Subscribe to Our Youtube Channel
Related Manuals for SOMFY WireFree Solar Pack
Summary of Contents for SOMFY WireFree Solar Pack
- Page 1 Roller Shade Installation Instructions Standard Installation p - 2 - Cordless Installation p - 6 - Cassette Installation p - 10- Motorization Solar Panel Installation p - 12 - Motorization Remote Control Programming p - 20 -...
- Page 2 Parts Listing 1. Continuous Loop Shade Chain Guide Mounting Brackets Optional Items Bracket Covers Channel Valance v� Sa. Valance Corners � Sb. Valance Returns Sc. Valance Mounting Brackets � 6. Hold Down Brackets / r«:'J: Valance Bracket Chart (Outside Mount Only) Ordered Width Brackets up to 36"...
- Page 3 Take the valance down from the window and turn upside down. Brackets for inside mount can be Side Mount Ceiling/Top Mount Measure 6" in from each end and oriented for side, ceiling or top a minimum of 1/2" up and mark mounting to the window frame.
- Page 12 Instruction Booklet WireFree Solar Pack #9015575...
-
Page 13: Parts Overview
This product is designed to meet the energy requirements for new and existing Somfy 12 Volt WireFree motorized window coverings, and should not be used in conjunction with any other motor systems. - Page 14 (NOTE: Lithium battery tubes are not compatible with Solar Pack) NOTE: Battery should be fully charged prior to installation with battery charger (Somfy Item #9015781) sold separately. The following depicts the most common installation options, however the battery tube may be installed in a location that is most convenient.
- Page 15 Step 2: Installing Solar Panel Determine the location of the Solar Panel • The Solar Panel must always be installed INDOORS, in most cases, directly against the window glass to ensure maximum exposure to sunlight NOTE: To prevent damage to Solar Panel and/or window hardware, DO NOT MOUNT Solar Panel directly to window glass if it will cause an obstruction to moveable window frames and hardware! • Optional: Solar Panel should be mounted on the same side as the battery tube (see Option 1 and 2).
- Page 16 Step 3: Installing Solar Panel to Window Glass Clean Solar Panel frame and proposed window glass location with alcohol prep pad (included). Let dry for 2 minutes. Position Solar Panel “face-up” and apply the adhesive tape to (4) corners of the Solar Panel frame (See Figure 2).
-
Page 17: Motor Connector
Step 4: Connecting Solar Panel and Battery Tube Connect Wire Harness Motor Connector to motorized window covering. Connect Battery Tube to Wire Harness. Connect Solar Panel to Wire Harness. Solar Panel and Battery Tube Connectors Motor Connector Motorized Blind Window Covering Battery Tube Wire Harness Solar Cell... - Page 18 Step 5: Commissioning Motorized Window Covering ACTIVATION OF MOTORIZED WINDOW COVERING: • New Installations: Please reference Window Covering Product Guide (Usually included with Motorized Window Covering) for instructions on initial activation and/or programming of product. • Existing Installations: Simply operate the window covering as normal. Once initial command (UP and DOWN) is sent, window covering will respond with a brief “jog,”...
- Page 19 (P) 561 995 8376 (F) 561 995 7502 California 15291 Barranca Pkwy Irvine, CA 92618 (P) 877 727 6639 (F) 949 727 3775 Somfy Canada 5178 Everest Drive Mississauga, Ontario L4W2R4 CN 905-564-6446 (F) 905-238-1491 C-0025 © Copyright Somfy Systems, Inc. 10/2012...
- Page 20 Roll Up WireFree RTS Programming & Operation Instructions LT-30RT Round Head Before you begin Motors are shipped without limit switch settings and transmitter ID’s Steps (1-6) must be completed to ensure proper shade programming and functionality. It may be necessary to disconnect shades from their respective power while programming is in progress.
- Page 21 Roll Up WireFree RTS Programming & Operation Instructions LT-30RT Round Head STEP THREE Check Polarity (Shade direction) MUST BE DETERMINED BEFORE SETTING SHADE LIMITS Press and Press and hold the DOWN utton and confirm the shade moves down. hold DOWN Button Press and hold the UP utton and confirm the shade moves up.
- Page 22 Roll Up WireFree RTS Programming & Operation Instructions LT-30RT Round Head STEP FOUR Setting Limits (Shade Positions) continued. Once shade stops at previously set lower limit (shade position), press the MY (stop) utton for 2 seconds until the shade jogs. This confirms both limits (shade positions).
- Page 23 Roll Up WireFree RTS Programming & Operation Instructions LT-30RT Round Head Completing & Exiting Programming Mode STEP FIVE Program Program Program Using a paperclip, press and hold the PROGRAM utton Button Button Button on the back of the transmitter until the shade jogs. TRANSMITTER IS NOW MEMORIZED AND PROGRAMMING IS COMPLETE.
- Page 24 Roll Up WireFree RTS Programming & Operation Instructions LT-30RT Round Head STEP SIX Adding Additional Transmitters, Assigning or Deleting Channels (continued). Deleting Specific Channels/Transmitters 1) Using a paperclip, press and hold the PROGRAM utton on the previously addressed transmitter until the shade jogs. Previous 2) Select the desired channel (1-4 or all) or transmitter (single channel) to be deleted.
- Page 25 Roll Up WireFree RTS Programming & Operation Instructions LT-30RT Round Head Setting an Intermediate Position (IP) continued. OPTION ONE 2) Once the desired Intermediate position is reached, Press and hold the MY (stop) utton on the transmitter until the shade jogs. Intermediate position is now added to memory Press &...
- Page 26 2) Press and hold the DOWN utton on the transmitter until shade begins to “step” or tilt. 3) Release the DOWN utton on the transmitter once new position is reached. NOTE: Shade must be already programmed to activate tilting feature. SOMFY SYSTEMS, INC. 2/07 REV.1...
Need help?
Do you have a question about the WireFree Solar Pack and is the answer not in the manual?
Questions and answers