Advertisement
Quick Links
740B Clifty Drive • Madison, Indiana 47250 • 812-574-7777
Item Description
A
Roof Half (Passenger)
B
Roof Half (Driver)
C
Tube Clamps
B
Qty (10)
Qty (6)
Read instructions and view illustrations before beginning.
Need help with your installation?
sales@superatv.com
1-812-574-7777
Thank You
© 2011 SuperATV.com. All Rights Reserved.
If installing on Bobcat 3400, modifications are required.
M6-1.0 x 20mm Lg. PHMS
M6 Fender Washer
www.superatv.com
8:00am - 9:00pm EST M-Th
8:00am - 7:00pm EST Friday
9:00am - 2:00pm EST Saturday
For Choosing
INSTALLATION INSTRUCTIONS
Polaris Ranger Plastic Roof
Qty
1
1
8
Qty (10)
Qty (6)
Liability Statement
SuperATV's products are designed to best fit users ATV/UTV under stock conditions.
Adding, modifying, or fabricating any factory, or aftermarket, parts will void any
warranty provided by SuperATV and is not recommended. SuperATV's products
could interfere with other aftermarket accessories. If user has aftermarket products
on machine, contact SuperATV to verify that they will work together.
Although SuperATV has thousands of satisfied customers, user should be aware
that installing lift kits, long travel, or suspension kits, tires, etc will change the ride
of machine and may increase maintenance and part wear. Operating any off-road
machine while, or after, consuming alcohol and/or drugs increases risk of bodily
harm or death. No warranty or representation is made as to this product's ability to
protect user from severe injury or death. SuperATV urges operators and occupants
to wear a helmet and appropriate riding gear at all times.
By purchasing and installing SuperATV products, user agrees that should damages
occur, SuperATV will not be held responsible for loss of time, use, labor fees,
replacement parts, or freight charges. SuperATV, nor any 3rd party, will not be held
responsible for any direct, indirect, incidental, special, or consequential damages
that result from any product purchased from SuperATV. The total liability of seller to
user for all damages, losses, and causes of action, if any, shall not exceed the total
purchase price paid for the product that gave rise to the claim.
SuperATV will warranty only parts provided by SuperATV. Any damage or problems
with OEM housings, bearings, seals, or other manufacturers products will not be
covered by SuperATV. SuperATV parts and products are not warrantied if item was
not installed properly, misused, or modified.
C
A
M6-1.0 Nylock Nut
M6 Flat Washer
Rev IN-PR-P-RAN-09 3/3/2014
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for SuperATV PR-P-RAN-09
Summary of Contents for SuperATV PR-P-RAN-09
- Page 1 By purchasing and installing SuperATV products, user agrees that should damages 9:00am - 2:00pm EST Saturday occur, SuperATV will not be held responsible for loss of time, use, labor fees, replacement parts, or freight charges. SuperATV, nor any 3rd party, will not be held...
- Page 2 Do not tighten hardware completely unless noted. 1. Place Roof Half (B) on top of machine followed by Roof Half (A). If installing on Bobcat 3400 models, proceed to page 3. 2. Place Tube Clamps (C) around Roll Bar. Attach Roof (A)(B) to Tube Clamps (C) using (6) each M6-1.0 x 20mm Lg.
- Page 3 Fig. 2 Drill and secure M6 x 20mm Lg. PHMS M6 Nylock Nut M6 Flat Washers Bobcat 3400 If installing on Bobcat 3400 models, forward mounting locations will require modification. See below. 1. Measure over, approximately 2” towards center of machine, from original mounting hole. Original front mounting locations will not work;...
Need help?
Do you have a question about the PR-P-RAN-09 and is the answer not in the manual?
Questions and answers