BendPak HD-973P Installation And Operation Manual
  1. Manuals
  2. Brands
  3. BendPak Manuals
  4. Lifting Systems
  5. HD-973P
  6. Installation and operation manual

BendPak HD-973P Installation And Operation Manual

Multi-level parking lift
Hide thumbs Also See for HD-973P:
Table of Contents

Advertisement

Quick Links

Installation and Operation Manual
Manual P/N 5900076 — Manual Revision B— February 2020
Model:
• HD-973P
• HD-973PX
Designed and engineered by BendPak Inc. in Southern California, USA. Made in China.
⚠
DANGER
Multi-Level Parking Lift
entire
Read the
Failure to follow the instructions and safety precautions in this manual can
result in serious injury or death. Make sure all other operators also read
this manual. Keep the manual near the product for future reference.
By proceeding with installation and operation, you agree
that you fully understand the contents of this manual and
assume full responsibility for product use
contents of this manual
1645 Lemonwood Dr.
Santa Paula, CA 93060 USA
Toll Free: (800) 253-2363
Tel: (805) 933-9970
bendpak.com
before
using this product.
.

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the HD-973P and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for BendPak HD-973P

Summary of Contents for BendPak HD-973P

  • Page 1 Installation and Operation Manual Manual P/N 5900076 — Manual Revision B— February 2020 Model: • HD-973P • HD-973PX Designed and engineered by BendPak Inc. in Southern California, USA. Made in China. ⚠ entire before Read the contents of this manual using this product.
  • Page 2 Copyright. Copyright © 2020 by BendPak Inc. All rights reserved. You may make copies of this document if you agree that: you will give full attribution to BendPak Inc., you will not make changes to the content, you do not gain any rights to this content, and you will not use the copies for commercial purposes.

  • Page 3: Table Of Contents

    Installation Introduction This manual describes the following BendPak Parking Lift: HD-973P: Multi-Level Parking Lift that can raise Vehicles up to 7,000 lbs (3,175 kg) on the Upper • Platform and up to 9,000 lbs (4,082 kg) on the Lower Platform.

  • Page 4: Shipping Information

    Keep this manual on or near the product for future reference. Read and follow the warnings and instructions on the labels on the product. Contact BendPak at (800) 253-2363 or if you need replacement labels or a replacement support@bendpak.com...
  • Page 5 Check for damaged, worn, or missing parts. Do not use it if you find any of these issues. Instead, take it out of service, then contact an authorized repair facility, your dealer, or BendPak at (800) 253-2363 or techsupport@bendpak.com. •...

  • Page 6: Components

    Lift. Used to lower the Runways. • Ladders. Pieces of steel that gets installed at the back of each Post; these are part of the Safety Lock system. HD-973P Multi-Level Parking Lift P/N 5900076 — Rev. B — February 2020...
  • Page 7 The Front of the Lift is the end opposite the Drive-up Ramps. Front view. HD-973P Multi-Level Parking Lift P/N 5900076 — Rev. B — February 2020...

  • Page 8: Specifications

    Specifications Side View Top View HD-973P Multi-Level Parking Lift P/N 5900076 — Rev. B — February 2020...
  • Page 9 95" is 50 percent of the Top Platform’s rated capacity (or 3,500 lbs when the rated capacity is 7,000 lbs). Specifications subject to change without notice. HD-973P Multi-Level Parking Lift P/N 5900076 — Rev. B — February 2020...
  • Page 10 100" is 50 percent of the Top Platform’s rated capacity (or 3,500 lbs when the rated capacity is 7,000 lbs). Specifications subject to change without notice. HD-973P Multi-Level Parking Lift P/N 5900076 — Rev. B — February 2020...

  • Page 11: Faqs

    Cars, trucks, SUVs; anything that fits on the Upper Platform, up to 7,000 lbs (3,175 kg). The Lower Platform holds up to 9,000 lbs (4,082 kg). Q: What is the difference between the HD-973P and the HD-973P A: The HD-973PX is a taller Lift with a higher rise and extended Runways.

  • Page 12: Installation Checklist

    35. Lubricate the Lift. ☐ 36. Bleed the Hydraulic Cylinder. ☐ 37. Test the Lift. ☐ 38. Review the final checklist. ☐ 39. Leave the manual for the owner/operator. HD-973P Multi-Level Parking Lift P/N 5900076 — Rev. B — February 2020...

