Summary of Contents for IAC INDUSTRIES Quick Value AMERICAN Series
Page 1
INDUSTRIES Quick Value AMERICAN SERIES 915 ADJ. BENCHES IAC INDUSTRIES 3831 S BULLARD AVE., GOODYEAR, AZ 85338 Phone (714) 990-8997 Fax (714) 990-0557 www.iacindustries.com 915 HAND CRANK ADJ. HI Assembly Instructions REV. (010019P65)
Page 2
If you believe there are parts missing from your order please contact IAC Industries customer service at 800-989-1422. WARNING: ALL PARTICLE BOARD USED IN IAC INDUSTRIES PRODUCTS ARE SOURCED ONLY FROM VENDORS THAT ARE CARB ATCM PHASE 2 AND TSCA TITLE VI COMPLIANT WITH VALID CERTIFICATES Drilling, Sawing, Sanding or Machining Wood products can expose you to wood dust, a substance known to the state of California to cause cancer.
Page 3
Parts List: 915 Hand Crank Adjustable Bench (Ref. Figure 1) Item Description Qty. Item Description Qty. Work surface Bolt, ¼-20 x .750 SQH Black GR2 930 Leg Sub-Assy-Rt & Lt Screw, 10-32 x 3.00 PHP Black Front Support Beam 1.5H Washer, #10 Flat Zinc 930 Modesty Panel 930/940 Nut, #10-32 Hex Keps Black...
Page 4
Reference Assembly Drawing below: It may take as many as 4 people to assemble this bench. Place worksurface (item 1) on clean surface underside facing up to be installed later. Install the four floor glides (item J) and the four black bottom end cap (item H) to each end of the leg assemblies.
Page 5
lace the worksurface on top of the frame and loosely attach it to the beam and pedestal legs using the #14AB x .625 screws (Item P) and 1/4 washers (Item B) screwed into the 3/16 pilot holes drilled in the bottom of the worksurface. Do not tighten completely as some adjustment will be needed later Loosely attach hand crank rear mounting bracket (item K) to the rear of pump system using10-32 x 3.00 phillips screw (item E), #10 Washer (item F) and Nut, #10-32 Hex Keps...
ESD GROUNDING: (HWR-014) ESD refers to the OPTIONAL static dissipative laminate used on the bench. The laminate has a conductive under layer that comes in contact with the factory installed grounding bolts in the worksurface. The ESD grounding kit, including the 10 ft. grounding wire must be attached and the bench must be properly grounded to your facility earth ground.
Page 7
Grounding Cautions (Continued) ………….. 5.) DON’T use power tools to install the nuts for the grounding kit. HAND TIGHTEN ONLY. If you attempt to 'spin' the ground bolt, the serrated teeth under the head of the bolt might strip the thin conductive layer.
Page 8
INDUSTRIES Quick Value QV AMS 925 Motorized Adjustable Bench IAC INDUSTRIES 3831 S BULLARD AVE., GOODYEAR, AZ 85338 Phone (714) 990-8997 Fax (714) 990-0557 www.iacindustries.com QV925 HAND CRANK ADJ. HI Assembly Instructions REV. (042318P65)
Page 9
Cleaning ATTENTION NOTES: IAC Industries takes great care in the packing of its products; however damage can occur during shipment. Check all packages and parts for any signs of damage. If damage is evident STOP and contact the carrier that delivered your order. Request a freight claim inspector to document the damage and begin the freight claim process.
Page 10
Parts List: 925 Motor Adjustable Bench (Ref. Figure 1) Item Description Qty. Item Description Qty. Work surface Bolt, ¼-20 x .750 SQH Black GR2 940 Leg Sub-Assy-Rt & Lt Screw, 10-32 x 3.00 PHP Black Front Support Beam 1.5H Washer, #10 Flat Zinc 930/940 Modesty Panel Nut, #10-32 Hex Keps Black Cap, 2.00 x 3.00 10-14 GA Black...
Page 11
Reference Assembly Drawing below: It may take as many as 4 people to assemble this bench. Place worksurface (item 1) on clean surface underside facing up to be installed later. Install the four floor glides (item J) and the four black bottom end cap (item H) to each end of the leg assemblies.
