Roland JUPITER-X Reference Manual page 45

Parameter Value
[1] knob [2] knob
USB-MIDIThru OFF, ON
USB Driver GENERIC, VENDOR
Remote Kbd OFF, ON
Local Sw OFF, ON
Device ID 17–32
MIDI Tx
Tx PC OFF, ON
Tx Bank OFF, ON
Tx Edit OFF, ON
MIDI Rx
Rx PC OFF, ON
Rx Bank OFF, ON
Rx Exclusive OFF, ON
MIC IN
Mic In Gain -24.0–+24.0 [dB]
Mic Power OFF, ON
NS Switch OFF, ON
NS Threshold -96–0 [dB]
NS Release 0–127
CompSwitch OFF, ON
CompAttack 0.1, 1, 2, ..., 100 [ms]
CompRelease 10, 20, ..., 1000 [ms]
CompThreshold -60–0 [dB]
1: 1, 2: 1, ...4: 1, 8: 1,
CompRatio
16: 1, 32: 1, INF: 1
CompKnee 0–30 [dB]
-24.0, -23.5, ... 0,
CompOutGain
..., +24.0 [dB]
Rev Send Lev 0–127
Cho Send Lev 0–127
Dly Send Lev 0–127
Mic Thru OFF, ON
CONTROLLER
Velocity REAL, 1–127
LIGHT, MEDIUM,
Velo Crv
HEAVY
Explanation
Specifies whether MIDI messages received at
the USB COMPUTER port/MIDI IN connector are
retransmitted without change from the MIDI
OUT connector/USB COMPUTER port (ON) or
are not retransmitted (OFF).
Specifies the USB driver setting.
Turn this "ON" if you want to use an external
MIDI keyboard instead of the JUPITER-X's
keyboard. In this case, the MIDI transmit
channel of the external MIDI keyboard does
not matter.
Normally you will leave this "OFF. "
Turns on/off the connection between the
controller section (keyboard, PITCH, MODE,
panel buttons and sliders, pedals, etc.) and the
internal sound engine.
When transmitting and receiving system
exclusive messages, the device ID numbers of
both devices must match.
Specifies whether program change messages
will be transmitted (ON) or not be transmitted
(OFF).
Specifies whether bank select messages will be
transmitted (ON) or not be transmitted (OFF).
Specify whether changes you make in the
settings of a program will be transmitted as
system exclusive messages (ON), or will not be
transmitted (OFF).
Specifies whether program change messages
will be received (ON) or not be received (OFF).
Specifies whether bank select messages will be
received (ON) or not be received (OFF).
Specifies whether system exclusive messages
will be received (ON) or not be received (OFF).
Adjusts the input level of the MIC IN jack.
If this is "ON, " plug-in power (5 V) is supplied to
the MIC IN jack.
Switches the noise suppressor on/off.
The noise suppressor is a function that
suppresses noise during periods of silence.
Adjusts the volume at which noise suppression
starts to be applied.
Adjusts the time from when noise suppression
starts until the volume reaches 0.
Specifies whether the mic compressor (a
compressor applied to the mic input) is used
(ON) or not used (OFF).
Specifies the time from when the input to the
mic compressor exceeds the Comp Thres level
until the volume is compressed.
Specifies the time from when the input to the
mic compressor falls below the Comp Thres
level until compression is no longer applied.
Specifies the level at which the mic compressor
starts applying compression.
Specifies the compression ratio for the mic
compressor.
Smooths the transition until the mic
compressor starts to be applied.
Higher values produce a smoother transition.
Specifies the output volume of the mic
compressor.
Specifies the amount of reverb that is applied
to the mic input.
Specifies the amount of chorus that is applied
to the mic input.
Specifies the amount of delay that is applied to
the mic input.
If you want the mic to be cut when the vocoder
is off, turn this "OFF. "
Specifies the velocity value that is transmitted
when you play the keyboard.
Specifies "Strength" for keyboard touch.
Parameter Value
[1] knob [2] knob
Velo Offset -10–+9
Knob Mode DIRECT, CATCH
Aft Sens 0–100
BUTTON Func
Source SCENE, SYS
For the values,
refer to "List of
S1 Func functions that can
be assigned to the
controllers"
LATCH,
S1 Mode
MOMENTARY
For the values,
refer to "List of
S2 Func functions that can
be assigned to the
controllers"
LATCH,
S2 Mode
MOMENTARY
For the values,
refer to "List of
S3 Func functions that can
be assigned to the
controllers"
LATCH,
S3 Mode
MOMENTARY
SLIDER Func
SL1 Source SCENE, SYS
For the values,
refer to "List of
SL1 functions that can
be assigned to the
controllers"
SL2 Source SCENE, SYS
For the values,
refer to "List of
SL2 functions that can
be assigned to the
controllers"
PEDAL Func
Hold Source SCENE, SYS
For the values,
refer to "List of
Hold functions that can
be assigned to the
controllers"
STANDARD,
Hold Pole
REVERSE
Ctrl Source SCENE, SYS
For the values,
refer to "List of
Ctrl functions that can
be assigned to the
controllers"
Wheel Func
Wheel1 Source SCENE, SYS
For the values,
refer to "List of
Wheel1 functions that can
be assigned to the
controllers"
Settings for the Entire Unit
Explanation
Adjusts the keyboard velocity curve.
Specifies whether the parameter value
corresponding to a controller is immediately
updated when you operate that controller
(DIRECT) or only after the controller reaches
the same position as the parameter's current
value (CATCH).
Specifies the aftertouch sensitivity.
Specifies whether the functions assigned
to these buttons follows the settings of the
currently selected scene (SCENE) or the system
settings (SYS).
Specifies the function assigned to the [S1]
button.
Specifies how the button operates.
Specifies the function assigned to the [S2]
button.
Specifies how the button operates.
Specifies the function assigned to the [S3]
button.
Specifies how the button operates.
Specifies whether the function assigned to the
SL1 slider follows the setting of the currently
selected scene (SCENE) or the system setting
(SYS).
Specifies the function assigned to the [SL1]
slider.
Specifies whether the function assigned to the
SL2 slider follows the setting of the currently
selected scene (SCENE) or the system setting
(SYS).
Specifies the function assigned to the [SL2]
slider.
Specifies whether the function assigned to the
pedal connected to the HOLD jack follows the
setting of the currently selected scene (SCENE)
or the system setting (SYS).
Specifies the function assigned to the pedal
connected to the HOLD jack.
Specifies the polarity of the pedal connected to
the HOLD jack.
Specifies whether the function assigned to the
pedal connected to the CTRL jack follows the
setting of the currently selected scene (SCENE)
or the system setting (SYS).
Specifies the function assigned to the pedal
connected to the CTRL jack.
Specifies whether the function assigned to
the [WHEEL 1] wheel follows the setting of the
currently selected scene (SCENE) or follows the
system setting (SYS).
Specifies the function assigned to the [WHEEL
1] wheel.
45