Advertisement
2753 Michigan Road • Madison, Indiana 47250 • 812-574-7777
Bracket, L
Extension
8x
M8-1.25 x 16mm Lg. FHCS
8x
M8-1.25 Nylock Nut
Read instructions and view illustrations before beginning.
Need help with your installation?
sales@superatv.com
1-812-574-7777
Thank You
®
© 2015 SuperATV.com
. All Rights Reserved.
Tube, L
(Ranger
8x
www.superatv.com
8:00am - 9:00pm EST M-Th
8:00am - 7:00pm EST Friday
9:00am - 2:00pm EST Saturday
For Choosing
INSTALLATION INSTRUCTIONS
Wakeboard Speaker Mount:
for Polaris Ranger
Bracket, R
XP 900 will not require Brackets)
®
M8 Flat Washer
Liability Statement
SuperATV's
products are designed to best fit user's ATV/UTV under stock
®
conditions. Adding, modifying, or fabricating any factory or aftermarket parts will
void any warranty provided by SuperATV
products could interfere with other aftermarket accessories. If user has aftermarket
products on machine, contact SuperATV
Although SuperATV
that installing lift kits, long travel, or suspension kits, tires, etc. will change the ride
of machine and may increase maintenance and part wear. Operating any off-road
machine while, or after, consuming alcohol and/or drugs increases risk of bodily
harm or death. No warranty or representation is made as to this product's ability to
protect user from severe injury or death. SuperATV
to wear a helmet and appropriate riding gear at all times.
By purchasing and installing SuperATV
occur, SuperATV
replacement parts, or freight charges. SuperATV
responsible for any direct, indirect, incidental, special, or consequential damages
that result from any product purchased from SuperATV
user for all damages, losses, and causes of action, if any, shall not exceed the total
purchase price paid for the product that gave rise to the claim.
SuperATV
will warranty only parts provided by SuperATV
®
problems with OEM housings, bearings, seals, or other manufacturers' products will
not be covered by SuperATV
item was not installed properly, misused, or modified.
(Full and Mid size)
®
Wedge Clamp Assembly:
- Set Screw
- Clamp Top
- Clamp Bottom
Tube, R
and is not recommended. SuperATV's
®
to verify that they will work together.
®
has thousands of satisfied customers, user should be aware
®
urges operators and occupants
®
products, user agrees that should damages
®
will not be held responsible for loss of time, use, labor fees,
®
, nor any 3rd party, will not be held
®
®
. SuperATV
parts and products are not warrantied if
®
®
®
. The total liability of seller to
. Any damage or
®
IN-WBM-P-RAN 12/3/2015
Advertisement
Table of Contents
Related Manuals for SuperATV WBM-P-RAN
Summary of Contents for SuperATV WBM-P-RAN
- Page 1 No warranty or representation is made as to this product’s ability to 8:00am - 9:00pm EST M-Th protect user from severe injury or death. SuperATV urges operators and occupants ®...
- Page 2 - Install Bracket, L to Cab Frame with hardware shown. - Repeat for opposite side. Cab Frame (Driver Side) Bracket, L (Driver Side) (Ranger XP 900 will not require Brackets) ® Bracket, L M8 x 16mm front M8 Flat Washer (2) each M8 Nylock Nut IN-WBM-P-RAN...
- Page 3 M8 x 16mm (Driver Side) - Install Tube, L to Bracket, L with hardware shown. Bracket, L Tube, L front (Driver Side) (2) each M8 Nylock Nut M8 Flat Washer M8 x 16mm See following page for model specific configurations IN-WBM-P-RAN...
- Page 4 - Tighten provided Set Screw. Wedge Clamp halves - Install Tube, R to Bracket, R with provided M8 hardware. - Align assembly to machine and tighten all hardware completely. Installed on Ranger XP 900 ® ( SuperATV p/n MTX-TS speakers not included) IN-WBM-P-RAN...
Need help?
Do you have a question about the WBM-P-RAN and is the answer not in the manual?
Questions and answers