1. Manuals
  2. Brands
  3. BendPak Manuals
  4. Lifting columns
  5. HD-973P
  6. Installation and operation manual

BendPak HD-973P Installation And Operation Manual

Multi-level parking lift
Hide thumbs Also See for HD-973P:
Table of Contents

Advertisement

Quick Links

Download this manual
Installation and Operation Manual
Models:
• HD-973P
• HD-973PX
Original Instructions in
the English language.
Designed and engineered by BendPak Inc. in Southern California, USA. Made in China.
IMPORTANT Safety Instructions, save these instructions! Read the entire contents of
this manual before using this product. Failure to follow the instructions and safety precautions in this
manual can result in severe injury or death. Make sure all other operators also read this manual. Keep
the manual near the product for future reference.
agree that you fully understand the contents of this manual and assume full responsibility
for product use.
Multi-Level Parking Lift
Manual P/N 5900076 — Manual Revision B3— January 2024
⚠
DANGER
By proceeding with setup and operation, you
1645 Lemonwood Dr.
Santa Paula, CA 93060 USA
Toll Free: (800) 253-2363
Telephone: (805) 933-9970
bendpak.com
HD-973P
Pictured

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the HD-973P and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for BendPak HD-973P

Summary of Contents for BendPak HD-973P

  • Page 1 Original Instructions in the English language. ⚠ Designed and engineered by BendPak Inc. in Southern California, USA. Made in China. DANGER IMPORTANT Safety Instructions, save these instructions! Read the entire contents of this manual before using this product. Failure to follow the instructions and safety precautions in this manual can result in severe injury or death.
  • Page 2 Copyright. Copyright © 2024 by BendPak Inc. All rights reserved. You may make copies of this document if you agree that: you will give full attribution to BendPak Inc., you will not make changes to the content, you do not gain any rights to this content, and you will not use the copies for commercial purposes.
  • Page 3 Unit Information. Enter the Model Number, Serial Number, and the Date of Manufacture from the ID label on your unit. This information is required for part or warranty issues. Model: Serial: Date of Manufacture:...

  • Page 4: Table Of Contents

    Installation Introduction This manual describes the following BendPak Parking Lift: HD-973P: Multi-Level Parking Lift that can raise Vehicles up to 7,000 lbs. (3,175 kg) on the Upper • Platform and up to 9,000 lbs. (4,082 kg) on the Lower Platform.

  • Page 5: Shipping Information

    900 chemicals identified by the State of California to cause cancer, birth defects or reproductive harm. Always use this product in accordance with BendPak’s instructions. For more information, visit www.p65warnings.ca.gov.
  • Page 6 BendPak at (800) 253-2363, option 7 then 4, or email support@bendpak.com. • BendPak recommends making a thorough inspection of the Lift at least once a year. Replace any damaged or severely worn parts, decals, or warning labels. HD-973P Series Multi-Level Parking Lift...
  • Page 7 BendPak assumes no liability for damages resulting from: • Use of the equipment for purposes other than those described in this manual. • Modifications to the equipment without prior, written permission from BendPak. • Injury or death caused by modifying, disabling, overriding, or removing safety features. •...

  • Page 8: Components

    Safety Ladders. Steel components that look similar to a ladder and are installed at the back of each Post. The Safety Locks on the Platforms engage the openings in the Safety Ladders. HD-973P Series Multi-Level Parking Lift P/N 5900076 — Rev. B3 — January 2024...
  • Page 9 The Front of the Lift is the end opposite the Drive-up Ramps. Front view. HD-973P Series Multi-Level Parking Lift P/N 5900076 — Rev. B3 — January 2024...

  • Page 10: Specifications

    Specifications Top View Side View Approach View HD-973P Series Multi-Level Parking Lift P/N 5900076 — Rev. B3 — January 2024...
  • Page 11 Lift installation, but the additional clearance around the Posts is required. Specifications subject to change without notice. HD-973P Series Multi-Level Parking Lift P/N 5900076 — Rev. B3 — January 2024...
  • Page 12 Lift installation, but additional clearance around the Posts is required. Specifications subject to change without notice. HD-973P Series Multi-Level Parking Lift P/N 5900076 — Rev. B3 — January 2024...

