Glass Cleaning; Installation Of Logs And Burner Lava Rock; Maintenance - Vermont Castings RFS22 Installation Instructions & Homeowner's Manual

GLASS CLEANING

It will be necessary to clean the glass periodically.
During start-up condensation, which is normal, forms on
the inside of the glass and causes lint, dust and other
airborne particles to cling to the glass surface. Also
initial paint curing may deposit a slight film on the glass.
It is therefore recommended that the glass be cleaned
two or three times with a non-ammonia household
cleaner and warm water (we recommend gas fireplace
glass cleaner). After that the glass should be cleaned
two or three times during each heating season
depending on the circumstances present.
Clean glass after first two weeks of
operation.
INSTALLATION OF LOGS &
BURNER LAVA ROCK
RFS22 & RFS32
1 . Remove front glass. (See "Glass Removal" section)
2. Remove logs from packaging.
3. Place rear log (KR4) on rear bracket (ensure log is
seated properly, leveled and centered to the unit), so it
will not move from side to side and it is firmly positioned
on the bracket.
4. Slip front ember log (KR1) down in the front deflector.
5. Place front left log (KR2) on top burner, left side. Use
log's bottom holes to locate it into the left bracket log
locator studs.
6. Place front right log (KR3) on top of burner, right side.
Use log's bottom holes to locate it into the right bracket
log locator studs.
7. Place small lava rocks and ember material on top of
burner. (See Fig. 16 for proper location).
8. Place top left log (KR5) onto locator notches. Ensure
log is secure.
9. Place top right log (KR6) onto locator notches. Ensure
log is secure.
Top logs must be placed properly into
notches
KR5
KR2
KR6
KR4
KR3
KR1
Fig. 16
Burner Lava Rock Placement
RFS42
1 .Remove Bay Window assembly and Glass Frame (see
"Glass Frame Removal" section).
2. Remove logs from packaging.
3. Place rear log (SR4) on rear bracket . Ensure log is
seated properly, leveled and centered to the unit), so it
will not move from side to side and it is firmly positioned
on the bracket.
4. Slip front ember log (SR1) down in the front deflector.
5. Place front left log (SR2) on on top of burner, left side.
Use log's bottom holes to locate it into the left bracket log
locator studs.
6. Place front right log (SR3) on on top of burner,right side.
Use log's bottom holes to locate it into the right bracket
log locator studs.
7. Place burner lava rock on top of burner. (See Fig. 17 for
proper location).
8. Place top right log (SR6) onto locator notches. Ensure
log is secure.
9. Place top left log (SR5) onto locator notches. Ensure log
is secure.
SR5
SR2
1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8
1 2 3
Burner Lava Rock Placement
1 2 3
1. It is important to keep the burner and the burner
compartment clean. This must be done periodically, at
least once per season. (See Cleaning Procedure).
2. Clean the brass trim using a soft clean cloth, slightly
dampened with lemon oil and buff with a soft clean
cloth. Do NOT use brass polish or household cleaners
as these products will damage the brass trim. Lemon
oil can be obtained at supermarkets or hardware
stores.
3. The optional FK24 Fan requires periodic cleaning.
Check the fan and the area around the fan assembly
and wipe or vacuum at least once per month during the
operating season.
4. Contact your local representative to arrange an annual
service program.
- 10 -
SR6
SR4

MAINTENANCE

SR3
SR1
Fig. 17