Settings 2 Menus - Jacuzzi J-400 Series Installation Manual And Use & Maintenance

the spa to run. Press the Down button on the Quad keypad to
access the "Duration" setting.
PROGRAM B
Day Settings
Start Time Start Time 1PM
Select
Duration
B
Press to Save
2
Note: If you are using a standard 12-hour period, you will
see the hour displayed as "1PM." For the 24-hour period it will
read "1300."
I
Now you will need to adjust the "Duration" of the cycle. The
duration range is from 0 (OFF) to 6 hours. Press the Left or Right
button on the Quad Keypad to make your adjustment (s) in in-
crements of 1 hour.
PROGRAM B
Day Settings
Start Time
Select
Duration Duration
OFF
B
Press to Save
2
Note: The default "Duration" is OFF.
Press the Splash button on the Quad Keypad to save your
changes and return to the Heating Menu.
Press button D to exit the Heating Menu and return to the Set-
tings 1 Main Menu. If you have programmed both heating cycles
and the settings have been accepted, you will see the two pro-
gram icons next to word Heating on the display. If only one cy-
cle was programmed, there will only be one icon.
SETTINGS 1
Heating
A B
UV Light
0 Days
1
Filter
OFF
Press to
2
set filter or UV timer
Clean-Up "Blow-Out" Cycle
The clean-up cycle occurs once per day in all Heating modes at
12:00 (noon) for two minutes. This is not user programmable.
Each jets pump activates for one minute to circulate any water
in the plumbing unless a pump has just finished a 20 minute time
out, it will not automatically activate for the clean-up cycle. Be
aware, the factory programmed clean-up cycle cannot be can-
celed or altered!
I
Programming the CLEARRAY™ timer
Use the Quad Keypad down button to select "UV Light. " After the
"UV Light" selection is active, press the Splash button to acti-
vate the "UV timer".
SETTINGS 1
Heating
ENERGY EFFICIENT
UV Light
0 Days
1
Filter
OFF
Press to
2
set filter or UV timer
SETTINGS 1
Heating
ENERGY EFFICIENT
UV Light
365 Days
1
Filter
OFF
2
Press the Left button on the Quad Keypad to set the "UV timer"
to 365 days.
Note: The UV timer counts down by days not usage. The days
are store in memory if the power is interrupted. The timer will
only reset once it counts down to "0 days".
When the timer expires, a message will appear on the Main Menu
display. The UV bulb must be replaced and the timer must be re-
set. Just follow the instructions above to reset the UV timer.
Note: When the timer expires, the indicator light will turn red.
The bulb must be replaced and the timer reset. To reset the
timer prior to the 365 days, press and hold the Uo button. Then
press the Left or Right buttons in increments of 10 days.
I
Setting the Check Filter Reminder
Use the Quad Keypad down button to select Filter. After "Filter"
selection is active, press the Splash button to access the "set fil-
ter timer".
SETTINGS 1
Heating
ENERGY EFFICIENT
UV Light
0 Days
1
Filter
OFF
Press to
2
set filter or UV timer
Press the Left or Right button on the Quad Keypad to scroll the
number of days you would like the reminder to appear so the fil-
ters and polishing bag can be cleaned or replaced.
Press the Splash button to confirm and save your selection.
When the set time period expires, the "Please check filter!" mes-
sage will appear on the Main Menu display. The reminder must
be reset when the time allotted expires.
Note: The time range is from 10 to 365 days in increments of
10 days or you can elect to turn the feature "OFF."

Settings 2 menus

Programming Instructions for Settings 2 Menus
The "Settings 2" screen allows you to program the Primary Fil-
ter mode, Secondary Filter mode and access the "Settings 3"
Submenus.
From the "Settings 1" Menu, press button B.
A
1
B
2
58
SETTINGS 1
Heating
ENERGY EFFICIENT
UV Light
365 Days
1
Filter
0 Days
Press to
2
save settings
SETTINGS 1
Heating
ENERGY EFFICIENT
UV Light
0 Days
Filter
OFF
D
Press to
set filter or UV timer
C