  • Page 13: Installation

    Only fully trained personnel should be involved in installing this equipment. Pay attention at all times. Use appropriate tools and lifting equipment. Stay clear of moving parts. BendPak recommends referring to the latest version of the ANSI/ALI ALIS Standard (R2015) Safety Requirements for Installation and Service for more information about safely installing, using, and servicing your Lift.
  • Page 14 Front of the Lift, and no obstructions at all at the Rear of the Lift so you can safely drive Vehicles on and off the Runways. HD-973P Multi-Level Parking Lift P/N 5900076 — Rev. B — February 2020...
  • Page 15 Do not shim a Post more than half an inch using the provided Shims and Anchor NOTICE Bolts. A maximum shim of 2 inches is possible by ordering optional Shim Plates. Contact BendPak at (800) 253-2363, extension 191 to order. Please have the model and serial number of your Lift available. •...
  • Page 16 Top view. Hydraulic Cylinder is underneath the Runway. The Drive-up Ramps are not affected by the Power Post location. Drawing not to scale. Some components not shown. HD-973P Multi-Level Parking Lift P/N 5900076 — Rev. B — February 2020...
  • Page 17 Do not use the Total Length value Note: ; this includes the Ramps, which are not taken into consideration for creating Chalk Line Guides. Top view. Not drawn to scale. Not all components shown. HD-973P Multi-Level Parking Lift P/N 5900076 — Rev. B — February 2020...
  • Page 18 The Posts and Runways are delivered with stabilizing structures on each end. Be very careful when removing these stabilizing structures; the Posts and Runways can shift or even fall. If they fall on a person, they could cause serious injury. HD-973P Multi-Level Parking Lift P/N 5900076 — Rev. B — February 2020...
  • Page 19 Using a Forklift or Shop Crane, carefully move each Post to the inside corners of the Chalk Line Guides. Do not stand up the Posts yet ; some of the following procedures are easier to complete if the Posts are laying on the ground. HD-973P Multi-Level Parking Lift P/N 5900076 — Rev. B — February 2020...
  • Page 20 Top view. Drawing shows the Power Post in the Rear-Passenger Side. Windows are in the Crosstubes; they are shown here at the ends of the Powerside Runway for clarity. Drawing not to scale. Some components not shown. HD-973P Multi-Level Parking Lift P/N 5900076 — Rev. B — February 2020...
  • Page 21 With the Posts on the ground, slide the Crosstubes into place. must Both Windows be on the ends of the Powerside Runway and facing the inside of the Lift. Perform Step 2 for the other two Crosstubes. HD-973P Multi-Level Parking Lift P/N 5900076 — Rev. B — February 2020...
  • Page 22 Safeties cannot engage. However, if a Cable were to break (which very rarely happens), the Slack Safety for the broken Cable immediately engages, preventing the Runways from falling. HD-973P Multi-Level Parking Lift P/N 5900076 — Rev. B — February 2020...
  • Page 23 Platform in danger. Slots are created by the Slide Blocks on the Crosstube Gusset. Front and Side views combined. Not to scale. Not all components are shown. HD-973P Multi-Level Parking Lift P/N 5900076 — Rev. B — February 2020...
  • Page 24 The other hole in the Top Cap is for the Lifting Cable that is routed to the top of the Post, which is done later in the installation. Install the remaining Top Caps the same way. HD-973P Multi-Level Parking Lift P/N 5900076 — Rev. B — February 2020...
  • Page 25 Once both Crosstubes are in position, , and the Slack Safeties have been disengaged, you can continue with the installation. Repeat Steps 1 through 3 for the other Platform. HD-973P Multi-Level Parking Lift P/N 5900076 — Rev. B — February 2020...
  • Page 26 Make sure that all eight Ladders are correctly installed and secured. If the Ladder misses a Slot, your Safety Locks will function correctly, which is a danger to anyone under the Platform that is holding a Vehicle or around it. HD-973P Multi-Level Parking Lift P/N 5900076 — Rev. B — February 2020...
  • Page 27 Do not use Shims and/or Anchor Bolt to Shim more than 1/2 an inch. You can order 2 inch Shim Plates for extreme cases. Do not anchor the Posts at this point HD-973P Multi-Level Parking Lift P/N 5900076 — Rev. B — February 2020...
  • Page 28 Platform. Pull Box and Side Sheaves are for Upper Platform only. Not to scale. Not all components shown. HD-973P Multi-Level Parking Lift P/N 5900076 — Rev. B — February 2020...
  • Page 29 Tube (which holds the Air, Return, and Hydraulic Hoses). Top View. The opening on the inside of the Powerside Runway is for the Upper Platform only. Not to scale. Not all components shown. HD-973P Multi-Level Parking Lift P/N 5900076 — Rev. B — February 2020...
  • Page 30 Do not continue with the installation until you have visually confirmed that all four WARNING Safety Locks are engaged on each Platform. If they are not engaged, the Runways could move or fall, possibly causing personal injury or product damage. HD-973P Multi-Level Parking Lift P/N 5900076 — Rev. B — February 2020...
  • Page 31 Threaded end. You have to match the Cable letter with the length information. • The Lifting Cables for the HD-973P are: • The Lifting Cables for the HD-973PX are:  Upper Platform:  Upper Platform: o A: 5,704 mm / 19 feet / 224.5 in.
  • Page 32 The following drawing shows the routing for all four Lifting Cables on the Upper Platform. Cable Sheaves separated from Windows for clarity. Crosstubes not shown. Not to scale. HD-973P Multi-Level Parking Lift P/N 5900076 — Rev. B — February 2020...
