Saving The Tone Settings Of Each Part (Part1-4 Tone); Initializing The Scene; (Scene Initialize); Initializing A Tone (Tone Initialize) - Roland JUPITER-X Reference Manual

Saving the Tone Settings of Each Part
(PART1–4 TONE)
Here's how to save the tone settings of each part.
1 .
Press the [SCENE] button, and then press the
button .
2 .
Use the [1] knob to select
to which the tone you're saving is assigned), and then
press the [ENTER] button .
3 .
Use the [1] knob or [2] knob
destination, and then press the
If you want to rename the tone that you're saving, use the
[<] [>] buttons to move the cursor, and use the
specify the character.
4 .
Press the [ENTER] button .
A confirmation message appears.
If you decide to cancel, press the
5 .
To execute, press the

Initializing the Scene

Here's how to initialize the scene settings.
The first tone of the presets is selected as the tone for each part.
1 .
Press the [SCENE] button, and then press the
button .
2 .
Use the [1] knob to select
then press the [ENTER]
Initializing a Tone
(TONE INITIALIZE)
Here's how to initialize the tone of the current part. The initialized state
differs depending on the model that is selected for that part.
You can't change the model later. You must first select a tone of the
model that you want to edit, and then execute Tone Initialize to
initialize it.
1 .
Press the [SCENE] button, and then press the
button .
2 .
Use the [1] knob to select
press the [ENTER] button .
Editing the System Settings
1 .
Press the [MENU] button .
2 .
Use the [1] knob to select
the [ENTER] button .
You can also make this selection by using the
buttons instead of the [1]
3 .
Use the PAGE [<] [>] buttons
you want to edit .
SYSTEM
Make basic device settings for the JUPITER-X.
&
"System Parameter List"
[WRITE]
"PART* TONE" (* is the part
to select the save-
[ENTER] button .
[2] knob
[EXIT] button.
[ENTER] button .

(SCENE INITIALIZE)

[WRITE]
"SCENE INITIALIZE,"
button .
[WRITE]
"TONE INITIALIZE," and then
(System)
"SYSTEM," and then press
PAGE [ ] [ ]
knob.
to select the page that
(p. 44)
SYSTEM EFFECT: Cho
Choose whether the chorus effect settings are fixed at the
system settings, or are specified by each scene.
If "Source" is set to
edit the effect.
&
"Editing a Scene
SYSTEM EFFECT: Dly
Choose whether the delay effect settings are fixed at the
system settings, or are specified by each scene.
If "Source" is set to
edit the effect.
&
"Editing a Scene
SYSTEM EFFECT: Rev
PAGE
to
Choose whether the reverb effect settings are fixed at the
system settings, or are specified by each scene.
If "Source" is set to
edit the effect.
&
"Editing a Scene
SYSTEM EQ / COMP
Edit the equalizer and compressor settings.
SYSTEM COLOR SET
Specify the color that is assigned to the buttons.
&
"System Parameter List"
4 .
Use the [1] knob
[2] knob to change the setting .
For details, refer to
5 .
and If you want to save the settings, perform the system
write operation .
Saving the System Settings
Here's how to save the system settings.
1 .
In the SYSTEM screen, press the
The SYSTEM WRITE screen appears.
If you decide to cancel, press the
MEMO
If the WRITE MENU screen appears, use the
select "SYSTEM, "
2 .
To execute, press the
Settings for the Entire Unit
"SCENE, " use the scene effect parameters to
" (p. 23)
(SCENE EDIT)
"SCENE, " use the scene effect parameters to
" (p. 23)
(SCENE EDIT)
"SCENE, " use the scene effect parameters to
" (p. 23)
(SCENE EDIT)
(p. 44)
to select the parameter and use the
"Parameter Guide" (PDF).
(System Write)
[WRITE]
[EXIT] button.
[1]
and then press the [ENTER] button.
[ENTER] button .
button .
or [2] knob to
43