Page 12
Install the Motor Cover / Pump to the back of the Modesty Panel. There are five threaded inserts in the front of the Motor Cover that line up with five slots on the Modesty Panel. Attach with five 1/4-20 x .75 hex head bolts (Item A) and 1/4 flat washers (Item B). Place the worksurface on top of the frame and loosely attach it to the beam and pedestal legs as well as the three screws for the motor cover using the #14AB x .625 screws (Item P) and 1/4 washers (Item B) screwed into the 3/16 pilot holes drilled in the bottom of the...
Page 13
Mount the motor switch at this point. Install the switch to the front beam using two #10-32 screws (Item E) and #10-32 nuts (Item F) and #10 flat washers (item G). Raise the leg assemblies to their highest point by using the motor control switch . Secure the motorize pump hydraulic lines to underside of worksurface using cable mounts (items M), cable ties (items N) and #6x.500 Phillips Screws (items L) being sure not to kink or damage the lines in anyway.
Page 14
ESD GROUNDING: HWR014 ESD Hardware Kit ESD refers to the OPTIONAL static dissipative laminate used on the bench. The laminate has a conductive under layer that comes in contact with the factory installed grounding bolts in the worksurface. The ESD grounding kit, including the 10 ft. grounding wire must be attached and the bench must be properly grounded to your facility earth ground.
Page 15
Grounding Cautions (Continued) ………….. 5.) DON’T use power tools to install the nuts for the grounding kit. HAND TIGHTEN ONLY. If you attempt to 'spin' the ground bolt, the serrated teeth under the head of the bolt might strip the thin conductive layer.
Page 16
INDUSTRIES Quick Value ALL AMERICAN SERIES WORK BENCHES IAC INDUSTRIES 3831 S BULLARD AVE., GOODYEAR, AZ 85338 Phone (714) 990-8997 Fax (714) 990-0557 www.iacindustries.com QS Value Line DWR Assembly Instructions REV. (042318P65)
Page 17
Please look for these instructions while unpacking. ATTENTION NOTES: IAC Industries takes great care in the packaging of its products; however damage can occur during shipment. Check all packages and parts for any signs of damage. If damage is evident STOP and contact the carrier that delivered your order. Request a freight claim inspector to document the damage and begin the freight claim process.
Your bench has been carefully packed at the factory to prevent damage during shipment. Unpack all parts and examine them for damage. Contact your freight carrier for freight claims information if your order was shipped "freight collect" or "pre-pay and add". Contact IAC Industries at 800 989-1422 if parts are missing. TOOLS NEEDED: Power or hand held Phillips head screwdriver with #2 tip, 7/16"...
Page 19
Note: Applies to all drawer and suspended cabinet configurations. It is best to install drawer bracket and drawer(s) while bench in upside down. Step 1: Install rear mounting bracket to worksurface as shown on below using hardware listed above. Note: The position of your bracket will be determined by the size of your front beam. Remove drawer from drawer case by pulling the drawer body out of the case.
Page 20
Cylinder Lock Bill Of Materials Lock Retainer Lock Body Two Keys Lock Bill of Materials Description Lock Retainer Lock Body Set Of Lock Keys...
Page 21
QV-All American Series Lock Assembly Step 1-.Insert Lock body into drawer face. Making sure the back of the lock is facing in the upward direction. You may do this with the keys already inside the lock itself. Once the lock body is in place, use the clip lock retainer provided to hold the lock in place.
Page 22
INDUSTRIES Quick Value ALL AMERICAN SERIES ELECTRICAL IAC INDUSTRIES 3831 S BULLARD AVE., GOODYEAR, AZ 85338 Phone (714) 990-8997 Fax (714) 990-0557 www.iacindustries.com QS Value Line Assembly Instructions REV. (042318P65)
Page 23
Please look for these instructions while unpacking. ATTENTION NOTES: IAC Industries takes great care in the packaging of its products, however damage can occur during shipment. Check all packages and parts for any signs of damage. If damage is evident STOP and contact the carrier that delivered your order. Request a freight claim inspector to document the damage and begin the freight claim process.
