Table of Contents
Advertisement
Quick Links
Installation Instructions
Vantage Basin Taps With
Cross Head Handles
Models covered: VTX 1/2 C
Please keep this booklet for future
reference.
Installer, when you have read these
instructions please ensure you leave them
with the user.
For latest prices and delivery to your door visit MyTub Ltd - www.mytub.co.uk - info@mytub.co.uk
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Bristan Vantage VTX 1/2 C
Summary of Contents for Bristan Vantage VTX 1/2 C
- Page 1 Installation Instructions Vantage Basin Taps With Cross Head Handles Models covered: VTX 1/2 C Please keep this booklet for future reference. Installer, when you have read these instructions please ensure you leave them with the user. For latest prices and delivery to your door visit MyTub Ltd - www.mytub.co.uk - info@mytub.co.uk...
-
Page 2: Table Of Contents
Contents Thank you for choosing Bristan, the UK’s leading taps and showers expert. We have designed this product with your enjoyment in mind. To ensure that it works to its full potential, it needs to be fi tted correctly. These fi tting instructions have been created to give you all of the information you need and, if you need any further help, please do not hesitate to contact us. -
Page 3: Important Safety Information
Important Safety Information • Please read these instructions thoroughly and retain for future use. • All products manufactured and supplied by Bristan are safe provided they are installed, used correctly and receive regular maintenance in accordance with these instructions. •... -
Page 4: General Information
General Information Operating pressure range: Minimum 0.2 bar, Maximum 5.0 bar. Maximum static pressure: 10.0 bar. Designed to comply with BS EN 200 for single taps, for water systems of type 1 and 2 general technical specifi cations and to be used within systems designed to BS 6700. BS 6700 recommends the temperature of stored water should never exceed 65°C. -
Page 5: Pack Contents
Pack Contents 1. Flexible Connecting Pipes 2. Tap Body 3. Plinth 4. Cover Cap 5. Easy Fit Base 6. Backnut & Washer 7. 10mm Hexagonal Key For latest prices and delivery to your door visit MyTub Ltd - www.mytub.co.uk - info@mytub.co.uk... -
Page 6: Product Features
Product Features Cross Head Handles Easy to use 1/4 turn cross head handles make operating the taps easy when the users hands are wet. Built in Isolation Valves Both fl exible connecting pipes come with built in isolation valves, making servicing and maintenance quick and easy. -
Page 7: Specifi Cations
Specifi cations Inlet Connections: 15mm Compression fi tting with integral isolation valve Minimum working pressure: 0.2 bar Maximum working pressure: 5.0 bar Maximum static pressure: 10.0 bar System Requirements: Gravity fed hot & cold (Equal pressures) Gravity fed hot & cold (Differential pressure, maximum ratio 5:1) Unvented systems Instantaneous water heater (Combination boiler) Important: To ensure the tap fi... -
Page 8: Dimensions
Dimensions Dimensions are nominal and in millimetres. 15mm Compression fi tting with integral isolation valve For latest prices and delivery to your door visit MyTub Ltd - www.mytub.co.uk - info@mytub.co.uk... -
Page 9: Installation Requirements
Installation Requirements Flexible Connecting Pipes See below for recommended ways to fi t the Care must be taken when connecting the fl exible connecting pipes. fl exible connection pipes to the household pipework to ensure they do not bend sharply and kink or twist. -
Page 10: Installation
Installation Before installation Flush through the pipework to ensure 10mm hexagonal removal of debris. Turn off mains water supply and close any isolating valves. 1. Attach push-fi t connectors Place the ‘push-fi t connectors’ into the holes in the basin top, ensure the rubber Push-fi... - Page 11 Installation 4. Fit the tap body Remove the cover caps and place the plinths over the push-fi t connectors. Grease the push-fi t connectors using the sachet of grease provided. Push-fi t the tap body onto the connectors. Align the body and tighten both grub screws at the rear of the body using the long end of the 2.5mm hexagonal key as shown below until fi...
-
Page 12: Maintenance
fi tting, even the non- and holding dirt, which normal cloths scratch cleaners. leave behind. Order through your Bristan stockist (order code: ECLOTH). Cleaning the Valves Before carrying out any maintenance, turn... -
Page 13: Troubleshooting
Troubleshooting Symptom Cause Remedy No fl ow or low partially closed isolation valve. Open isolation valve. fl ow rate Instantaneous water heater Increase water fl ow rate or cycles on and off as fl ow rate or pressure through system. pressure is too low. -
Page 14: Guarantee
Guarantee At Bristan, we want to make things as • Repair under this guarantee does not easy as possible for our customers. That’s extend the original expiry date. The why we design products that are easy to guarantee on any replacement parts or fit and use, and that are quality tested to product ends at the original expiry date. - Page 15 ‘phone or with a spare part, then we’ll guarantee period, contact Bristan Care send out one of our Bristan Care Customer Service on 0844 701 6273 with engineers to take a look. Bristan Care...
- Page 16 Part Number: FI VTX 1/2 C Issue: D1 Useful contact details: Customer Service: 0844 7016273 Bristan Group Ltd. Customer Service Email: Birch Coppice Business Park Customercare@bristan.com Dordon Tamworth Customer Service Fax: Staffordshire 0844 7016275 B78 1SG Reception: Web: www.bristan.com 0844 7016274 Email: enquire@bristan.com...
Need help?
Do you have a question about the Vantage VTX 1/2 C and is the answer not in the manual?
Questions and answers