  • Page 33 Post, it must be between where the Gusset Sheave will go not in this exact and where the Slack Safety Sheave already is. If the Cable is location , the Slack Safeties will work correctly later on. HD-973P Multi-Level Parking Lift P/N 5900076 — Rev. B — February 2020...
  • Page 34 Position the Lifting Cables on the correct side of the Pull Box, with the Button ends of both heading back out of the Pull Box. With the Cables in place, reinstall the Double Cable Sheave in the Pull Box. HD-973P Multi-Level Parking Lift P/N 5900076 — Rev. B — February 2020...
  • Page 35 Lifting Cables, depending on how far the Piston was extended. If you see slack in the Lifting Cables, this is normal. It will go away once you start using the Lift. HD-973P Multi-Level Parking Lift P/N 5900076 — Rev. B — February 2020...
  • Page 36 Route the Button end of Lifting Cable D towards the Crosstube with Large Windows, where Lifting Cable B is. Gather the Button ends of Lifting Cables B and D, making sure to position Lifting Cable B below Lifting Cable D. HD-973P Multi-Level Parking Lift P/N 5900076 — Rev. B — February 2020...
  • Page 37 Lifting Cables, depending on how far the Piston was extended. If you see slack in the Lifting Cables, this is normal. It will go away once you start using the Lift. HD-973P Multi-Level Parking Lift P/N 5900076 — Rev. B — February 2020...
  • Page 38 Button end of the Cable into the correct slot. The following drawing shows the routing for all four Cables on the Lower Platform. Cable Sheaves separated from Windows for clarity. Crosstubes not shown. Not to scale. HD-973P Multi-Level Parking Lift P/N 5900076 — Rev. B — February 2020...
  • Page 39 , the Slack Safeties will work correctly later on. With the Lifting Cable in place, reinstall the Gusset Sheave and the Cable Lock Pin in Post A. HD-973P Multi-Level Parking Lift P/N 5900076 — Rev. B — February 2020...
  • Page 40 Pull the Button Ends of Lifting Cables A and C back towards the middle of the Runway, past the Retaining Plate, and into its slot on the Tie Plate. Drawing shows a front view of the Tie Plate, facing towards the Crosstube with Medium Windows. HD-973P Multi-Level Parking Lift P/N 5900076 — Rev. B — February 2020...
  • Page 41 Pull the Button Ends of Cable B and D back towards the middle of the Runway, past the Retaining Plate, and into its Slot on the Tie Plate. Drawing shows a front view of the Tie Plate, facing towards the Crosstube with Medium Windows. HD-973P Multi-Level Parking Lift P/N 5900076 — Rev. B — February 2020...
  • Page 42 The Ferrule goes around the Rod and under the Threads. The Nut goes onto the Threads. Tighten the Nut. Remember that the Ferrule can only be used once; do not tighten the Nut until everything is ready. HD-973P Multi-Level Parking Lift P/N 5900076 — Rev. B — February 2020...
  • Page 43 The Air Line Elbow Connectors on the Crosstube Gussets come installed from the factory. Drawing not to scale. Some components not shown. Air Lines shown outside Steel Tubes for clarity. HD-973P Multi-Level Parking Lift P/N 5900076 — Rev. B — February 2020...
  • Page 44 Leave the Power Unit end of the Air Line hanging out of the Flex Tube opening for now. It will be connected to a Tee Fitting and the Pushbutton Air Valve later. Repeat Steps 1 through 5 for the other Platform. HD-973P Multi-Level Parking Lift P/N 5900076 — Rev. B — February 2020...
  • Page 45 Leave the Power Unit end of the Return Line hanging out of the Flex Tube opening for now. It will be connected to a Tee Fitting and then to the Power Unit later in the installation. Repeat Steps 1through 8 for the other Platform. HD-973P Multi-Level Parking Lift P/N 5900076 — Rev. B — February 2020...
  • Page 46 Hydraulic Hoses and Fittings on the Lift, making your new Lift inoperable. Your Lift is shipped with clean components; however, BendPak strongly recommends that you take secondary precaution and clean all Hydraulic Hoses and Fittings prior to making connections. It is better and less costly to take these extra steps now so that you do not need to take your Lift out of service later to fix issues that could have been prevented at the time of installation.
  • Page 47 If you put too much, the excess liquid will be pushed out when the Fitting is tightened; use a rag to wipe the excess. Tighten the Fitting into the connector; do over tighten the Fitting. Allow the manufacturer-recommended curing time before pressurizing the system. HD-973P Multi-Level Parking Lift P/N 5900076 — Rev. B — February 2020...
  • Page 48 NPT to ORB Hydraulic Fitting. The NPT end attaches to the Platform Selector Valve and the ORB end attaches to the Power Unit. One total. The following drawing shows where the Hydraulic Hose goes on the Lift. HD-973P Multi-Level Parking Lift P/N 5900076 — Rev. B — February 2020...
  • Page 49 After all connections have been made, make sure all connections are securely tightened. Note: The JIC – NPT Nipple Fittings and NPT – ORB Nipple Fitting will be connected to the Power Unit later in the installation. HD-973P Multi-Level Parking Lift P/N 5900076 — Rev. B — February 2020...
  • Page 50 There is no Safety Shutoff Bar to install under the Lower Platform, so you can hold off installing the Aluminum Decks (two shorter Decks) if you want, whatever works best for your installation process. HD-973P Multi-Level Parking Lift P/N 5900076 — Rev. B — February 2020...
  • Page 51 Make sure the Microswitch is snug against the Mounting Plate. The Microswitch will be connected to a cable that goes to the Power Unit later in the installation. HD-973P Multi-Level Parking Lift P/N 5900076 — Rev. B — February 2020...
