Jacuzzi J-400 Series Installation Manual And Use & Maintenance page 59

The "Settings 2" Menu will appear.
A
Primary
Secondary
2
B
3
Note: You can return to the factory default filtration modes by
pressing the Splash button on the Quad Keypad while in the
Settings 2 Main Menu at any time.
Primary Filter Cycle: Press button A to access the Pri-
mary filtration submenus.
Secondary Filter Cycle: Press button C to access the
Secondary filtration submenus.
3
Settings 3 Menu: Press button B to access the "Set-
tings 3" Submenus.
Previous: Press button D to go to the previous menu.
I
Programming the Primary Filter Cycle
To program the Primary Filter cycle press button A. This cycle
is mainly used to alter the pre-programmed 12-hour running
period of the circulation pump. The 12-hour cycle is from
12:00 AM to 12:00 PM. (If you would like to leave the circu-
lation pump as is, then skip this section). Upon entering the
Primary submenu the "Start Time" will be selected.
PRIMARY
Start Time
Start Time
1PM
Select
Duration
3
Press to Save
I
Press the Left or Right button on the Quad Keypad to choose
the hour you want the circulation pump to start running.
Note: If you are using a standard 12-hour period, you will
see the hour displayed as "1PM." For the 24-hour period it will
read "1300."
I
Now you will need to adjust the "Duration" of the cycle.
Press the Down button to select "Duration." Press the Left or
Right button on the Quad Keypad to make adjustments in in-
crements of 1 hour. Press the Splash button on the Quad Key-
pad to save hour and duration selections and return to the Set-
tings 2 Main Menu.
SETTINGS 2
C
OFF
OFF
D
Press to
reset to default
PRIMARY
Start Time
Duration Duration 12hr
3
Press to Save
Summer Logic:
In warm weather, the water temperature in the spa may exceed the
set temperature. This condition may occur due to heat transference
from the filter/circulation pump and jets pumps. If the water tem-
perature is higher than 35°C and rises two degrees above the set
temperature, a "Summer Logic" condition occurs that deactivates
the filter/circulation pump and CLEARRAY™. This safety feature
cannot be altered! The filter/circulation pump and CLEARRAY™
will remain off until the water temperature cools to the set temper-
ature (except between 9am-11am when the filter/circulation pump
runs for it's mandatory 2 hour cycle.) To help prevent a "Summer
Logic" condition, it may be necessary to reduce filter/circulation
pump cycles run times in warm weather.
Programming the Secondary Filter Cycle
To program the Secondary Filter cycle, press button C. This
cycle will activate the main jet pump to run for additional fil-
tration when programmed. If you choose not to use this fea-
ture, please skip this section.
SETTINGS 2
Primary
Secondary
OFF
2
3
Press to
reset to default
When you enter the Secondary Filter Cycle submenu, the
"Day Settings" will be selected. From this menu, you can set
the day, time, and duration. Press the Splash button on the
Quad Keypad to confirm selection.
You can choose the day(s) you would like to run a secondary
filter cycle. Press the Up or Down button on the Quad Keypad
to scroll through and change the days you would like the fil-
tration to run. Press the Left or Right button to turn "ON" (
) or "OFF" the filtration for that day.
SECONDARY
Monday OFF
Tuesday OFF
Wednesday OFF
Thursday OFF
Friday OFF
Saturday OFF
Sunday OFF
3
Press to Enter
Press the Splash button to save settings.Then the display will
revert to the Secondary Program Menu.
Press button D to return to the submenu to continue pro-
gramming the start time and duration.
Press the Down button on the Quad Keypad to select "Start
Time". Press the Left or Right button on the Quad Keypad to
select the time you wish the spa to filter. Press the Down but-
ton on the Quad keypad to access the "Duration" setting.
59
Select
SECONDARY
Day Settings Day Settings
Start Time
Duration
3
Press to Enter
Select
Select