Subscribe to Our Youtube Channel
Related Manuals for ASROCK Rack X570D4I-2T
Summary of Contents for ASROCK Rack X570D4I-2T
- Page 1 X570D4I-2T User Manual Version 1.0 Published May 2020 Copyright©2020 ASRock Rack INC. All rights reserved.
-
Page 2: Copyright Notice
In no event shall ASRock Rack, its directors, officers, employees, or agents be liable for any indirect, special, incidental, or consequential damages (including damages for loss of profits, loss of business, loss of data, interruption of business and the like), even if ASRock Rack has been advised of the possibility of such damages arising from any defect or error in the documentation or product. -
Page 3: Contact Information
Contact Information If you need to contact ASRock Rack or want to know more about ASRock Rack, you’re welcome to visit ASRock Rack’s website at www.ASRockRack.com; or you may contact your dealer for further information. ASRock Rack Incorporation 6F., No.37, Sec. 2, Jhongyang S. Rd., Beitou District,... -
Page 5: Chapter 1 Introduction
In case any modifications of this manual occur, the updated version will be available on ASRock Rack website without further notice. You may find the latest memory and CPU support lists on ASRock Rack website as well. ASRock Rack’s Website: www.ASRockRack.com If you require technical support related to this motherboard, please visit our website for specific information about the model you are using. -
Page 6: Specifications
6.7'' x 6.7'' (17.02cm x17.02 cm) Processor System AMD Ryzen™ 3 Generation Series Processors* *We recommend using the CPU HS listed in the Cooler QVL section on our ASRock Rack website. *Only LGA115x CPU heatsink is supported. Chipset AMD X570 System Memory... - Page 7 256Mb AMI UEFI Legal BIOS BIOS Features - Plug and Play (PnP) - ACPI 2.0 Compliance Wake Up Events - SMBIOS 2.8.0 Support - ASRock Rack Instant Flash Hardware Monitor Temperature - CPU/PCH/DDR/LAN/Storage Temperature Sensing - MB/Card side/TR1 Temperature Sensing...
- Page 8 Support OS Environment Temperature Operation temperature: 10°C ~ 35°C / Non operation temperature: -40°C ~ 70°C NOTE: Please refer to our website for the latest specifications. This motherboard supports Wake from on Board LAN. To use this function, please make sure that the “Wake on Magic Packet from power off state”...
-
Page 9: Unique Features
POST or the <F2> key to enter into the BIOS setup menu to access ASRock Rack Instant Flash. Just launch this tool and save the new BIOS file to your USB flash drive, floppy disk or hard drive, then you can update your BIOS only in a few clicks without preparing an additional floppy diskette or other complicated flash utility. -
Page 10: Motherboard Layout
USB 3.1 Gen2 IPMI_LAN T: USB_1 B: USB_2 TPM1 LAN2 LAN1 FAN1 (NCSI) M2_1 X570 BIOS UID1 USB3_3_4 COM1 OCU1 OCU2 IPMB_1 SATAPWR1 FAN2 BMC_SMB_1 FAN3 PWM_CFG1 ITX_AUX_PANEL1 CLRMOS1 PANEL1 PLED PWRBTN PCIE7 SPEAKER1 CHASSIS_ID1 HDLED RESET X570D4I-2T 17 16... - Page 11 X570D4I-2T Description 2 x 260-pin DDR4 SO-DIMM Slots (DDR4_A2, DDR4_B2) 2 x 260-pin DDR4 SO-DIMM Slots (DDR4_A1, DDR4_B1) ATX 4-PIN Power Connector (ATX4PIN1)* ATX 12V Power Connector (ATX12V2) PSU SMBus (PSU_SMB1) Thermal Sensor Header (TR1) TPM Header (TPM1) System Fan Connector (FAN1) OCuLink x4 Connector (OCU1) USB 3.1 Gen1 Header (USB3_3_4)
-
Page 12: Onboard Led Indicators
1.5 Onboard LED Indicators DDR4_B1 (64 bit, 260-pin module) DDR4_B2 (64 bit, 260-pin module) DDR4_A1 (64 bit, 260-pin module) DDR4_A2 (64 bit, 260-pin module) X570 PLED PWRBTN HDLED RESET X570D4I-2T Item Status Description SB_PWR1_LED Green STB PWR ready LED_FAN1 Amber... - Page 13 X570D4I-2T 1.6 I/O Panel No. Description No. Description USB 3.1 Gen2 Ports (USB3_1_2) 10G LAN RJ-45 Port (LAN2)** LAN RJ-45 Port (IPMI_LAN)* VGA Port (VGA1) 10G LAN RJ-45 Port (LAN1)** UID Switch (UID1) LAN Port LED Indications *There are two LEDs on each LAN port. Please refer to the table below for the LAN port LED indications.