Page 24
Your bench has been carefully packed at the factory to prevent damage during shipment. Unpack all parts and examine them for damage. Contact your freight carrier for freight claims information if your order was shipped "freight collect" or "pre-pay and add". Contact IAC Industries at 800 989-1422 if parts are missing. Mounting Plate Screws...
Page 25
QS-All American Series Electrical Follow Steps 1 and 2 to install mounting bracket to worksurface. PLEASE NOTE: (If installing electrical channel on the underside of worksurface) Place worksurface top side down on smooth flat surface being sure to protect it from damage by foreign objects.
Page 26
QS-All American Series Electrical Finished assembly shown below:...
Page 27
INDUSTRIES Quick Value ALL AMERICAN SERIES INSTRUMENT SHELVES IAC INDUSTRIES 3831 S BULLARD AVE., GOODYEAR, AZ 85338 Phone (714) 990-8997 Fax (714) 990-0557 www.iacindustries.com QV Value Line Assembly Instructions REV. (042318P65)
Page 28
ATTENTION NOTES: IAC Industries takes great care in the packaging of its products; however damage can occur during shipment. Check all packages and parts for any signs of damage. If damage is evident STOP and contact the carrier that delivered your order. Request a freight claim inspector to document the damage and begin the freight claim process.
Page 29
Your bench has been carefully packed at the factory to prevent damage during shipment. Unpack all parts and examine them for damage. Contact your freight carrier for freight claims information if your order was shipped "freight collect" or "pre-pay and add". Contact IAC Industries at 800 989-1422 if parts are missing. HARDWARE KIT HWR4011: Screw, ¼-20 X .500 PPH F Blk...
Page 30
QV-All American Series Instrument Shelves Place Instrument Shelf work surface top side down on smooth flat surface being sure to protect it from damage by foreign objects. IAC recommends the use of packing type blankets or clean cardboard. Step 1: Place the instrument shelf upside down on smooth flat surface being sure to protect it from damage by foreign objects.
Page 31
INSTRUMENT SHELF HOLE PATTERN The figure below shows the hole pattern for the riser box. You need to drill two 3/16ths holes. The first hole is 3 inches from the end of the work surface and 3 inches from the top of the work surface. The second hole is also 3 inches from the end of the work surface;...
Page 32
ESD Grounding HARDWARE KIT HWR 122 Note: do not use power tools for installation of ground cords. Step 1: For ESD work surfaces and instrument shelves to dissipate static electricity they require the connection of a ground cord to an earth ground. IAC install grounding studs on each rear corner of all ESD work surfaces and instrument shelves as well as insulation strips between work surface and riser boxes.
Page 33
INDUSTRIES Quick Value ALL AMERICAN SERIES Slotted Uprights IAC INDUSTRIES 3831 S BULLARD AVE., GOODYEAR, AZ 85338 Phone (714) 990-8997 Fax (714) 990-0557 www.iacindustries.com QV Value Line Assembly Instructions REV. (042318P65)
Page 34
ATTENTION NOTES: IAC Industries takes great care in the packaging of its products; however damage can occur during shipment. Check all packages and parts for any signs of damage. If damage is evident STOP and contact the carrier that delivered your order. Request a freight claim inspector to document the damage and begin the freight claim process.
Page 35
Your bench has been carefully packed at the factory to prevent damage during shipment. Unpack all parts and examine them for damage. Contact your freight carrier for freight claims information if your order was shipped "freight collect" or "pre-pay and add". Contact IAC Industries at 800 989-1422 if parts are missing. HARDWARE KIT QV-HWR4101: Cap 1.25 x 2”...
Page 36
QV-All American Series Upright Assembly NOTE: Drawing below shows the assembly of the uprights to the bench with just the rear leg supports of the bench for assembly purposes, it is recommended that you install the uprights after the assembly of your bench.
Page 37
Below is the hole pattern for the uprights. PLEASE NOTE: THIS HOLE PATTERN APPLIES TO BOTH SIDES OF THE WKSF, SO A TOTAL OF 4 HOLES WILL NEED TO BE DRILLED.
