Related Manuals for King Canada KC-3310TS
Summary of Contents for King Canada KC-3310TS
- Page 1 10” SLIDING TILE SAW WITH LASER GUIDE • Enhanced laser effect MODEL: KC-3310TS INSTRUCTION MANUAL COPYRIGHT © 2020 ALL RIGHTS RESERVED BY KING CANADA TOOLS INC.
-
Page 2: Warranty Information
Please keep your dated proof of purchase for warranty and servicing purposes. REPLACEMENT PARTS Replacement parts for this product are available at our authorized King Canada service centers across Canada. Please use the 10 digit part numbers listed in this manual for all part orders where applicable. -
Page 3: General Safety Instructions
GENERAL SAFETY INSTRUCTIONS VOLTAGE WARNING: Before connecting the tool to a power source (receptacle, outlet, etc.) be sure the voltage supplied is the same as that specified on the nameplate of the tool. A power source with voltage greater than that for the specified tool can result in SERIOUS INJURY to the user - as well as damage to the tool. - Page 4 14. Keep your work space clear and free of all debris. 15. Keep the tile saw clean and maintained to achieve the safest and highest performance for each job. KEEP THESE SAFETY RULES FOR FUTURE REFERENCE TILE SAW SPECIFICATIONS Model ....................................KC-3310TS Voltage ......................................120V Horsepower ....................................2.5 HP Amperage ....................................15 Amp.
-
Page 5: Electrical Information
ELECTRICAL INFORMATION WARNING! ALL ELECTRICAL CONNECTIONS MUST BE DONE BY A QUALIFIED ELECTRICIAN. FAILURE TO COMPLY MAY RESULT IN SERIOUS INJURY! ALL ADJUSTMENTS OR REPAIRS MUST BE DONE WITH THE TILE SAW DISCONNECTED FROM THE POWER SOURCE. FAILURE TO COMPLY MAY RESULT IN SERIOUS INJURY! POWER SUPPLY WARNING: YOUR TILE SAW MUST BE CONNECTED TO A 120V, 15-AMP. -
Page 6: Unpacking, Assembly & Set Up
ASSEMBLY UNPACKING, ASSEMBLY & SET UP Caution: Follow all of the assembly & installation instructions completely before connecting the Tile Saw to a power source or turning the motor on. Carefully open the main box and remove all the saw components and packing materials. - Page 7 ASSEMBLY ASSEMBLING HEAD TO MACHINE FRAME The following steps should be done with the help of a second person. 1) Position the head (A) Fig.7 up against the frame (B) and secure head to frame using 5 large cap screws and washers (C) Fig.7 and (A) Fig.8. 2) Secure the head to the frame by tightening the 5 cap screws using the supplied 8 mm hex.
- Page 8 ASSEMBLY INSTALLING THE WATER TRAY AND RECIRCULATING WATER PUMP 1) Locate the plastic water tray (A) Fig.11 and slide it under the table inside the machine frame as shown. Make sure the drain plug (B) is installed tightly. 2) Locate the water pump (C) Fig.11. The water pump comes with suction cups underneath it, wet the suction cups.
- Page 9 ASSEMBLY INSTALLING/REMOVING 10” WET TYPE DIAMOND BLADE continued... Warning: For maximum performance and safety, only use 10” Wet Type Tile Saw blades with this Tile Saw. Do not use 10” Wet Type Tile Saw blades that are rated below the no load speed rating of this Tile Saw (4500 RPM). Do not use a damaged blade.
-
Page 10: Assembly And Adjustments
ASSEMBLY & ADJUSTMENTS INSTALLING WATER TRAY EXTENSIONS continued... 2) Next, install the front side tray extension (A) Fig.19. Align the engraved marks (B) with the rail hooks (C), slightly tilt the tray and hook it onto the two rail hooks and under the supports (D). -
Page 11: Operational Guidelines
OPERATION FILLING THE WATER TRAY WITH WATER 1) Before attempting to fill water tray with water, it is important that the water pump (A) Fig.23 be secured to the water tray and that the drain plug (B) is position in the drain hole. 2) Fill the water tray with water up to the MAX fill line (C) Fig.23 before operating this Tile Saw. -
Page 12: Operation And Maintenance
• Reassemble using new carbon brush assemblies (not included). Reinstall brush caps (A). Tighten brush caps securely. Do not overtighten. PARTS DIAGRAM & PARTS LISTS Refer to the Parts section of the King Canada web site for the most updated parts diagram and parts list.
Need help?
Do you have a question about the KC-3310TS and is the answer not in the manual?
Questions and answers