Subscribe to Our Youtube Channel
Related Manuals for Federal Signal Corporation FireRay Utility Light
Summary of Contents for Federal Signal Corporation FireRay Utility Light
- Page 1 FireRay Utility Light ® Installation and Maintenance Instructions 25500385 A1 0320 Printed in U.S.A © Copyright 2016-2020 Federal Signal Corporation...
- Page 2 A copy of this limited warranty can also be obtained by written request to Federal Signal Corporation, 2645 Federal Signal Drive, University Park, IL 60484, email to info@fedsig.com or call +1 708-534-3400.
-
Page 3: Table Of Contents
Contents Safety Message to Installers and Service Personnel ..... 4 Safety Message to Operators ............5 Overview of the FireRay Utility Light ..........6 Unpacking the Product ..............6 Installing the FireRay ................ 6 Making Electrical Connections ............11 Maintaining the Light Head ............. 14 Getting Technical Support .............. -
Page 4: Safety Message To Installers And Service Personnel
Safety Message to Installers and Service Personnel Safety Message to Installers and Service Personnel People’s lives depend on your proper installation of our products. It is important to read, understand, and follow all instructions shipped with the products. Listed below are some other important safety instructions and precautions you should follow: •... -
Page 5: Safety Message To Operators
Safety Message to Operators Safety Message to Operators Peoples’ lives depend on your safe use of our products. Listed below are some important safety instructions and precautions you should follow: • Although your warning system is operating properly, it may not be completely effective. People may not see or heed your warning signal. -
Page 6: Overview Of The Fireray Utility Light
Installing the FireRay Overview of the FireRay Utility Light The Federal Signal utility light heads is a self-contained, high intensity, LED light designed for mounting to the exterior of a vehicle. All models are available in a variety of colors and have an internal flasher Model FireRay are designed for operation on 12 Vdc. -
Page 7: Figure 1 Mounting Holes
Installing the FireRay NOTE: For maximum coverage and effectiveness, mount the light assembly in a horizontal orientation (see Figure 1 ). Before proceeding with installation, determine the approximate location of the light assembly and plan all cable/wire routing. To install the FireRay: 1. -
Page 8: Figure 2 Exploded View - No Bezel
Installing the FireRay DAMAGE TO LIGHT: When installing the light on a vehicle, you MUST use the manufacturer’s supplied mounting gasket, screws, and screw grommets. Do not use an impact drill or an electric screw gun when installing the light. Torque the mounting screws to the manufacturer’s recommended specification of 7.8-11.3 in-lb. -
Page 9: Figure 3 Exploded View - With Bezel
Installing the FireRay Figure 3 Exploded view - with bezel Figure 4 Base Installallation and Maintenance Instructions Federal Signal www.fedsig.com... - Page 10 Installing the FireRay FireRay Utility Light ® Federal Signal www.fedsig.com...
-
Page 11: Making Electrical Connections
Making Electrical Connections Making Electrical Connections The FireRay utility light heads assembly operates on 12 Vdc. Two, three or four 7.8” long lead wires are supplied for making electrical connections to the FireRay utility light heads assembly. Ensure that all wires are properly connected and insulated appropriately. -
Page 12: Table 3 Turn Arrow Patterns
Making Electrical Connections NOTE: This unit may not be factory set at FP#1 For Turn Arrow Lamp • Red: To +Vdc for Turn Signal (Suggested Fuse Rating 1 A) • Black: To -Chassis Ground • Yellow: For Synchronization, Turn Arrow Pattern Connect YELLOW wires of all light heads together for synchronization(all light heads should be set at the same pattern) -
Page 13: Figure 5 Light Orientation
Making Electrical Connections during installation. Figure 5 Light Orientation Installallation and Maintenance Instructions Federal Signal www.fedsig.com... -
Page 14: Maintaining The Light Head
Maintaining the Light Head Maintaining the Light Head CLEANING POLYCARBONATE DOMES AND LENSES: Crazing (fine cracks) of lenses causes reduced effectiveness of the light. Do not use cleaning agents (which causes crazing) such as strong detergents, solvents, or petroleum products. If crazing of lenses does occur, reliability of light for emergency signaling purposes may be reduced until lenses are replaced. -
Page 15: Getting Technical Support
Getting Repair Service Getting Technical Support For technical support, please contact: Federal Signal Corporation Phone: 1-800-443-9132 Fax: 1-800-343-9706 Email: empserviceinfo@fedsig.com Getting Repair Service The Federal Signal factory provides technical assistance with any problems that cannot be handled locally. Any units returned to returned to Federal Signal for service, inspection, or repair must be accompanied by a Return Material Authorization (RMA). - Page 16 2645 Federal Signal Drive University Park, Illinois 60484 www.fedsig.com Customer Support Police/Fire-EMS: 800-264-3578 • +1 708 534-3400 Work Truck: 800-824-0254 • +1 708 534-3400 Technical Support 800-433-9132 • +1 708 534-3400...
Need help?
Do you have a question about the FireRay Utility Light and is the answer not in the manual?
Questions and answers