Table of Contents
Advertisement
To reduce the risk of injury, the user must read and understand the operator's manual before using this product. If you do not
understand the warnings and instructions in the operator's manual, do not use this product.
Do not use E15 or E85 fuel (fuel containing ethanol greater than 10%) in this product. It is a violation of federal law and will
damage the engine and void your warranty. FUEL MIXTURE for this product is powered by a 2-cycle engine and requires
pre-mixing gasoline and 2-cycle oil in a 50:1 ratio. Pre-mix unleaded gasoline and 2-cycle engine oil in a clean container approved
for gasoline. DO NOT mix quantities larger than usable in a 30-day period.
SAvE ThESE iNSTRUCTiONS. This manual contains important safety precautions which should be read and understood before operating the product. Failure
to do so could result in serious injury. This manual should remain with the product.
Specifications, descriptions and illustrations in this manual are as accurate as known at the time of publication, but are subject to change without notice.
Made in China - REV 20200622
REGISTER YOUR PRODUCT ONLINE
at championpowerequipment.com
OPERATOR'S MANUAL
or visit championpowerequipment.com
WARNiNG
NOTiCE
Champion Power Equipment, Inc., Santa Fe Springs, CA USA
MODEL #100683
CURvED ShAfT TRiMMER
Advertisement
Table of Contents
Summary of Contents for Champion 100683
- Page 1 This manual should remain with the product. Specifications, descriptions and illustrations in this manual are as accurate as known at the time of publication, but are subject to change without notice. Made in China - REV 20200622 Champion Power Equipment, Inc., Santa Fe Springs, CA USA...
-
Page 2: Table Of Contents
TAbLE Of CONTENTS 100683 - CURvED ShAfT TRiMMER TAbLE Of CONTENTS Specifications .......... -
Page 3: Introduction
100683 - CURvED ShAfT TRiMMER iNTRODUCTiON SAfETY DEfiNiTiONS Congratulations on your purchase of a Champion Power The purpose of safety symbols is to attract your attention to Equipment (CPE) product. CPE designs, builds, and supports possible dangers. The safety symbols, and their explanations, all of our products to strict specifications and guidelines. -
Page 4: Important Safety Instructions
SAfETY iNSTRUCTiONS 100683 - CURvED ShAfT TRiMMER iMPORTANT SAfETY iNSTRUCTiONS – Service on the trimmer must be performed by qualified repair personnel only. Service or maintenance performed – Do not allow children or untrained individuals to use this by unqualified personnel could result in injury to the user or unit. - Page 5 SAfETY iNSTRUCTiONS 100683 - CURvED ShAfT TRiMMER – Mix fuel outdoors where there are no sparks or flames. – Loosen fuel cap slowly to release pressure and to keep fuel from escaping around the cap. – Tighten the fuel cap securely after refueling.