  • Page 13: Faq

    Platforms either fully lowered or engaged on a Safety Lock. Q: Can I install my Lift outside? A: HD-973P and PX Lifts are approved for indoor installation and use only. Outdoor installation is prohibited. For outdoor installations, see models HD-973PG and PGX.

  • Page 14: Installation Checklist

    35. Lubricate the Lift. ☐ 36. Bleed the Hydraulic Cylinder. ☐ 37. Test the Lift. ☐ 38. Review the final checklist. ☐ 39. Leave the manual for the owner/operator. HD-973P Series Multi-Level Parking Lift P/N 5900076 — Rev. B3 — January 2024...

  • Page 15: Installation

    Only fully trained personnel should be involved in installing this equipment. Always pay attention. Use appropriate tools and lifting equipment. Stay clear of moving parts. BendPak recommends referring to the ANSI/ALI ALIS Standard (current edition) Safety Requirements for Installation and Service for more information about safely installing, using, and servicing your Lift.
  • Page 16 Specifications is how high the mechanism can rise before stopping; the Safety Locks height is different from maximum rise. Refer to the figure on the next page. HD-973P Series Multi-Level Parking Lift P/N 5900076 — Rev. B3 — January 2024...
  • Page 17 Do not shim a Post more than half an inch using the provided Shims and Anchor Bolts. A maximum shim of 2 inches is possible by ordering optional Shim Plates. Contact BendPak at (800) 253-2363, select option 7 then 5 to order. Please have the model and serial number of your Lift available.
  • Page 18 ⚠ CAUTION BendPak lifts are supplied with installation instructions and concrete anchors that meet the criteria set by the American National Standard “Automotive Lifts – Safety Requirements for Construction, Testing, and Validation,” ANSI/ALI ALCTV. You are responsible for any special regional structural and/or seismic anchoring requirements specified by any other agencies and/or codes such as the Uniform Building Code (UBC) and/or International Building Code (IBC).
  • Page 19 Top view. Hydraulic Cylinder is underneath the Runway. The Drive-up Ramps are not affected by the Power Post location. Drawing not to scale. Some components not shown. HD-973P Series Multi-Level Parking Lift P/N 5900076 — Rev. B3 — January 2024...
  • Page 20 Do not use the Total Length value; this includes the Ramps, which are not taken into Note: consideration for creating Chalk Line Guides. Top view. Not drawn to scale. Not all components shown. HD-973P Series Multi-Level Parking Lift P/N 5900076 — Rev. B3 — January 2024...
  • Page 21 Posts and Runways can shift or even fall. If they fall on a person, they could cause severe injury. HD-973P Series Multi-Level Parking Lift P/N 5900076 — Rev. B3 — January 2024...
  • Page 22 Using a Forklift or Shop Crane, carefully move each Post to the inside corners of the Chalk Line Guides. Do not stand up the Posts yet; some of the following procedures are easier to complete if the Posts are laying on the ground. HD-973P Series Multi-Level Parking Lift P/N 5900076 — Rev. B3 — January 2024...
  • Page 23 Make sure you have the correct Crosstubes for the Platform on which you are working. With the Posts on the ground, slide the Crosstubes into place. HD-973P Series Multi-Level Parking Lift P/N 5900076 — Rev. B3 — January 2024...
  • Page 24 Gussets. They are different from the Safety Locks in that when the Cables are taut (which they are during normal operation), they hold the Slack Safeties away from the Ladder so that the Slack HD-973P Series Multi-Level Parking Lift P/N 5900076 — Rev. B3 — January 2024...
  • Page 25 Platform in danger. Slots are created by the Slide Blocks on the Crosstube Gusset. Front and Side views combined. Not to scale. Not all components are shown. HD-973P Series Multi-Level Parking Lift P/N 5900076 — Rev. B3 — January 2024...
  • Page 26 The other hole in the Top Cap is for the Lifting Cable that is routed to the top of the Post, which is done later in the installation. Install the remaining Top Caps the same way. HD-973P Series Multi-Level Parking Lift P/N 5900076 — Rev. B3 — January 2024...
  • Page 27 Once both Crosstubes are in position, all Primary Safeties are engaged, and the Slack Safeties have been disengaged, you can continue with the installation. Repeat Steps 1 through 3 for the other Platform. HD-973P Series Multi-Level Parking Lift P/N 5900076 — Rev. B3 — January 2024...