  • Page 52 If you are going to install the Flex Tube Bracket Plate and/or the Zero Angle Bracket at the same time as the Power Unit, now is the time to put those into place. The Power Unit is heavy. BendPak recommends having one person hold the Power Unit while another person bolts it into place.
  • Page 53 Includes the holes to which the Flex Tubes connect. BendPak recommends orienting the Flex Tubes so that the lines coming out of it are near where they connect on the Power Unit and to the Pushbutton Air Valve.
  • Page 54 Tubes are best positioned for connecting the Return Line, the Air Line, and the Hydraulic Hose. The Flex Tube Angle Plate can be connected on either side of the Flex Tube Bracket Plate. HD-973P Multi-Level Parking Lift P/N 5900076 — Rev. B — February 2020...
  • Page 55 Screw the Plastic Nut back onto the Threads and tighten. Once in place, push the Hydraulic Hose, Return Line, and Air Line through the Flex Tube. Repeat Steps 1 through 6 for the other Platform. HD-973P Multi-Level Parking Lift P/N 5900076 — Rev. B — February 2020...
  • Page 56 Use the two holes on the Pushbutton Air Valve on the side away from the actual pushbutton. If you use the holes next to the pushbutton, the Zero Angle Bracket interferes with the pushbutton when you try to use it. HD-973P Multi-Level Parking Lift P/N 5900076 — Rev. B — February 2020...
  • Page 57 . Double check to make sure you are attaching the Air Line to the Pushbutton Air Valve. For the customer-supplied air pressure, a minimum of 75 PSI. HD-973P Multi-Level Parking Lift P/N 5900076 — Rev. B — February 2020...
  • Page 58 Return Line to the Power Unit and not the Air Line. Do not attach the Air Line to the Power Unit by mistake HD-973P Multi-Level Parking Lift P/N 5900076 — Rev. B — February 2020...
  • Page 59 Valve. Double check that you have the correct Hydraulic Hose. Find the Hydraulic Hose for the Lower Platform and connect it to the Left side of the Valve. HD-973P Multi-Level Parking Lift P/N 5900076 — Rev. B — February 2020...
  • Page 60 Never expose the motor to rain or other damp environments; damage to the motor caused by water is covered by the warranty. HD-973P Multi-Level Parking Lift P/N 5900076 — Rev. B — February 2020...
  • Page 61 25 amp or greater fuse. The following drawing shows the configuration for the Power Unit. P1/P2 represents the Hydraulic Power Out; T1/T2 or CV1/CV2 commonly represents the Hydraulic Return. HD-973P Multi-Level Parking Lift P/N 5900076 — Rev. B — February 2020...
  • Page 62 Double check to make sure the Hydraulic Fluid Reservoir has an adequate supply of fluid. ⚠ WARNING Do not run the Lift without an adequate supply of Hydraulic Fluid; you will damage the Power Unit. HD-973P Multi-Level Parking Lift P/N 5900076 — Rev. B — February 2020...
  • Page 63 (NEC) requirement. They are designed to interrupt electrical power in the event of an electrical circuit fault, emergency situation, or when equipment is undergoing service or maintenance. BendPak strongly recommends that you install a Power Disconnect Switch that is properly rated for the incoming power. ⚠...
  • Page 64 Concrete or Anchor Bolts do not meet these specifications, it could lead to product damage, Vehicle damage, personal injury, or even death. BendPak Lifts are supplied with installation instructions and concrete fasteners meeting the criteria as prescribed by the American National Standard “Automotive Lifts – Safety Requirements for Construction, Testing, and Validation”...
  • Page 65 ¾ inch diameter Anchor Bolt, for example, use a ¾ inch diameter drill bit. Vacuum each hole clean. BendPak recommends using a vacuum to clean the hole. You can also use a wire brush, hand make sure to thoroughly clean each hole pump, or compressed air;...
  • Page 66 Do not shim a Post more than half an inch using the provided Shims. A maximum of 2 inches is possible by ordering optional Shim Plates. Contact BendPak at (800) 253-2363, extension 191 to order. Please have the model and serial number of your Lift available.
  • Page 67 Lower Platform. Repeat Steps 1 through 5 for the Lower Platform. When you are satisfied the Lift is level, firmly secure the Nuts at the top of each Post. HD-973P Multi-Level Parking Lift P/N 5900076 — Rev. B — February 2020...
  • Page 68 Repeat Steps 1 and 2 for the remaining three Tire Stops. Make sure to chock the Vehicle’s Rear Tires when you position it in place on the Runways. HD-973P Multi-Level Parking Lift P/N 5900076 — Rev. B — February 2020...
  • Page 69 Place the Ramp in the Lip of the Hinge, then secure two Rotor Clips on either end of the Pin. Side View. Not to scale. Not all components shown. Repeat Steps 2 and 3 for the other Ramp. HD-973P Multi-Level Parking Lift P/N 5900076 — Rev. B — February 2020...
  • Page 70 Connect the Crossbeam on both ends to the Mounting Brackets using a Bolt, Washer and Nut for each hole, then tighten until secure. Repeat Steps 2 and 3 for the remaining Crossbeams. HD-973P Multi-Level Parking Lift P/N 5900076 — Rev. B — February 2020...
  • Page 71 You can damage your motor by running it without enough Hydraulic Fluid in the reservoir. If your Lift is still moving erratically or making odd noises after bleeding the Hydraulic System, refer to Troubleshooting for more information. HD-973P Multi-Level Parking Lift P/N 5900076 — Rev. B — February 2020...
  • Page 72 Test the Lift BendPak strongly recommends doing an Operational Test of your Lift with a standard Vehicle on each Platform before starting normal service (a typical Vehicle is not required, but is recommended). During the Operational Test, watch the Lift and its components and check for proper installation and operation.

