Black+Decker RT18 Manual
  1. Manuals
  2. Brands
  3. Black+Decker Manuals
  4. Power Tool
  5. RT18
  6. Manual

Black+Decker RT18 Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

RT18
RT18KA
English
4

Advertisement

Table of Contents
loading

Related Manuals for Black+Decker RT18

Summary of Contents for Black+Decker RT18

  • Page 1 RT18 RT18KA English...
  • Page 2 FIG. A FIG. B FIG. C FIG. D FIG. E...
  • Page 3 FIG. F FIG. G FIG. H FIG. I f The illustratrions are for representative purposes only, they can differ from actual product.
  • Page 4 ACCESSORIES Illustration Description Shape Quantity Cut Off wheel 15/16” Sanding disc 3/4” Round 1/2” Diameter Drum sander 1/8” Shank Sanding band 1/2” Felt polishing wheel 1” Felt polishing wheel 1/2” Felt polishing tip 3/8” Assorted Grinding stones Assorted Brass brush 1/4”...
  • Page 5 ACCESSORIES Illustration Description Shape Quantity Diamond bit Cylinder Multi-purpose bit 1/8” Cylinder Screw mandrel 3/32” Screw mandrel 1/8” Mandrel for felt wheels 1/8” Dressing stone 3/8” x 3/8” x 1” Collet (installed in tool) 1/8” Collet 3/32” Collet 1/16” Collet wrench Depth gauge...

  • Page 6: General Safety Rules

    6 • ENGLISH c. Do not expose power tools to rain or wet conditions. RT18/RT18KA Water entering a power tool will increase the risk of TOTARY TOOL electric shock. d. Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool.
  • Page 7 BLACK+DECKER the warranty will not be valid. collet or chuck. If the mandrel is insufficiently held and/ or the overhang of the wheel is too long, the mounted 7.

  • Page 8: Further Safety Instructions For All Operations

    8 • ENGLISH If power tool or accessory is dropped, inspect for could snag your clothing, pulling the accessory into your damage or install an undamaged accessory. After body. inspecting and installing an accessory, position s. Regularly clean the power tool’s air vents. The yourself and bystanders away from the plane of the motor’s fan will draw the dust inside the housing and rotating accessory and run the power tool at...

  • Page 9: Extension Cords

    ENGLISH • 9 from the material (which is the same direction wheel is in motion otherwise kickback may occur. as the chips are thrown). Feeding the tool in the Investigate and take corrective action to eliminate the wrong direction causes the cutting edge of the bit cause of wheel pinching or snagging.
  • Page 10 10 • ENGLISH intended to be mounted on a threaded mandrel, Minimum gage for cord sets critical dimensions and other data shall be given in order to prevent the mandrel end from touching Volts Total length of cord in feet the bottom of the hole of the abrasive product 120V 0 - 25...

  • Page 11: Maintenance

    ENGLISH • 11 counter-clockwise. 2. Thread screw (19) in the bottom of the hang bar rod (20) 2. Before replacing collet nut, check to make sure into the appropriate mounting hole (21) in the C-clamp (Fig. H). the 1/8” collet is installed in the motor shaft. Notes: Note: Do not over tighten.

  • Page 12: Protecting The Environment

    Complete product range may not be available in all hazardous condition leading to possible serious injury. It countries. will also void the warranty. f Contact your local BLACK+DECKER dealers for range Important! To assure product Safety and reliability, availability. repairs, maintenance and adjustment (other than those...

This manual is also suitable for:

Rt18ka

Table of Contents