CONTENTS FEATURES ........................1 SPECIFICATIONS ......................2 BATTERY REPLACEMENT ..................4 REPLACING THE BACK-UP BATTERY ..............4 RESET OPERATION ..................... 5 TO SAVE THE DATA TO ANOTHER UNIT ..............6 BLOCK DIAGRAM ......................8 TOUCH PANEL CIRCUIT....................9 PIN FUNCTION......................10 DIAGNOSTIC PROGRAM ...................
• 256 kbytes (NX-6000) / 128 kbytes (NX-4000) of memory You get enough memory to store up to 11,100 (NX-6000) / 5,200 (NX-4000) Telephone Directory items. • Powerful data bank functions Telephone Directory, Business Card Directory, Memo, Sketch, To Do, Expense Manager, Reminder, and Schedule Keeper are at your fingertips throughout the day.
SPECIFICATIONS Storage Capacity The 256K (NX-6000) / 128K (NX-4000) bytes memory capacity includes a 245,709 / 114,637-byte user area. The following shows examples of what this means for the storage of data in each mode. Telephone Directory Approximately 11,100 / 5,200, under the following conditions:...
Page 5
10-character description Expense type and Payment type set General: 21-column × 8-line LCD Display element: Memory capacity: 256 KB (NX-6000), 128 KB (NX-4000) Main component: Power supply: Main: Two AAA-size batteries (Type: R03 (UM-4) or LR03 (AM4)) Back-up: One CR2032 lithium battery...
BATTERY REPLACEMENT 1. Switch power off. 2. Slide the battery compartment cover in the direction indicated by the arrow. 3. Slide the battery switch in the direction indicated by the arrow in the illustration. 4. Remove the main battery holder. 5.
4. Remove the old battery and replace it with new one, making sure that the positive (+) side of the new battery is facing up (so you can see it). 5. Replace the back-up battery holder and secure it by tightening its screw. •...
Input mode: Overwrite TO SAVE THE DATA TO ANOTHER UNIT NX-4000/6000 can transfer customer's data to another NX-4000/6000 with memory protection only when replacing the LCD or the outer case. How to transfer the data 1) Make sure that the power of both units is switched off.
Page 9
8) Set up the slave unit. Operation : MENU FUNC DATA COM. RECEIVE RECEIVE OK! DATA TO STOP PRESS [ ESC ] 9) Set up the customer's unit. • Turn the power switch off. • Press the RESET button with a thin, pointed object while shorting the following pad. Enlarge SEND ALL DATA ? BOTTOM VIEW...
TOUCH PANEL CIRCUIT Four electrodes are installed in top and bottom right and left of panel, and the touch panel recognizes the coordinate which was pushed with a pen on panel by detecting change volume of current which flowed through panel by pushing panel.
PIN FUNCTION CPU (HD62119A03) Pin No. Pin Name Input / Output Function KO12 Key common signal Switching signal for Xaxis and Y axis KO10 Strobe signal for AD converter Standby signal for AD converter Switching signal for TXR and TXL Switching signal for TYU and TYD Touch panel driving signal for TXL and TYU Touch panel driving signal for TXR and TYD...
Enter the Press on and then short SELF TEST PROG diagnostics the TEST pad. PRESS any TOUCH QUIT BY OFF KEY CASIO JULY 1995 Main menu Tap anywhere TEST MENU 1 DISPLAY 5 I / F 2 MEMORY 6 CONTRAST...
Page 14
DISPLAY N O T E 2 READ 1 Read the test pattern 1 EXECUTING !! from RAM After 3 sec. CMPLETE !! NX-4000 : 128kB XXXkB NX-6000 : 256kB Tap anywhere MEMORY 1 WRITE 1 5 DUMP 2 READ 1...
Page 15
S T E P O P E R A T I O N DISPLAY N O T E Buzzer Check 4 BUZZER 1 : Key input sound 1 BEEP 2 : Sound alarm 1 2 ALARM 1 3 : Sound alarm 2 3 ALARM 2 TEST MENU 1 DISPLAY...
Page 16
S T E P O P E R A T I O N DISPLAY N O T E TOUCH PANEL 7 TOUCH touch TEST ADJUSTMENT 1 ADJUST 2 TEST 1 ADJUST Tap the tip of the pencil icon. /////DIGITIZER////// TAP THE TIP OF THE When you do, the pencil PENCIL ICON icon you tapped...
MESSAGE TABLE Message Meaning Action NOT FOUND! Data specified in search operation does Change specification or cancel search. not exist in memory. MEMORY FULL! Not more room in memory for storage Delete unnecessary data items from of data. memory. ALARM TIME Attempt to set a Schedule Keeper, Set a different alarm time or change Reminder or a To Do alarm time that is...