  • Page 28 Slot, your Safety Locks will not function correctly, which is a danger to anyone under the Platform that is holding a Vehicle or around it. HD-973P Series Multi-Level Parking Lift P/N 5900076 — Rev. B3 — January 2024...
  • Page 29 Do not use Shims and/or Anchor Bolt to Shim more than 1/2 an inch. You can order 2-inch Shim Plates for extreme cases. Do not anchor the Posts at this point. HD-973P Series Multi-Level Parking Lift P/N 5900076 — Rev. B3 — January 2024...
  • Page 30 Platform. Pull Box and Side Sheaves are for Upper Platform only. Not to scale. Not all components shown. HD-973P Series Multi-Level Parking Lift P/N 5900076 — Rev. B3 — January 2024...
  • Page 31 Flex Tube (which holds the Air, Return, and Hydraulic Hoses). Top View. The opening on the inside of the Powerside Runway is for the Upper Platform only. Not to scale. Not all components shown. HD-973P Series Multi-Level Parking Lift P/N 5900076 — Rev. B3 — January 2024...
  • Page 32 Do not continue with the installation until you have visually confirmed that all four Safety Locks are engaged on each Platform. If they are not engaged, the Runways could move or fall, possibly causing personal injury or product damage. HD-973P Series Multi-Level Parking Lift P/N 5900076 — Rev. B3 — January 2024...
  • Page 33 In the following drawings, the Lifting Cables and Cable Sheaves are labeled A, B, C, and D. These letters are not on the label on the Threaded end. You must match the Cable letter with the length information. • The Lifting Cables for the HD-973P are: • The Lifting Cables for the HD-973PX are:  Upper Platform: ...
  • Page 34 The following drawing shows the routing for all four Lifting Cables on the Upper Platform. Cable Sheaves separated from Windows for clarity. Crosstubes not shown. Not to scale. HD-973P Series Multi-Level Parking Lift P/N 5900076 — Rev. B3 — January 2024...
  • Page 35 Post, it must be between where the Gusset Sheave will go and where the Slack Safety Sheave already is. If the Cable is not in this exact location, the Slack Safeties will not work correctly later. HD-973P Series Multi-Level Parking Lift P/N 5900076 — Rev. B3 — January 2024...
  • Page 36 Pull Box. With the Cables in place, reinstall the Double Cable Sheave in the Pull Box. The following drawing shows the Cable/Cable Sheave pairs in the Pull Box. HD-973P Series Multi-Level Parking Lift P/N 5900076 — Rev. B3 — January 2024...
  • Page 37 Routing Lifting Cables B and D is the same process as routing Lifting Cables A and C, just to Note the other two Posts and using a different set of Sheaves. Refer to the drawings in the previous section. HD-973P Series Multi-Level Parking Lift P/N 5900076 — Rev. B3 — January 2024...
  • Page 38 The following drawing shows the routing for all four Cables on the Lower Platform. Cable Sheaves separated from Windows for clarity. Crosstubes not shown. Not to scale. HD-973P Series Multi-Level Parking Lift P/N 5900076 — Rev. B3 — January 2024...
  • Page 39 Slack Safeties will not work correctly later. With the Lifting Cable in place, reinstall the Gusset Sheave and the Cable Lock Pin in Post A. HD-973P Series Multi-Level Parking Lift P/N 5900076 — Rev. B3 — January 2024...
  • Page 40 Routing Lifting Cables B and D is the same process as routing Lifting Cables A and C, just to the other two Posts and using a different set of Sheaves. Refer to the drawings in the previous section. HD-973P Series Multi-Level Parking Lift P/N 5900076 — Rev. B3 — January 2024...
  • Page 41 The Ferrule goes around the Rod and under the Threads. The Nut goes onto the Threads. Tighten the Nut. Remember that the Ferrule can only be used once; do not tighten the Nut until everything is ready. HD-973P Series Multi-Level Parking Lift P/N 5900076 — Rev. B3 — January 2024...
  • Page 42 The Air Line Elbow Connectors on the Crosstube Gussets come installed from the factory. Drawing not to scale. Some components not shown. Air Lines shown outside Steel Tubes for clarity. HD-973P Series Multi-Level Parking Lift P/N 5900076 — Rev. B3 — January 2024...
