Related Manuals for ACV BNE Series
Summary of Contents for ACV BNE Series
- Page 1 Installation, operating and maintenance Instructions BNE 1 - BNE 2 - BNE 3 EN • 1 664Y1200.B...
- Page 2 INDEX INTRODUCTION Who should read these instructions Symbols Applicable standards Important notes USER GUIDE Use of the boiler Burner shutdown DESCRIPTION General description Operating principle Design characteristics Boiler views and key to parts TECHNICAL CHARACTERISTICS General Operating condition limits Dimensions Domestic hot water performance General characteristics INSTALLATION...
-
Page 3: Who Should Read These Instructions
The product must be installed and serviced by qualified engineers in accordance with the regulations in force. ACV declines all liability for any damage caused as a result of installation or in the event of the use of appliances or accessories Danger of electrocution. -
Page 4: Use Of The Boiler
USER GUIDE USE OF THE BOILER To ensure that your system operates correctly, please 7. Thermostat-pressure gauge have it serviced annually by a qualified engineer; This gauge shows the temperature of the boiler and the pressure in servicing should be completed before the start of the the primary heating circuit. -
Page 5: General Description
USER GUIDE DESCRIPTION The water escaping from the safety valve can GENERAL DESCRIPTION be extremely hot and cause serious burns. • Combined boiler and water heater (heating and domestic hot water) • Hot water generated by an indirect storage system. •... -
Page 6: Heating Element
DESCRIPTION Casing BOILER VIEWS AND KEY TO PARTS The boiler is covered with a steel casing that has been stove enamelled at 220°C after scouring and phosphating. 1. Cold water inlet 2. Hot water thermostat pocket 3. Hot water outlet Storage exchanger 4. - Page 7 TECHNICAL CHARACTERISTICS GENERAL OPERATING CONDITION LIMITS The appliances are supplied fully assembled, tested and packed Maximum service pressure (tank filled with water) standing on a timber transport base with impact protection strips - Heating circuit: 3 bar and wrapped in heat-shrunk plastic film. When the appliance arrives, - Hot water circuit: 10 bar remove the packaging and check that no parts have been damaged in transit.
-
Page 8: Installation
INSTALLATION BOILER ROOM A. High-level ventilation B. Low-level ventilation C. Draught stabiliser Important D. Flame inspection window • Never obstruct the ventilation. E. Height of lined chimney • Do not store inflammable products in the boiler room. F. Chimney diameter •... -
Page 9: Heating Connection
This kit comprises: Safety group • A pump; The safety group of the water tank must be approved by ACV and • A 3-way manual valve. This calibrated to 7 bar; the group’s valve discharge must be connected valve can be power-operated to the drain. -
Page 10: Electrical Connections
INSTALLATION ELECTRICAL CONNECTIONS Wiring diagram key 1. Main switch Power supply principle 2. Hot water control thermostat The boiler operates on a single-phase supply of 230 V/50 Hz. 3. Time clock You should install a control box with main switch and 6A fuses 4. -
Page 11: Burner Characteristics
BURNER CHARACTERISTICS DESCRIPTION OF THE BURNER Advantages • Simple to install, it is fitted with a safety switch and a new burner suspension system. This new generation of fuel oil burners comply with current • A special key is provided with the burner for any maintenance requirements in terms of performance and the cleanliness of work needed. -
Page 12: Burner Dimension
BURNER CHARACTERISTICS REGULATION PARAMENTER BNE 1 BNE 2 BNE 3 Type of burner BM R 31 BM R 31 BM R 51 Power 23.0 30.0 49.0 Electrical power Nozzle gal/h 0.50 0.75 1.25 Nozzle angle 60° 60° 60° Fuel oil rate of flow Kg/h 1.94 2.53... -
Page 13: Commissioning And Maintenance
COMMISSIONING AND MAINTENANCE FILLING THE DOMESTIC HOT WATER AND HEATING CIRCUITS IMPORTANT It is essential to fill the domestic hot water circuit before the heating circuit. 1. Open valves 7 and 8 to fill the domestic hot water circuit and pressurise it. -
Page 14: Draining The Boiler
COMMISSIONING AND MAINTENANCE MAINTENANCE OF SAFETY EQUIPMENT - Check that all thermostats and safety devicesoperate correctly: the boiler thermostat and the manual reset high-limit thermostat (103°C). - Check the heating circuit safety valves. DRAINING THE BOILER The water draining from the drain cock is very hot and can cause serious burns. - Page 15 N° BNE 1 BNE 2 BNE 3 21471384 21471385 21471386 21472384 21472385 21472386 21473384 21473385 21473386 21474384 21474385 21474386 21475384 21475384 21475386 21477384 21477384 21477386 30465156 30465157 30465158 2147P380 2147P381 2147P382...
- Page 16 BNE 1 BNE 2 BNE 3 24614110 24614110 24614111 54766014 54766014 54766014 ON / OFF 54766013 54766013 54766013 54442045 54442045 54442045 54764021 54764021 54764021 54441008 54441008 54441008 54766001 54766001 54766001...
- Page 17 BNE 1 BNE 2 BNE 3 54764010 54764010 54764010 54428182 54428182 54428182 49410280 49410280 49410280 50423008 50423008 50423008 55426001 55426001 55426001 47405252 47405252 47405252 63438001 63438001 63438001...
- Page 18 BNE 1 BNE 2 BNE 3 49410045 49410045 49410045 47438008 47438008 47438008 47405004 47405004 47405004 47405005 47405005 47405005 50423097 50423097 50423098 51701001 51701002 51701003 237E0009 237E0009 23860600...
Need help?
Do you have a question about the BNE Series and is the answer not in the manual?
Questions and answers