Table of Contents
Advertisement
Quick Links
The length and width of the upper and lower bunk mattress and foundation are as follows :
Size
Twin
Full
Ensure thickness of upper and lower mattress and foundation combined does not exceed 9 ½"
and that the mattress is at least 5" below upper edge of guardrails.
Replacement parts, including additional guardrails, may be obtained from any
!
Follow the information on the warnings appearing on the upper bunk end structure
( 1 )
and on the carton. Do not remove warning label from bed.
Always use the recommended size mattresses or mattress support, or both,
( 2 )
to help prevent the likehood of entrapment or falls.
( 3 )
Surface of mattress must be at least 5 in. (127mm) below the upper edge of guardrails.
( 4 )
Do not allow children under 6 years of age to use the upper bunk.
( 5 )
Periodically check and ensure that the guardrail, ladder, and other component are
in their proper position, free from damage, and that all connectors are tight.
( 6 )
Do not allow horseplay on or under the bed and prohibit jumping on the bed.
Always use ladder for entering or leaving upper bunk.
( 7 )
( 8 )
Do not use substitute parts. Contact the manufacturer or dealer for replacement parts.
( 9 )
Use of a night light may provide added safety precaution for a child using the upper bunk.
(10)
Always use guardrails on both long sides of the upper bunk. If the bunk bed will be placed
next to the wall, the guardrail that runs the full length of the bed should be placed against
the wall to prevent entrapment between the bed and the wall.
(11)
The use of water or sleep flotation mattresses is prohibited.
(12)
STRANGULATION HAZARD : Never attach or hang items to any part of the bunk bed
that are not designed for use with the bed; for example, but not limited to, hooks, belts
and jump ropes.
(13)
Keep these instructions for future reference.
BUNK SAFETY WARNING
Size of Mattress and Foundation
Length
74"- 75"
74"- 75"
You must use only this size mattress.
This Bunk Bed uses a slat kit for mattress foundation.
Replacement Parts
Atlantic Furniture dealer
SAFETY WARNINGS
Width
37 ½"- 38 ½"
52"- 53"
Thickness
9 ½" max
9 ½" max
!
Page 1 of 9
Advertisement
Table of Contents
Related Manuals for Atlantic Furniture RICHLAND BUNK BED
Summary of Contents for Atlantic Furniture RICHLAND BUNK BED
- Page 1 This Bunk Bed uses a slat kit for mattress foundation. Replacement Parts Replacement parts, including additional guardrails, may be obtained from any Atlantic Furniture dealer SAFETY WARNINGS Follow the information on the warnings appearing on the upper bunk end structure ( 1 ) and on the carton.
- Page 2 Familiariz yourself with the different parts. Please note that you will require a Phillips head screwdriver and an Allen wrench. ATTENTION! If you receive a damaged or defective item, please contact Atlantic Furniture at service@atlanticfurniture.com 1-800-955-3726 / M-F 9:00-5:00 EST Adult Assembly Allen wrench...
- Page 3 PARTS LIST HARDWARE UPPER PANEL LOWER PANEL RIGHT SIDE RAIL LEFT SIDE RAIL LADDER STEP 1 1 BOX LADDER STEP 2 END CAP RIGHT POST LEFT POST SHORT RAIL FULL GUARD RAIL 3/4 GUARD RAIL 1 BOX LONG RAIL SLAT KIT TWIN 1 BOX SLAT KIT FULL LOWER BUNK 1 BOX...
- Page 4 STEP Attach the long rails (14) to the upper panels (02), using JCB M6 X 3 ” (B) and barrel nut (E). Tighten with the Allen wrench (M). JCB M6 X 3 ” Barrel Nut Allen wrench Adult Assembly STEP Attach the 3/4 guard rail (13) to the end cap (08), using Allen screw M6 X 2 ”...
- Page 5 STEP Lay the twin slat kit (15) onto the bed. Fix in place using wood screws provided in the slat kit box. FOR SLAT KIT ASSEMBLY follow assembly instructions included with slat kit. Adult Assembly Customer Supplied Phillips head screwdriver Install the full and 3/4 guard rail assembly (12)(13) to the upper panel, and fix in place using Allen screws(G).
- Page 6 Attach the right, left post (09)(10) to the short rail (11), using JCB M6 X 4” (A), and barrel nut (E). STEP Tighten with the Allen wrench (M). JCB M6 X 4” Barrel Nut Allen wrench Adult Assembly STEP Attach the extension full assembly to the lower panel (03) as shown below, using metal bracket (L), JCB M6 X 1 3/8”...
- Page 7 Attach the long rails (14) to the lower panel assemblies (03), using JCB M6 X 3 ” (B), and barrel nut (E). STEP Tighten with the Allen wrench (M). JCB M6 X 3 ” Barrel Nut Allen wrench Adult Assembly Lay the full lower bunk slat kit (16) onto the bed.
- Page 8 Insert metal pins (K) into the holes in top of the lower panels. Lift the upper panels onto the lower STEP panels as shown, and fit the metal pins into the holes in the bottom of the upper panel legs. Adult Assembly Metal Pins CAUTION...
- Page 9 LOWER INSIDE VIEW Congratulations ! Your Richland bunk bed is now ready for use. We recommend that you recheck that all screws are tight, and that all parts are secure before use. Periodically to ensure lasting Safety. Page 9 of 9...