Table of Contents
Advertisement
SERVICE INFORMATION
Explanation Of Fault Codes
Adjusting Oven Temperature
Yourappliance isequipped withan electronic controlfeB-
Your new appliance has been factory tested for oven
turing built-in, self-diagnostic software. This software
temperature accuracy. Even though your oven has been
continuously monitors the control to insure safe and
tested, you may find that the cooking results with your
proper operation. If the software should detect a ques-
new oven are different from your previous oven.
tionable situation, a FAULT CODE (F plus a number) will
appear in the display and continuous beeps may sound.
If you have carefully followed the recipe, reviewed the
baking tips on page 8 and still feel cooking results do not
If A Fault Code Appears
meetyour expectations,youcan adjust the oventemper-
A fault code indicatesthatthere may be a functionaler-
ature. DO NOT ADJUST THE TEMPERATURE if only
ror.As a safetyprecaution,the control w illautomatically
one or two items are notbaking properly.
cancel the program.Followinstructions belowto deter-
mine if serviceis required.
Ifyou thinkthe ovenshouldbe hotteror cooler,you can
adjust it yourself. To decide how muchto change the
thermostat, s et the oventemperature25°F higheror tow-
During Normal Oven Cooking
er than the temperaturein your recipe,then bake. The
If a fault code appears in the display and continuous
resultsof the"test" shouldgiveyou an ideaof how much
beeps sound, press the STOP/CLEAR button.Then,
to adjustthe thermostat.
reprogramthe cookingoperation.
NOTE: On doublewall ovens,onlythe upperoven tern-
If the fault code reappearsin the display,call an autho-
peraturecan be adjustedas describedbelow.
rizedservicer.Do not usethe oven untilthe controlhas
been serviced.
To adjust the thermostat:
During A Self-Clean
Cycle
1. Press BAKE TEMP button.
Iftheovenis heavilysoiled,excessivesmokeandflaring
may resultin a fault code.If this occurs,pressthe STOP/
2. Turn SET knobuntil550° is displayed.
CLEAR buttonand allowthe oven to cool for an hour.
Then, reprogramthe ovenforthe clean cycle.
3. Press and hold the BAKE TEMP buttonfor several
secondsuntil00° appears in the display.
Ifthe faultcode reappearsin the display,call an autho-
rizedservicer. De not usethe ovenuntilthe controlhas
• If 00° does not appear in the display, press the
been serviced.
STOP/CLEAR buttonand beginagain.
• If the oven temperaturewas previouslyadjusted,
Circuit Breaker
the change will be displayed. For example, if the
temperature was reduced by 15°, -15 ° will be dis-
CANADIAN APPLIANCE ONLY
played.
Your appliance is equipped with a circuit breaker box.
The box is located either on a wall or in a cabinet next to
4. Turn the SET knob to select the temperature change
or near the appliance. If part or all of the appliance does
desired.
not operate, check to see if one of the breakers has
tripped. Reset the breaker to the ON position.
• The oven temperature can be increased up to 35°
or reduced by as much as 35° (-35 °) in 5° incre-
O
ments.
• NOTE: If you delay in selecting a temperature, the
program will automatically cancel and 00° will dis-
appear. Begin again if the program cancels.
O
5. Press the STOP/CLEAR button and the time of day
will reappear in the display. The oven will now bake at
the adjusted temperature.
•
O
,J
It is not necessary to readjust the oven temperature if
there is a power interruption. This adjustment will not
affect broil or clean temperatures.
PAGE 16
Hide quick links:
Advertisement
Table of Contents
