set during initialization; otherwise there will be wrong password notice. Step 2 Select the devices whose IP addresses need to be modified, and then click Modify IP. The Modify IP Address interface is displayed.
Page 13
Quick Start Guide Figure 2-4 Main interface...
Quick Start Guide Installation Packing List The tool required for the installation such as electric drill is not provided in the packing. The operation manual and related tool information are contained in the disk or the QR code, and the actual packing shall prevail.
Quick Start Guide Installing Device 3.3.1 Installation Type 3.3.2 Installing SD Card (Optional) Disconnect the power before installing or removing the SD card.
Quick Start Guide Press the WPS button on your router, and then press and hold the WPS button on the camera for 1-2 s, the camera would be connected to your router within 1 min. Press and hold the WPS button on the camera for at least 10 s during proper operation ...
Page 17
Quick Start Guide Mounting plate Positioning map Locking Mounting Plate The mounting plate is at the "open" state by default, make sure it stays "open" when installing the camera; and adjust it to the "close" state after installation. When the mounting plate is at the "open"...
Page 18
Quick Start Guide Fixing Device Cable going through the mounting surface...
Page 19
Quick Start Guide Cable going through the side cable tray...
Need help?
Do you have a question about the IPC-EW5541-AS and is the answer not in the manual?
Questions and answers