Advertisement
Quick Links
Advertisement
Related Manuals for Laser Dollhouse Designs Glenrose
Summary of Contents for Laser Dollhouse Designs Glenrose
- Page 1 The Glenrose assembly Instructions By Laser Dollhouse Designs...
- Page 2 Parts Subfloor walls marked S1-S5, Porch Stair assemblies Base marked S1-S6 S6(x3) First Floor walls and rails Front and rear roof First Floor marked 1A thru 1J 1A-1J Plexiglas inserts Second Floor marked 2A-2D Second Floor walls 2A-2D...
- Page 3 Parts continued First floor porch rails Door assemblies 3-interior / 1 Main Window Frames Chimney kits Dormer assembly kit x 3...
- Page 4 Parts continued (spiral stairs)
- Page 5 Parts continued (spiral stairs) 17 Risers double notch 1 lower Risers (larger of two) 1 Upper Riser (Smaller of two) 18 Treads 18 Handrails 1 assembly support 1 center support rail...
- Page 6 Base Floor assembly : (Note; recommend doing a dry assembly prior to gluing. This way you are familiar with the way parts go together.) Step 1. Match subfloor parts to base. S1 walls to S1 marked slots on base. continue till S1 thru S6 are fitted into the base slots should look like figure 1. figure 1 Step 2.
- Page 7 Step 3. Take the assembly support and lay on a flat surface. Next insert the dowel into the center hole. DO NOT GLUE THESE TOGETHER!!! see in figure 3 This will help keep the stairs level during assembly. Once assembly is done the assembly support will be removed and the spiral stairs inserted into the house.
- Page 8 Step 5. Using the remaining risers with two tabs (figure 7) and remaining treads glue them together with the risers on the bottom left side. Figure 8 You should have when done 17 assemblies with risers having a bottom tab and one without a tab along with the upper final.
- Page 9 Step 6. Place the center support dowel into the holder, take the step assembly with no bottom tab and insert from the top (figure 10) of the dowel and slide down to the bottom. Make sure dowel is straight up and down and step assembly is flush to the bottom.
- Page 10 Step 7. Run superglue along the outer edge where handrail will be placed (figure 12) and install handrail. Figure 13 GLUE!!! Figure 13 Figure 12...
- Page 11 Step 8. Run superglue along the right edge of your first assembled step. Figure 14 Next take one of the 17 assembled steps with a tab (figure 15) and insert on dowel and slide down and join to the lower step. Figure 16. Make sure that the front riser meets up with the lower steps handrail.
- Page 12 Step 9. Repeat steps 7 and 8 until you reach the at this point remove the stairs from the assembly support circle and install last single riser. Figures 17. Spiral stairs are now ready for inserting into house. Figure 17 Step 10.
- Page 13 Step 11. Install plexiglas into cutout of wall. Figure 19. NOTE: if gluing frames in remove protective plastic cover on plexiglas. Figure 19 Step 12. Install interior window frames. Figure 20. Figure 20...
- Page 14 Step 13. Install first floor chimney assembly to wall 1i and 2 floor chimney assembly to wall 2C. Figure 21. Figure 21 Step 14. Install first walls and rails to assembled base. Figure 22. Figure 22...
- Page 15 Step 15. Install first floor main door and interior door. Install door frames. Figure 23. Figure 23 Step 16. Install spiral stairs into circle cutout on first floor. Figure 24. Figure 24 Step 17. Install 2 floor base by aligning all 1 floor upper tabs to open slots.
- Page 16 Step 18. Install 2 floor wall marked 2A-2D. Install doors and interior door frames. Figure 26. Figure 26 Step 19. Install safety rails around stair opening as seen in figure 27. Figure 27...
- Page 17 Step 20. Install rear roof panel figure 28. Figure 28 Step 21. Install chimney to rear roof panel figure 29. Figure 29 Step 22. Install front roof panel, figure 30. Figure 30...
- Page 18 Step 23. Install dormers to front roof panel. Step 24. Install porch stairs. Assembly completed.
- Page 19 Laser Dollhouse Designs www.laserdollhouses.com Email: laserdollhouses@aol.com...