  • Page 73: Operation

    Double check you have everything you need out of the Vehicle before raising the Lift. Make sure the Vehicle is not overbalanced on either end or either side. HD-973P Multi-Level Parking Lift P/N 5900076 — Rev. B — February 2020...
  • Page 74 Runways. Located on one side or the other of the Power Unit (depending on where it was installed). Pressing and holding the pushbutton on the Pushbutton Air Valve disengages the Safety Locks, which is needed to lower the Runways. HD-973P Multi-Level Parking Lift P/N 5900076 — Rev. B — February 2020...
  • Page 75 When the Platform gets to the desired height, go up a little bit more, then release the Up button and press and hold the Lowering Handle. The Platform backs down onto the most recently passed Safety Lock. HD-973P Multi-Level Parking Lift P/N 5900076 — Rev. B — February 2020...
  • Page 76 Make sure that the Lower Platform is on a Locking position before driving a Vehicle under it. ⚠ WARNING Never walk under raised Platforms—always walk around and stay clear at all times. HD-973P Multi-Level Parking Lift P/N 5900076 — Rev. B — February 2020...
  • Page 77 When the Upper Platform is fully resting on the Stop Blocks, release the Pushbutton Air Valve and the Lowering Handle. Remove the Tire Chocks, then carefully drive the Vehicle off of the Runways. HD-973P Multi-Level Parking Lift P/N 5900076 — Rev. B — February 2020...

