Table of Contents
Advertisement
SERVICE INFORMATION
Explanation Of Fault Codes
Adjusting Oven Temperature
Yourappliance is equippedwith an electronic controlfea-
Your new appliance has been factory tested for oven
turing built-in, self-diagnostic software. This software
temperature accuracy. Even though your range has
continuously monitors the control to insure safe and
been tested, you may find that the cooking results with
proper operation. If the software should detect a ques-
your new oven are different from your previous oven.
tionable situation, a FAULTCODE (F plus a number) will
appear in the display and continuous beeps may sound.
If you have carefully followed the recipe, reviewed the
bakingtips on page 12and still feel cookingresults do not
meetyour expectations,you can adjustthe oven temper-
O
ature. DO NOT ADJUST THE TEMPERATURE if only
k
I
one or two items are not baking properly.
I
I
SET
Ifyou think the oven should be hotter or cooler, you can
adjust it yourself. To decide how much to change the
thermostat, setthe oven temperature 25°F higher or low-
er than the temperature in your recipe, then bake. The
A fault code indicates that there may be a functional er-
results of the "test" should give you an idea of how much
ror. As a safety precaution, the control will automatically
to adjust the thermostat.
cancel the program.
To adjust the thermostat:
1. Press OVEN TEMP pad.
During Normal Oven Cooking
If a fault code appears in the displayand continuous
2. TurnSET knobuntil550° isdisplayed.
beeps sound, press the STOP/CLEAR pad. Then,
reprogramthe cookingoperation.
3. Press and hold the OVEN TEMP padforseveralse-
condsuntil00° appears inthe display.
If the fault code reappearsin the display,callan autho-
rizedservicer.Do net usethe ovenuntilthe controlhas
• If 00° does not appear in the display,press the
been serviced. The cooktop can be used.
STOP/CLEAR pad and begin again.
• If the oven temperature was previously adjusted,
During
A Self-Clean
Cycle
the change will be displayed. For example, if the
If the ovenisheavilysoiled,excessivesmokeandflaring
temperaturewas reducedby 15°, -15 ° willbe dis-
mayresultin a faultcode.Ifthisoccurs,pressthe STOP/
played.
CLEAR padand allowtheoventocoolfor an hour.Then,
4. Turnthe SET knobto selectthe temperaturechange
reprogram the ovenfor the clean cycle,
desired.
If the fault code reappears in the display, call an autho-
• The oven temperaturecan be increased up to 35°
rized servicer.Do not usethe oven untilthe controlhas
or reduced by as muchas 35° (-35 °) in 5° incre-
been serviced.The cooktopcan be used.
ments.
• NOTE: Ifyou delay in selectinga temperature,the
Fuses (Canadian Ranges Only)
programwill automatically canceland 00° willdis-
Yourrangeisequippedwithseven(7)type"P" fuses.The
appear.Beginagain if the programcancels.
fusesare locatedonthe backwallof the range.Remove
the storagedrawerfor accessto the fuses.
5. Pressthe STOP/CLEAR pad and the time of day will
reappear in the display.The oven will now bake at the
__
adjusted temperature.
It is not necessary to readjust the oven temperature if
there is a power interruption. This adjustment will not
affect broil or clean temperatures.
If part of your range does not operate, check to see if a
fuse has blown. A gap in the fuse strip or a darkened win-
dow indicates a blownfuse. Replace with the same type
and amperage type "P" fuse.
PAG E 20
Hide quick links:
Advertisement
Table of Contents
