Page 2
Thank you for your purchase of Magnetek’s Telemotive brand MLTX Radio Remote Crane Control. Magnetek has set a whole new standard in radio-remote performance, dependability, and value with this unique new line of belly box transmitters. Without a doubt, our Telemotive MLTX is the ultimate solution for having precise, undeterred, and safe control of your material.
2.21: ANALOG VOLTAGE REFERENCE ....................14 2.22: BATTERIES ............................14 2.23: REPROGRAMMING THE PART 15 TRANSMITTER SYNTHESIZER ........15 2.24: CHANNEL AND FREQUENCY DESIGNATIONS BY COUNT ............ 16 2.25: ASSEMBLY AND REPLACEMENT PARTS ................... 17 Telemotive MLTX Transmitter Instruction Manual 1/13/2012 Page 3 of 19...
Page 4
The following information is intended to be used in conjunction with other rules or regulations already in existence. It is important to read all of the safety information contained in this section before installing or operating the Radio Control System. Telemotive MLTX Transmitter Instruction Manual 1/13/2012 Page 4 of 19...
EQUIPMENT, ETC. MECHANICALLY LOCKING INTERMEDIATE RELAY SYSTEM WITH SEPARATE POWER CONSIDERATIONS MUST BE PROVIDED. FAILURE TO FOLLOW THIS WARNING COULD RESULT IN SERIOUS INJURY OR DEATH AND DAMAGE TO EQUIPMENT. Telemotive MLTX Transmitter Instruction Manual 1/13/2012 Page 5 of 19...
Test the hoist brake to verify there is no drift without a load. If any crane or hoist fails any of the above tests notify the supervisor then lockout and tagout for repair. Telemotive MLTX Transmitter Instruction Manual 1/13/2012 Page 6 of 19...
Do not charge batteries in a hazardous environment. Do not short charger. Do not attempt to charge a damaged battery. Do not attempt to use a battery that is leaking, swollen or corroded. Telemotive MLTX Transmitter Instruction Manual 1/13/2012 Page 7 of 19...
1.12: BATTERY DISPOSAL Before disposing of batteries consult local and governmental regulatory requirements for proper disposal procedure. Use only Telemotive approved chargers for the appropriate battery pack. Telemotive MLTX Transmitter Instruction Manual 1/13/2012 Page 8 of 19...
HOIST BRIDGE HOIST BRIDGE AUX TROLLEY MAIN TROLLEY HOIST AUX HOIST “MLTX-5L-5M-3S” has 5 Levers and 3 Speeds “MLTX-4L-3M-3S” has 4 Levers and 3 Speeds Pre-engineered Figure 1. MLTX Control Telemotive MLTX Transmitter Instruction Manual 1/13/2012 Page 9 of 19...
These switches activate special function relays that control items such as alarms or lights depending on how the receiver is wired. The switches are momentary and activate the function as long as the switch is depressed. Telemotive MLTX Transmitter Instruction Manual 1/13/2012 Page 10 of 19...
Two hoists, one trolley and one bridge with main hoist (A), auxiliary hoist (B), and “both” (BOTH) main and auxiliary hoists are selectable by the rotary switch. Telemotive MLTX Transmitter Instruction Manual 1/13/2012 Page 11 of 19...
The programming tables with the transmitter extended crane control configurations are found in the appropriate receiver manual. In these sections, if the MLTX is not specifically listed, use the switch programming guide for the configurations labeled SLTX or JLTX (they are the same). Telemotive MLTX Transmitter Instruction Manual 1/13/2012 Page 12 of 19...
2.16: PRE-ENGINEERED MLTX TRANSMITTER BOARD SETUP INFORMATION The Pre-engineered MLTX CPU Board is shown in Figure 2. Refer to paragraphs 2-17 through 2-18 for setups. Figure 2. Pre-engineered MLTX CPU Board. Telemotive MLTX Transmitter Instruction Manual 1/13/2012 Page 13 of 19...
Ensure that JU3 and JU4 are both set properly for your transmitter’s battery. For 9V disposable alkaline and 7.2V rechargeable NiMH, JU3 and JU4 must be set for 7.2V. For 12V rechargeable NiMH, JU3 and JU4 must be set for 12V. Telemotive MLTX Transmitter Instruction Manual 1/13/2012 Page 14 of 19...
Section 2.6 of RSS-102 This portable transmitter with its antenna complies with Industry Canada RF Exposure Limits for General Population / Uncontrolled Exposure. Telemotive MLTX Transmitter Instruction Manual 1/13/2012 Page 15 of 19...
2.25: ASSEMBLY AND REPLACEMENT PARTS If your transmitter ever needs repair, we always recommend that you have Magnetek service perform the repair. If you need to refer to a parts list, refer to your transmitters drawing that was included in the shipment of your transmitter.
Need help?
Do you have a question about the Telemotive MLTX and is the answer not in the manual?
Questions and answers