-
Page 6: Safety Labels
Artwork Notes Revision Changes 3mm corner radius; 2mm safe margin; to be printed on white substrate. This artwork belongs to Champion Power Equipment. The contents are confidential and privileged and shall not be disclosed to or used by or for... -
Page 7: Safety Symbols
SAfETY iNSTRUCTiONS 100683 - CURvED ShAfT TRiMMER Safety Symbols Some of the following symbols may be used on this product. Please study them and learn their meaning. Proper interpretation of these symbols will allow you to more safely operate the product. -
Page 8: Operation Symbols
4. Holding the unit firmly, pull starter handle until the engine on white substrate. starts. This artwork belongs to Champion Power Equipment. The contents are confidential and privileged and shall not be disclosed to or used by or for outside parties without the explicit consent of Champion Power Equipment. -
Page 9: Controls And Features
CONTROLS AND fEATURES 100683 - CURvED ShAfT TRiMMER CONTROLS AND fEATURES Read this operator’s manual before operating your grass trimmer. Familiarize yourself with the location and function of the controls and features. Save this manual for future reference. Trimmer 1. Bump Feed Trimmer Head 7. -
Page 10: Parts Included
CONTROLS AND fEATURES 100683 - CURvED ShAfT TRiMMER Parts included Handle................... 1 Bolts ..................2 Accessories Allen wrench (4 mm) ............. 1 Spark plug wrench ..............1 2-cycle oil .............2.6 fl .oz.(76 ml) Assembly Parts Trimmer Head ................ 1 Grass Shield ................1... -
Page 11: Assembly
ASSEMbLY 100683 - CURvED ShAfT TRiMMER ASSEMbLY Your trimmer requires some assembly. If you have any questions regarding the assembly of your trimmer, call our Technical Support Team at 1-877-338-0999. Please have your serial number and model number available. 1. Attach the trimmer handle by placing both pieces of the handle around the trimmer shaft at the desired length. -
Page 12: Filling The Fuel Tank
OPERATiON 100683 - CURvED ShAfT TRiMMER filling the fuel Tank NOTiCE 1. Place the trimmer on a flat stable surface, with the fuel Gasoline containing up to 10% ethanol by volume (commonly tank cap facing upwards. referred to as E10) is acceptable. E15 and E85 are not. -
Page 13: To Stop The Engine
OPERATiON 100683 - CURvED ShAfT TRiMMER To Start a Warm Engine: 4. Holding the unit firmly, pull starter handle until the engine starts. 1. Do not adjust the CHOKE lever. It should already be in the RUN position. If not, press the throttle trigger lockout (top) and throttle trigger (bottom) once. -
Page 14: To Extend Line
OPERATiON 100683 - CURvED ShAfT TRiMMER To Extend Line GENERAL TIPS: – To reduce sound levels, limit the number of pieces of This unit features a bump feed trimmer head. If the cutting equipment used at any one time. swath has decreased do to wear or breaking, firmly bump the bump feed on the trimmer head on the ground to extend the –... -
Page 15: Replacing Trimmer Line
MAiNTENANCE 100683 - CURvED ShAfT TRiMMER Replacing Trimmer Line 6. Thread the remaining string through the holes on the string trimmer head assembly. 1. Place the provided Allen wrench or a screw driver into the cut out on the trimmer head to prevent the assembly from moving. -
Page 16: Cleaning The Air Filter
SPECifiCATiONS 100683 - CURvED ShAfT TRiMMER Cleaning the Air filter BEFORE USE For proper performance and long life, keep the air filter clean. — Wipe up fuel leaks, fuel spillage. 1. Move choke knob to CHOKE position (See Cold Start —... -
Page 17: Parts Diagram Overview
SPECifiCATiONS 100683 - CURvED ShAfT TRiMMER Parts Diagram Overview Parts Diagram Overview List Part Number Description Qty. WG375Q23.1 Figure A GT26.8 Figure B CG260E-5B Figure C CG260.3 Figure D WG375Q23.2 Figure E 3CS260.1 Figure F WG375Q23.3 Figure G 80114938 Figure H... -
Page 18: Parts Diagram (A)
SPECifiCATiONS 100683 - CURvED ShAfT TRiMMER Parts Diagram (A) Figure A Parts List (A) Part Number Description Qty. 2320120947 Roper Holder 2320089493 Spring 2320120948 Rope Support Nylon Rope Ø2.5 × 2320111584 3000 2320002966 Case 2320002546 Nut M8... -