  • Page 43 Leave the Power Unit end of the Air Line hanging out of the Flex Tube opening for now. It will be connected to a Tee Fitting and the Pushbutton Air Valve later. Repeat Steps 1 through 5 for the other Platform. HD-973P Series Multi-Level Parking Lift P/N 5900076 — Rev. B3 — January 2024...
  • Page 44 Leave the Power Unit end of the Return Line hanging out of the Flex Tube opening for now. It will be connected to a Tee Fitting and then to the Power Unit later in the installation. Repeat Steps 1through 8 for the other Platform. HD-973P Series Multi-Level Parking Lift P/N 5900076 — Rev. B3 — January 2024...
  • Page 45 Hydraulic Hoses and Fittings on your Lift, making your new Lift inoperable. Your Lift is shipped with clean components; however, BendPak strongly recommends that you take a secondary precaution to clean all Hydraulic Hoses and Fittings prior to making connections. It is better and less costly to take these extra steps now so that you do not need to take your Lift out of service later fixing issues that could have been prevented at the time of installation.
  • Page 46 Always promptly clean any Hydraulic Fluid spills. If a leak is the source of the spill, lockout the Lift to prevent use until the Hydraulic System is repaired. HD-973P Series Multi-Level Parking Lift P/N 5900076 — Rev. B3 — January 2024...
  • Page 47 Valve and the ORB end attaches to the Power Unit. One Fitting total. The figure on the following page details the Hydraulic Hose routing on the Lift. HD-973P Series Multi-Level Parking Lift P/N 5900076 — Rev. B3 — January 2024...
  • Page 48 The figure below displays the Hydraulic Hose and its connectors in more detail. Not all components are shown. Not to scale. HD-973P Series Multi-Level Parking Lift P/N 5900076 — Rev. B3 — January 2024...
  • Page 49 Depending on your Power Unit, the connector locations may be different. Use the drawing below to identify your layout and then attach your Hydraulic Hoses and Return Line appropriately. HD-973P Series Multi-Level Parking Lift P/N 5900076 — Rev. B3 — January 2024...
  • Page 50 Attach the Safety Shutoff Bar to the Mounting Plate using a M10 x 38 mm Hex Bolt and a M10 x 1.5 Nylock Nut on each end. Go to the middle of the Runways, underneath where the two Aluminum Decks meet. HD-973P Series Multi-Level Parking Lift P/N 5900076 — Rev. B3 — January 2024...
  • Page 51 This section describes how to install, but not make the connections to, the Power Unit for your Lift. An Electrician is not needed to install the Power Unit; one is required to connect the Power Unit to its power source. HD-973P Series Multi-Level Parking Lift P/N 5900076 — Rev. B3 — January 2024...
  • Page 52 If you are going to install the Flex Tube Bracket Plate and/or the Zero Angle Bracket at the same time as the Power Unit, now is the time to put those into place. The Power Unit is heavy. BendPak recommends having one person hold the Power Unit while another person bolts it into place.
  • Page 53 Connect the Flex Tube Angle Plate to the Flex Tube Bracket so that the holes for the Flex Tubes are best positioned for connecting the Return Line, the Air Line, and the Hydraulic Hose. HD-973P Series Multi-Level Parking Lift P/N 5900076 — Rev. B3 — January 2024...
  • Page 54 Repeat Steps 1 through 7 for the Figure details Flex Tubes attached to the other Platform using Power Post Angle Plate. Not drawn to scale. the short Flex Tube. HD-973P Series Multi-Level Parking Lift P/N 5900076 — Rev. B3 — January 2024...
  • Page 55 The following drawing shows the Zero Angle Bracket and where it connects. The following drawing shows the Pushbutton Air Valve and its connections. Power Unit not shown. Front view. HD-973P Series Multi-Level Parking Lift P/N 5900076 — Rev. B3 — January 2024...
  • Page 56 Double check to make sure you are attaching the Air Line to the Pushbutton Air Valve. For the customer-supplied air pressure, a minimum of 75 PSI. HD-973P Series Multi-Level Parking Lift P/N 5900076 — Rev. B3 — January 2024...
  • Page 57 Return Line to the Power Unit and not the Air Line. Do not attach the Air Line to the Power Unit by mistake. HD-973P Series Multi-Level Parking Lift P/N 5900076 — Rev. B3 — January 2024...
  • Page 58 Take the ORB x NPT Nipple Fitting and attach the ORB end to the Hydraulic Pressure Out on the Power Unit and attach the Platform Selector Valve to the NPT end. HD-973P Series Multi-Level Parking Lift P/N 5900076 — Rev. B3 — January 2024...