Page 38
INDUSTRIES Quick Value ALL AMERICAN SERIES SHELF 915-925 IAC INDUSTRIES 3831 S BULLARD AVE., GOODYEAR, AZ 85338 Phone (714) 990-8997 Fax (714) 990-0557 www.iacindustries.com QV Value Line Assembly Instructions REV. (042318P65)
Page 39
ATTENTION NOTES: IAC Industries takes great care in the packaging of its products; however damage can occur during shipment. Check all packages and parts for any signs of damage. If damage is evident STOP and contact the carrier that delivered your order. Request a freight claim inspector to document the damage and begin the freight claim process.
Page 40
Your bench has been carefully packed at the factory to prevent damage during shipment. Unpack all parts and examine them for damage. Contact your freight carrier for freight claims information if your order was shipped "freight collect" or "pre-pay and add". Contact IAC Industries at 800 989-1422 if parts are missing. HARDWARE KIT QS-HWR4021: BRKT, VL Shelf 10.25L RT...
Page 41
QV-All American Series Shelf Assembly Step 1- First, insert the Nuts, Unistrut ¼-20 Short Spring provided to the bottom of the shelf body, once they set in the shelf body align the holes of the Spring nuts with the slots on the VL Shelf Brkts and use the Bolts, ¼-20 X .75 HHW BLK provided to connect the brackets to the shelf body.
Page 42
ESD Grounding HARDWARE KIT HWR115 - HWR014 (Reference only) Note: do not use power tools for installation of ground cords. Step 1: For ESD work surfaces and instrument shelves to dissipate static electricity they require the connection of a ground cord to an earth ground. IAC install grounding studs on each rear corner of all ESD work surfaces and instrument shelves as well as insulation strips between work surface and riser boxes.
Page 43
INDUSTRIES Quick Value ALL AMERICAN SERIES BIN RAIL IAC INDUSTRIES 3831 S BULLARD AVE., GOODYEAR, AZ 85338 Phone (714) 990-8997 Fax (714) 990-0557 www.iacindustries.com QV Value Line Assembly Instructions REV. (042318P65)
Page 44
ATTENTION NOTES: IAC Industries takes great care in the packaging of its products; however damage can occur during shipment. Check all packages and parts for any signs of damage. If damage is evident STOP and contact the carrier that delivered your order. Request a freight claim inspector to document the damage and begin the freight claim process.
Page 45
Your bench has been carefully packed at the factory to prevent damage during shipment. Unpack all parts and examine them for damage. Contact your freight carrier for freight claims information if your order was shipped "freight collect" or "pre-pay and add". Contact IAC Industries at 800 989-1422 if parts are missing. QV-All American Series BIN RAIL Step 1- Snap into slotted posts at desired height.
Page 46
INDUSTRIES Quick Value ALL AMERICAN SERIES SLOTTED UPRIGHT LIGHT FIXTURE IAC INDUSTRIES 3831 S BULLARD AVE., GOODYEAR, AZ 85338 Phone (714) 990-8997 Fax (714) 990-0557 www.iacindustries.com QV Value Line Assembly Instructions REV. (042318P65)
Page 47
ATTENTION NOTES: IAC Industries takes great care in the packaging of its products; however damage can occur during shipment. Check all packages and parts for any signs of damage. If damage is evident STOP and contact the carrier that delivered your order. Request a freight claim inspector to document the damage and begin the freight claim process.
Page 48
Your bench has been carefully packed at the factory to prevent damage during shipment. Unpack all parts and examine them for damage. Contact your freight carrier for freight claims information if your order was shipped "freight collect" or "pre-pay and add". Contact IAC Industries at 800 989-1422 if parts are missing. HARDWARE KIT QV-HWR4055: Bolt, 1/4-20 X 1.00 HH BLACK...
Page 49
QV-All American Series LT Light Fixture Assembly Step 1- Read the Note below before continuing. Once the Bolts, 1/4-20 X 1.00 HH BLACK and 1/4 flat washers have been threaded through the slots in the light fixture, proceed to feed the Nut, 1/4-20 UNISTRUT SHORT SPRING N-5 into the sides of the unistrut channel by compressing the spring and rotating the nut inside the channel until it sets along the inside of the channel.