Page 19: Parts Diagram (B)
SPECifiCATiONS 100683 - CURvED ShAfT TRiMMER Parts Diagram (b) Figure B Parts List (b) Part Number Description Qty. Part Number Description Qty. 2320089414 Washer 2320121828 Oil Pipe 2320109011 Screw Shaft 2310004247 Bearing 628-2RS/P6 2310000192 10303615 Link Body 2310003806 Bearing 608-2RS/P6... -
Page 20: Parts Diagram (C)
SPECifiCATiONS 100683 - CURvED ShAfT TRiMMER Parts Diagram (C) Figure C Parts List (C) Part Number Description Qty. Nut, M5, HZ 2310000142 2320007748 Knife 2310000478 Screw M5 × 16, HZ 2320096421 Protector... -
Page 21: Parts Diagram (D)
SPECifiCATiONS 100683 - CURvED ShAfT TRiMMER Parts Diagram (D) Figure D Parts List (D) Part Number Description Qty. 2320070118 Loacting Ring 2320121894 Screw M5 × 18, CE 2310000142 Nut M5... -
Page 22: Parts Diagram (E)
SPECifiCATiONS 100683 - CURvED ShAfT TRiMMER Parts Diagram (E) Figure E Parts List (E) Part Number Description Qty. Front axis assembly 2320100643 2320100645 Bracing 2320100642 Pipe... -
Page 23: Parts Diagram (F)
SPECifiCATiONS 100683 - CURvED ShAfT TRiMMER Parts Diagram (f) Figure F Parts List (f) Part Number Description Qty. Handle 2320077337 2320077338 Handle Cover 2320031146 Screw M5 × 25, CE... -
Page 24: Parts Diagram (G)
SPECifiCATiONS 100683 - CURvED ShAfT TRiMMER Parts Diagram (G) Figure G Parts List (G) Part Number Description Qty. Part Number Description Qty. 2320038381 Clamp 2310000142 Nut, M5 2320022241 Box, Left 2310001588 Screw M5 × 16, CZH 2320001181 Tine 2320120402 Stop Switch... -
Page 25: Parts Diagram (H)
SPECifiCATiONS 100683 - CURvED ShAfT TRiMMER Parts Diagram (h) Figure H Parts List (h) Part Number Description Qty. Engine 80114938... -
Page 26: Engine Parts Diagram
SPECifiCATiONS 100683 - CURvED ShAfT TRiMMER Engine Parts Diagram... -
Page 27: Engine Parts List
SPECifiCATiONS 100683 - CURvED ShAfT TRiMMER Engine Parts List Part Number Description Qty. Part Number Description Qty. Screw Assembly, M5 × 2320068749 Gasket Insulator 2310004829 16 , Black 2320104306 Insulator 2320072616 Starter 2320008614 Gasket, Carburetor 2320072617 Guide Cover Assembly 2320120630... -
Page 28: Troubleshooting
TROUbLEShOOTiNG 100683 - CURvED ShAfT TRiMMER TROUbLEShOOTiNG Problem Cause Solution Fuel mixture is too rich. Open choke. Fuel strainer clogged. Clean fuel strainer. Fuel line clogged. Clean fuel line. Engine does not start. Let unit sit for 15 minutes or remove spark Flooded engine. - Page 29 To register your product for warranty and FREE lifetime call center beyond the manufacturer’s control. technical support please visit: – Problems caused by parts that are not original Champion https://www.championpowerequipment.com/register Power Equipment parts. To complete registration you will need to include a copy of the When applicable, this warranty does not apply to products used purchase receipt as proof of original purchase.
- Page 30 THE UNITED STATES ENVIRONMENTAL PROTECTION AGENCY (U.S. EPA) EMISSION CONTROL SYSTEM WARRANTY Your Champion Power Equipment (CPE) engine complies with U.S. EPA emissions regulations. YOUR WARRANTY RIGHTS AND OBLIGATIONS: The U.S. EPA and CPE are pleased to explain the Federal Emission Control System’s Warranty on your 2020 small off-road engine and engine powered equipment.
- Page 31 EMISSION CONTROL SYSTEM WARRANTY 1. APPLICABILITY: This section applies to Emissions Control Systems on small off-road engines or equipment that use small off-road engines subject to the emission standards in this Article. The warranty period begins on the date the new engine or equipment is delivered to an ultimate purchaser and shall continue for 24 consecutive months thereafter.
- Page 32 You must take your CPE engine or the product on which it is installed, along with your warranty registration card or other proof of original purchase date, at your expense, to any Champion Power Equipment dealer who is authorized by Champion Power Equipment, Inc. to sell and service that CPE product during normal business hours.