  • Page 59 Double check that you have the correct Hydraulic Hose. Find the Hydraulic Hose for the Lower Platform and connect it to the Left side of the Valve. 5585173 5585312 5585503 HD-973P Series Multi-Level Parking Lift P/N 5900076 — Rev. B3 — January 2024...
  • Page 60 If your organization has Lockout/Tagout policies, make sure to implement them after connecting to a power source. Important electrical information: • Improper electrical installation can damage the motor; this is not covered under warranty. HD-973P Series Multi-Level Parking Lift P/N 5900076 — Rev. B3 — January 2024...
  • Page 61 Double check to verify the Hydraulic Fluid Reservoir has an adequate supply of fluid. ⚠ WARNING Do not run the Lift without an adequate supply of Hydraulic Fluid; you will damage the Power Unit. HD-973P Series Multi-Level Parking Lift P/N 5900076 — Rev. B3 — January 2024...
  • Page 62 High running electrical current that exceeds the motor’s full load amps (FLA) rating may result in permanent damage to the motor. BendPak strongly recommends you not exceed the rated duty cycle of the Lift’s motor. HD-973P Series Multi-Level Parking Lift...
  • Page 63 Concrete or Anchor Bolts do not meet these specifications, it could lead to product damage, Vehicle damage, personal injury, or even death. BendPak Lifts are supplied with installation instructions and concrete fasteners meeting the criteria as prescribed by the American National Standard “Automotive Lifts – Safety Requirements for Construction, Testing, and Validation”...
  • Page 64 Expansion Sleeve does not press against the Concrete with as much force, again resulting in less holding strength. BendPak recommends using a vacuum to clean the hole. You can also use a wire brush, hand pump, or compressed air; just make sure to thoroughly clean each hole.
  • Page 65 Powerside Posts. The Crossbeams increase the structural stability to your Lift. The figure below details the orientation of the Crossbeams. Side view. Runways not shown. Not drawn to scale. Not all components shown. HD-973P Series Multi-Level Parking Lift P/N 5900076 — Rev. B3 — January 2024...
  • Page 66 Side view. Runway Covers are pushed up into place under the Runway. Adjust the Covers until the Lifting Cables and the Hydraulic Cylinder are covered. Repeat Steps 1 and 2 for the remaining Runways. HD-973P Series Multi-Level Parking Lift P/N 5900076 — Rev. B3 — January 2024...
  • Page 67 Ramp and Runway tubes and secure the Drive-up Ramp in place with a Rotor Clip on each end of the Pin; repeat for the other Drive-up Ramp. HD-973P Series Multi-Level Parking Lift P/N 5900076 — Rev. B3 — January 2024...
  • Page 68 Installing the Anti-Slip Tape The Anti-Slip Tape (SKU 5930195) is provided in two rolls measuring 6 in. x 24 ft. (152 mm x 7.3m). BendPak suggests cutting the Tape into eight equal lengths 72 in (1,829 mm) long each. IMPORTANT! Surface preparation is important.
  • Page 69 Platforms are resting on their Safety Locks and the power source has been completely disconnected. If your organization has Lockout/Tagout policies, make sure to implement them after connecting to the power source. HD-973P Series Multi-Level Parking Lift P/N 5900076 — Rev. B3 — January 2024...
  • Page 70 Lubricate the inside of all four Lift Posts (where the Crosstubes travel) with a white lithium grease. Raise and lower both platforms to aid in distributing the lubrication. Clean and remove any excess lubricant from around the Lift and on the Lift surfaces. HD-973P Series Multi-Level Parking Lift P/N 5900076 — Rev. B3 — January 2024...
  • Page 71 Hydraulic Fluid in the reservoir. If your Lift is still moving erratically or making odd noises after bleeding the Hydraulic System, refer to Troubleshooting for more information. HD-973P Series Multi-Level Parking Lift P/N 5900076 — Rev. B3 — January 2024...
  • Page 72 Test the Lift BendPak strongly recommends doing an Operational Test of your Lift with a standard Vehicle on each Platform before starting normal service (a typical Vehicle is not required but is recommended). During the Operational Test, watch the Lift and its components and check for proper installation and operation.