  • Page 78: Maintenance

    ⚠ WARNING Do not operate your Lift if you find maintenance issues; instead, take the Lift out of service, then contact your dealer, visit bendpak.com/support, email techsupport@bendpak.com, or call (800) 253-2363. HD-973P Multi-Level Parking Lift P/N 5900076 — Rev. B — February 2020...
  • Page 79 Visually check for any broken wires. One way to check for crown breaks is to run a cloth along the rope to check for possible snags. d. With an awl, probe between wires and strands and raise any wires that appear loose. HD-973P Multi-Level Parking Lift P/N 5900076 — Rev. B — February 2020...

  • Page 80: Troubleshooting

    Crosstubes using white lithium grease. If the Lift is new, a break-in period may be needed; run the Lift several times each day. If the noises persist, contact BendPak Support. If you continue to have issues with your Lift, take it out of service, then contact your dealer, go to bendpak.com/support, email...

  • Page 81: Wiring Diagrams

    Wiring Diagrams 5585186 5585503 HD-973P Multi-Level Parking Lift P/N 5900076 — Rev. B — February 2020...
  • Page 82 5585312 5585512 5585173 HD-973P Multi-Level Parking Lift P/N 5900076 — Rev. B — February 2020...
  • Page 83 This section describes wiring information for the Microswitch(es), depending on the Power Unit you may have. Single Phase HD-973P Multi-Level Parking Lift P/N 5900076 — Rev. B — February 2020...
  • Page 84 Three Phase HD-973P Multi-Level Parking Lift P/N 5900076 — Rev. B — February 2020...

  • Page 85: Labels

    Labels HD-973P Multi-Level Parking Lift P/N 5900076 — Rev. B — February 2020...
  • Page 86 HD-973P Multi-Level Parking Lift P/N 5900076 — Rev. B — February 2020...
  • Page 87 HD-973P Multi-Level Parking Lift P/N 5900076 — Rev. B — February 2020...

  • Page 88: Parts Drawings

    Parts Drawings HD-973P Multi-Level Parking Lift P/N 5900076 — Rev. B — February 2020...
  • Page 89 HD-973P Multi-Level Parking Lift P/N 5900076 — Rev. B — February 2020...
  • Page 90 HD-973P Multi-Level Parking Lift P/N 5900076 — Rev. B — February 2020...
  • Page 91 HD-973P Multi-Level Parking Lift P/N 5900076 — Rev. B — February 2020...
  • Page 92 HD-973P Multi-Level Parking Lift P/N 5900076 — Rev. B — February 2020...
  • Page 93 HD-973P Multi-Level Parking Lift P/N 5900076 — Rev. B — February 2020...
  • Page 94 HD-973P Multi-Level Parking Lift P/N 5900076 — Rev. B — February 2020...
  • Page 95 HD-973P Multi-Level Parking Lift P/N 5900076 — Rev. B — February 2020...
  • Page 96 HD-973P Multi-Level Parking Lift P/N 5900076 — Rev. B — February 2020...
  • Page 97 HD-973P Multi-Level Parking Lift P/N 5900076 — Rev. B — February 2020...
  • Page 98 HD-973P Multi-Level Parking Lift P/N 5900076 — Rev. B — February 2020...
  • Page 99 HD-973P Multi-Level Parking Lift P/N 5900076 — Rev. B — February 2020...
  • Page 100 HD-973P Multi-Level Parking Lift P/N 5900076 — Rev. B — February 2020...
  • Page 101 HD-973P Multi-Level Parking Lift P/N 5900076 — Rev. B — February 2020...
  • Page 102 HD-973P Multi-Level Parking Lift P/N 5900076 — Rev. B — February 2020...
  • Page 103 HD-973P Multi-Level Parking Lift P/N 5900076 — Rev. B — February 2020...
  • Page 104 1645 Lemonwood Drive Santa Paula, CA, 93060 USA © 2020 BendPak Inc. All rights reserved. bendpak.com...

This manual is also suitable for:

Hd-973px

Table of Contents