Scandomestic SV 80 User Manual page 11

Hide thumbs Also See for SV 80:
Table of Contents

Advertisement

Available languages

Available languages

• Temperature alarm: If the inner temperature is higher than 23°C,
the "HI" is shown in the display panel, and the buzzer alarm
after one hour continuosly. It informs that the inner temperature
is too high, plase check the reason.
• Set the desired cooling temperature by pressing the buttons
adjacent to the "set upper/set lower" program. Each depres-
sion of the buttons will scroll through the available temperature
settings (for each compartment) in increments of 1 degree.
The temperature selected will flash in the LED display for ap-
proximately 5 seconds, then revert back to display the setting
temperature of the cabinet.
- Both compartment: The temperature setting can be adjusted
from 5°C to 18°C.
• To view the actual temperature. (anytime) press and hold the
corresponding button for approximately 5 seconds, the actual
temperature will temporarily "flash" in the LED display for 5
seconds.
For SV 133
The controls of your Wine cooler (the upper zone and middle
zone)
POWER
RUN
LIGHT
Upper Chamber
• "RUN": Indicator light illuminates to signify the cooling mode is
currently in operation.
• "Light": control the inner light turn on/off.
• "Power": control this appliance turn on/off.
• "Set Upper": set the temperature of the upper chamber.
• "Set Middle": set the temperature of the middle chamber.
• "Up Chamber": shows the temperature of the up chamber.
• "Middle Chamber": shows the temperature of the middle
chamber.
Setting the Temperature Control
Each cooling compartment of the wine cooler (upper & lower) is in-
dependently controlled. To set the temperature:
• Connect the power cord to a properly grounded outlet. In the
event of a power interruption, all previous temperature settings
are automatically erased and each compartment will default to
a preset temperature setting of: 7°C for upper compartment and
7°C for middle compartment.
• Set the desired cooling temperature by pressing the buttons
adjacent to the "Set Upper/Set Middle" program. Each depres-
sion of the buttons will scroll through the available temperature
settings (for each compartment) in increments of 1 degree.
The temperature selected will flash in the LED display for ap-
proximately 5 seconds, then revert back to display the setting
temperature of the cabinet.
Upper compartment: The temperature setting can be adjusted
from 5°C to 18°C.
Middle compartment: The temperature setting can be adjusted
from 5°C to 10°C.
• To view the actual temperature (anytime) press and hold the
corresponding button, the actual temperature will temporarily
"flash" in the LED display for 5 seconds.
°C
°C
Set Upper
Set Middle
Middle Chamber
The controls of your Wine cooler (the Lower zone)
RUN
DISPLAY
• "Up": Used to raise(warm) the temperature in 1°C.
• "Down": Used to lower(cool) the temperature in 1°C.
• "Display": shows the temperature of the lower compartment.
Setting the Temperature Control
• Connect the power cord to a properly grounded outlet. In the
event of a power interruption, all previous temperature settings
are automatically erased and it will default to a preset tempera-
ture setting of: 12°C.
• Set the desired cooling temperature by pressing the buttons
adjacent to the "UP/DOWN" program. Each depression of the
buttons will scroll through the available temperature settings in
increments of 1 degree. The temperature selected will flash in
the LED display for approximately 5 seconds, then revert back to
display the setting temperature of the cabinet.
• The temperature setting can be adjusted from 10°C to 18°C
Shelves
• To prevent damaging the door gasket, make sure to have the
door all the way opened when pulling shelves out of the rail
compartment.
• For easy access to the storage content, you must pull the shelves
approximately 1/3 out of the rail compartment, however this
unit was designed with a notch on each sides of the shelf tracks
to prevent bottles from falling.
For SV 80/ SV 90
• When removing any of these shelves out of the rail compart-
ment, To fit or remove the shelf, tilt the shelf as per the diagram
and simply pull out, or push in the shelf until it sits on the sup-
port brackets securely.
11
°C
UP
DOWN

Hide quick links:

Advertisement

Table of Contents
loading

This manual is also suitable for:

Sv 90Sv 102Sv 110Sv 122Sv 133

Table of Contents