  • Page 73: Operation

    Double check you have everything you need out of the Vehicle before raising the Lift. Make sure the Vehicle is not overbalanced on either end or either side. HD-973P Series Multi-Level Parking Lift P/N 5900076 — Rev. B3 — January 2024...
  • Page 74 Platforms. If there is something in the way, stop the Lift and move it out of the way. Watch the Lift carefully as it raises and lowers. HD-973P Series Multi-Level Parking Lift P/N 5900076 — Rev. B3 — January 2024...
  • Page 75 When the Platform arrives at the desired height, move the platform Up a small amount more, then release the Up button and press and hold the Lowering Handle. The Platform will lower onto the most recently passed Safety Lock. HD-973P Series Multi-Level Parking Lift P/N 5900076 — Rev. B3 — January 2024...
  • Page 76 Lowering Handle. Once downward movement stops, release the Lowering Handle. Verify that the Lower Platform is on all four Locking positions before driving a Vehicle under it. HD-973P Series Multi-Level Parking Lift P/N 5900076 — Rev. B3 — January 2024...
  • Page 77 When the Upper Platform has descended into position on the Stop Blocks, release the Pushbutton Air Valve and the Lowering Handle. Remove the Tire Chocks, then carefully drive the Vehicle off the Platforms. HD-973P Series Multi-Level Parking Lift P/N 5900076 — Rev. B3 — January 2024...

  • Page 78: Maintenance

    Do not operate your Lift if you find maintenance issues; instead, take the Lift out of service, then contact your dealer, visit bendpak.com/support, email support@bendpak.com, or call (800) 253-2363 option 7 then 4. HD-973P Series Multi-Level Parking Lift P/N 5900076 — Rev. B3 — January 2024...
  • Page 79 Visually check for any broken wires. One way to check for crown breaks is to run a cloth along the rope to check for snags. d. With an awl, probe between wires and strands and raise any wires that appear loose. HD-973P Series Multi-Level Parking Lift P/N 5900076 — Rev. B3 — January 2024...
  • Page 80 Fasteners Torque Chart HD-973P Series Multi-Level Parking Lift P/N 5900076 — Rev. B3 — January 2024...

  • Page 81: Troubleshooting

    Crosstubes using white lithium grease. If the Lift is new, a break-in period may be needed; run the Lift several times each day. If the noises persist, contact BendPak Support. If you continue to have issues with your Lift, take it out of service, then contact your dealer, go to bendpak.com/support, email...

  • Page 82: Wiring Diagrams

    5585312 (208-240, 1 Ph, 50/60Hz. 3 5585503 (208-230, 1 Ph, 50/60Hz. 2 HP) 5585512 (208-230/400/460VAC, 3 Ph., 50/60 Hz. 4 HP.) 5585173 (110VAC, 1 Ph, 60Hz., 2 HP) HD-973P Series Multi-Level Parking Lift P/N 5900076 — Rev. B3 — January 2024...
  • Page 83 This section describes wiring details for the Microswitch(es), depending on your chosen Power Unit. Single Phase: Three Phase: HD-973P Series Multi-Level Parking Lift P/N 5900076 — Rev. B3 — January 2024...

