Tunturi J7 Owner's Manual page 8

In order to improve the reliability of recovery
pulse measurement, always try to standardize the
measurement situation as accurately as possible;
start measuring at the same heart rate level as
precisely as possible. The measurement takes two
minutes, during which the text
heart rate are displayed. Try not to move during
the measurement. At the end of the period the
text and the recovery ratio percentage are
rESU
displayed. The smaller the reading the fitter you
are. Note that results are dependent on the starting
pulse level, they are individual and not directly
comparable with those of others.
M A I N T E N A N C E
Do not attempt any servicing or
C AU T I O N !
adjustment other than those described in this
manual. Any other servicing must be performed
by an authorized service representative. Check the
tightness of all fixing screws once a year. Do not
overtighten.
L U B R I CAT I N G T H E R U N NI N G D E CK
Lubrication is the most important service activity
for the treadmill. This is absolutely essential, if the
friction of the running deck increases noticeably
or the motor begins to heat up; increased friction
is indicated by jerky movement of the belt or by
error code 15 appearing on the display. Insufficient
lubrication will cause the belt, running deck and
motor to wear out and break. The need for
re-lubrication depends to a great extent on the
running styles and weight of the user: heavy user
weight and slow speed put particular strain on the
device and therefore demand greater lubrication.
We recommend you check the lubrication after
every 100 hours of use. If the inside of the belt
is not moist with T-Lube, lubricate the belt with
T-Lube immediately. Use only T-Lube lubricant to
lubricate the treadmill. Contact your local Tunturi
distributor for further supplies of T-Lube.
8
Attach the nozzle to the T-Lube container. Let
the treadmill run at 1,5 km/h. Push the nozzle
completely into either lubrication pipe. Spray
T-Lube into the pipe until the belt has rotated once
(see the seam of the belt), stop spraying and pull
and the
rECO the nozzle out. The treadmill is instantly ready for
use.
C LEA N IN G T HE T R EA DMI L L
Wipe the treadmill surfaces, especially the
handlebars and meter from dust with a damp
cloth or towel. Do not use solvents. Use a small
vacuum nozzle to carefully vacuum around all
visible components (belt, running deck, side rails
etc.). To clean the underside of the treadmill,
carefully turn the treadmill on its side, or if your
treadmill is J7F, lift the running deck to the storage
position.
A LI G NI NG THE R U NN IN G B ELT
Monitor belt tracking during exercise and make
adjustments as needed. The belt should run in the
centre of the treadmill. Alignment is not usually
needed, provided
•
and horizontal surface and the belt is correctly
tensioned
•
pushed to one side due to the user's running style
(e.g. more weight on one foot). The alignment of
the belt is adjusted by turning the two bolts at the
back of the treadmill. Align the belt according to
the following instructions:
1.
treadmill's speed to 5 km/h (3 mph).
2 .
adjustment bolt 1/8 turn clockwise and the right
adjustment bolt 1/8 turn anticlockwise. Do not
turn more than 1/8 at the time as already very
small adjustments effect the alignment.
•
adjustment bolt 1/8 turn clockwise and the left
adjustment bolt 1/8 turn anticlockwise.
3 .
correct. If not, continue to make small adjustments
as above until the belt is correctly aligned.
the treadmill is placed on an even, solid
the alignment of the belt is correct
It is, however, possible for the belt to be
Turn the power switch on and increase the
If the belt drifts to the left, turn the left
If the belt drifts to the right, turn the right
If the belt remains centered the adjustment is