- Page 14 **There are two LEDs on each LAN port. Please refer to the table below for the LAN port LED indications. ACT/LIN K LED SPEED LED ACT/LIN K LED SPEED LED LAN Port 10G LAN Port (LAN1, LAN2) LED Indications Activity / Link LED Speed LED Status Description...
-
Page 15: Block Diagram
X570D4I-2T 1.7 Block Diagram... -
Page 16: Chapter 2 Installation
Chapter 2 Installation This is a mini ITX form factor (6.7'' x 6.7'', 17.02 cm x 17.02 cm) motherboard. Before you install the motherboard, study the configuration of your chassis to ensure that the motherboard fits into it. Make sure to unplug the power cord before installing or removing the motherboard. Failure to do so may cause physical injuries to you and damages to motherboard components. -
Page 17: Installing The Cpu
X570D4I-2T 2.3 Installing the CPU Unplug all power cables before installing the CPU. -
Page 18: Installing The Cpu Fan And Heatsink
2.4 Installing the CPU Fan and Heatsink Please be aware that this motherboard only supports LGA115x CPU heatsink... -
Page 19: Installation Of Memory Modules (Dimm)
X570D4I-2T 2.5 Installation of Memory Modules (DIMM) This motherboard provides four 260-pin DDR4 (Double Data Rate 4) DIMM slots. A single memory module should be installed in the A1 or B1 socket. Two memory modules should be installed in the A1+B1, A1+A2, or B1+B2 sockets. -
Page 21: Expansion Slot (Pci Express Slot)
X570D4I-2T 2.6 Expansion Slot (PCI Express Slot) There is a PCI Express slot on this motherboard. PCIE slot: PCIE7 (PCIe 3.0/4.0 x16 slot) is used for PCI Express x16 lane width cards. Slot Generation Mechanical Electrical Source x8 or x16 PCIE 7 3.0/4.0... -
Page 22: Jumper Setup
2.7 Jumper Setup The illustration shows how jumpers are setup. When the jumper cap is placed on the pins, the jumper is “Short”. If no jumper cap is placed on the pins, the jumper is “Open”. The illustration shows a 3-pin jumper whose pin1 and pin2 are “Short” when a jumper cap is placed on these 2 pins. -
Page 23: Onboard Headers And Connectors
X570D4I-2T 2.8 Onboard Headers and Connectors Onboard headers and connectors are NOT jumpers. Do NOT place jumper caps over these headers and connectors. Placing jumper caps over the headers and connectors will cause permanent damage to the motherboard. System Panel Header... - Page 24 ATX 12V Power The motherboard provides one Connector 8-pin 12V power connector (8-pin ATX12V2) which is a required input for (see p.6, No. 4) either DC-IN 12V or ATX +12V power source. When using ATX power, it is necessary to use a 24pin-to- 4pin power cable to connect between the 24pin power connector of PSU and the...
- Page 25 X570D4I-2T SATA Power Connector Please use a SATA power cable (4-pin SATAPWR1) to connect this SATA Power (see p.6, No. 14) Connector and your SATA +12V HDD for supplying power from the motherboard, when using DC-IN mode without SATA power supply.
- Page 26 Thermal Sensor Header Please connect the thermal (3-pin TR1) sensor cable to either pin 1-2 (see p.6, No. 6) or pin 2-3 and the other end to the device which you wish to monitor its temperature. PWM Configuration This header is used for PWM Header configurations.
- Page 27 X570D4I-2T Intelligent Platform This 4-pin connector is used IPMB_SDA Management Bus Header to provide a cabled base-board IPMB_SCL (4-pin IPMB_1) or front panel connection for (see p.6, No. 22) value added features and 3rd- party add-in cards, such as No Connect...
-
Page 28: Unit Identification Purpose Led/Switch
2.9 Unit Identification purpose LED/Switch With the UID button, You are able to locate the server you’re working on from behind a rack of servers. Unit Identification When the UID button on the purpose LED/Switch front or rear panel is pressed, (UID1) the front/rear UID blue LED indicator will be turned on. - Page 29 X570D4I-2T 2.11 Dual LAN and Teaming Operation Guide Dual LAN with Teaming enabled on this motherboard allows two single connections to act as one single connection for twice the transmission bandwidth, making data transmission more effective and improving the quality of transmission of distant images.
- Page 30 2.12 M.2_SSD (NGFF) Module Installation Guide (M2_1) The M.2, also known as the Next Generation Form Factor (NGFF), is a small size and versatile card edge connector that aims to replace mPCIe and mSATA. This M.2_SSD (NGFF) Socket 3 can accommodate a SATA3 6.0 Gb/s module or a PCI Express module up to Gen4 x4 (64 Gb/s) only.
Need help?
Do you have a question about the X570D4I-2T and is the answer not in the manual?
Questions and answers