  • Page 84: Labels

    Labels HD-973P Series Multi-Level Parking Lift P/N 5900076 — Rev. B3 — January 2024...
  • Page 85 HD-973P Series Multi-Level Parking Lift P/N 5900076 — Rev. B3 — January 2024...
  • Page 86 HD-973P Series Multi-Level Parking Lift P/N 5900076 — Rev. B3 — January 2024...

  • Page 87: Parts Drawings

    Parts Drawings HD-973P Series Multi-Level Parking Lift P/N 5900076 — Rev. B3 — January 2024...
  • Page 88 HD-973P Series Multi-Level Parking Lift P/N 5900076 — Rev. B3 — January 2024...
  • Page 89 HD-973P Series Multi-Level Parking Lift P/N 5900076 — Rev. B3 — January 2024...
  • Page 90 HD-973P Series Multi-Level Parking Lift P/N 5900076 — Rev. B3 — January 2024...
  • Page 91 HD-973P Series Multi-Level Parking Lift P/N 5900076 — Rev. B3 — January 2024...
  • Page 92 HD-973P Series Multi-Level Parking Lift P/N 5900076 — Rev. B3 — January 2024...
  • Page 93 HD-973P Series Multi-Level Parking Lift P/N 5900076 — Rev. B3 — January 2024...
  • Page 94 HD-973P Series Multi-Level Parking Lift P/N 5900076 — Rev. B3 — January 2024...
  • Page 95 HD-973P Series Multi-Level Parking Lift P/N 5900076 — Rev. B3 — January 2024...
  • Page 96 HD-973P Series Multi-Level Parking Lift P/N 5900076 — Rev. B3 — January 2024...
  • Page 97 HD-973P Series Multi-Level Parking Lift P/N 5900076 — Rev. B3 — January 2024...
  • Page 98 HD-973P Series Multi-Level Parking Lift P/N 5900076 — Rev. B3 — January 2024...
  • Page 99 HD-973P Series Multi-Level Parking Lift P/N 5900076 — Rev. B3 — January 2024...
  • Page 100 HD-973P Series Multi-Level Parking Lift P/N 5900076 — Rev. B3 — January 2024...
  • Page 101 HD-973P Series Multi-Level Parking Lift P/N 5900076 — Rev. B3 — January 2024...
  • Page 102 HD-973P Series Multi-Level Parking Lift P/N 5900076 — Rev. B3 — January 2024...
  • Page 103 HD-973P Series Multi-Level Parking Lift P/N 5900076 — Rev. B3 — January 2024...
  • Page 104 HD-973P Series Multi-Level Parking Lift P/N 5900076 — Rev. B3 — January 2024...
  • Page 105 HD-973P Series Multi-Level Parking Lift P/N 5900076 — Rev. B3 — January 2024...
  • Page 106 HD-973P Series Multi-Level Parking Lift P/N 5900076 — Rev. B3 — January 2024...
  • Page 107 HD-973P Series Multi-Level Parking Lift P/N 5900076 — Rev. B3 — January 2024...
  • Page 108 HD-973P Series Multi-Level Parking Lift P/N 5900076 — Rev. B3 — January 2024...

  • Page 109: Maintenance Log

    Maintenance Log _____________________________________________________________________________________ HD-973P Series Multi-Level Parking Lift P/N 5900076 — Rev. B3 — January 2024...
  • Page 110 Maintenance Log _____________________________________________________________________________________ HD-973P Series Multi-Level Parking Lift P/N 5900076 — Rev. B3 — January 2024...
  • Page 111 Maintenance Log HD-973P Series Multi-Level Parking Lift P/N 5900076 — Rev. B3 — January 2024...
  • Page 112 1645 Lemonwood Drive Santa Paula, CA, 93060 USA bendpak.com © 2024 BendPak Inc. All rights reserved.

This manual is also suitable for:

Hd-973px

Table of Contents