Page 50
INDUSTRIES Quick Value ALL AMERICAN SERIES FPD SWING ARM UNIVERSAL SPM IAC INDUSTRIES 3831 S BULLARD AVE., GOODYEAR, AZ 85338 Phone (714) 990-8997 Fax (714) 990-0557 www.iacindustries.com QV Value Line Assembly Instructions REV. (042318P65)
Page 51
ATTENTION NOTES: IAC Industries takes great care in the packaging of its products; however damage can occur during shipment. Check all packages and parts for any signs of damage. If damage is evident STOP and contact the carrier that delivered your order. Request a freight claim inspector to document the damage and begin the freight claim process.
Page 52
Your bench has been carefully packed at the factory to prevent damage during shipment. Unpack all parts and examine them for damage. Contact your freight carrier for freight claims information if your order was shipped "freight collect" or "pre-pay and add". Contact IAC Industries at 800 989-1422 if parts are missing. HARDWARE KIT QS-HWR4122: KNOB,TRI-WHEEL 1/4"...
Page 53
QV-All American Series QV American Series Swing Arm FPD Step 1- First; feed Carriage Bolts through rear of both brackets provided (confirm which bracket is FRONT and REAR), making sure the Carriage Bolts snap into place. Next, feed the Carriage Bolts through the swing arm assembly.
Page 54
INDUSTRIES Quick Value ALL AMERICAN SERIES FPD KEYBOARD HOLDER IAC INDUSTRIES 3831 S BULLARD AVE., GOODYEAR, AZ 85338 Phone (714) 990-8997 Fax (714) 990-0557 www.iacindustries.com QV Value Line Assembly Instructions REV. (042318P65)
Page 55
ATTENTION NOTES: IAC Industries takes great care in the packaging of its products; however damage can occur during shipment. Check all packages and parts for any signs of damage. If damage is evident STOP and contact the carrier that delivered your order. Request a freight claim inspector to document the damage and begin the freight claim process.
Page 56
Your bench has been carefully packed at the factory to prevent damage during shipment. Unpack all parts and examine them for damage. Contact your freight carrier for freight claims information if your order was shipped "freight collect" or "pre-pay and add". Contact IAC Industries at 800 989-1422 if parts are missing. HARDWARE KIT QS-HWR4025: SCREW, 10-32 X .625 PPH ZINC WASHERS, #10 FLAT ZINC...
Page 57
QV-All American Series Flat Panel Display Keyboard Assembly Step 1- Insert the keyboard bracket shown from the bottom of the tray up into the opening and mount it by using SCREW; 10-32 X .625 PPH ZINC, Washer #10 and Nut #10-32.Make sure all hardware is tightened and secure.
Page 58
INDUSTRIES Quick Value ALL AMERICAN SERIES DOCUMENT HOLDER SPM IAC INDUSTRIES 3831 S BULLARD AVE., GOODYEAR, AZ 85338 Phone (714) 990-8997 Fax (714) 990-0557 www.iacindustries.com QV Value Line Assembly Instructions REV. (042318P65)
Page 59
ATTENTION NOTES: IAC Industries takes great care in the packaging of its products; however damage can occur during shipment. Check all packages and parts for any signs of damage. If damage is evident STOP and contact the carrier that delivered your order. Request a freight claim inspector to document the damage and begin the freight claim process.
Page 60
Your bench has been carefully packed at the factory to prevent damage during shipment. Unpack all parts and examine them for damage. Contact your freight carrier for freight claims information if your order was shipped "freight collect" or "pre-pay and add". Contact IAC Industries at 800 989-1422 if parts are missing. HARDWARE KIT QV-HWR4116: Knob, Tri-Wheel 1/4-20 1/4"...
Page 61
TOOLS NEEDED: Power or hand held Phillips head screwdriver with #2 tip, 7/16" and 1/2" combination wrench or thin wall sockets. QV-All American Series Document Holder SPM Assembly Step 1- First, place the AMS FPD SPM FRT (square slots) BEHIND the AMS FPD SPM REAR bracket, thread the Bolt, 1/4-20x.750 Carriage through the brackets and also the swing arm mount.