Advertisement
Quick Links
®
SYSTIMAX
Solutions
SYSTIMAX
General
These instructions provide the recommended termination procedure for all SYSTIMAX
MGS600 modules are illustrated here, but instructions also apply to MGS400 and MGS500 modules. The MGS
modules are UL approved. Preparation of the new SYSTIMAX GigaSPEED
series cordage, or 91SD series cable is also shown.
GigaSPEED X10D 91B series cable, 95B series cordage or 91SD cable for termination, see instruction
sheet 860 469 402.
information.
The following tools are available to aid in module termination.
Material ID
406477794
407484971
407728427
760122713
860251081
How to Contact Us
•
To find out more about CommScope
•
For technical assistance:
-
Within the United States, contact your local account representative or technical support at
1-800-344-0223. Outside the United States, contact your local account representative or Authorized
Business Partner.
-
Within the United States, report any missing/damaged parts or any other issues to CommScope
Customer Claims at 1-866-539-2795. Outside the United States, contact your local account
representative or Authorized Business Partner.
Preparation of X10D 91B Series Cable, 95B Series Cordage, or 91SD Series Cable
for Termination
This product is covered by one or more of the following U.S. patents : 5.997.358 / 5.1.86.647 / 5.897.395
www.commscope.com
MGS Module Termination Instructions
Refer to the SYSTIMAX X10D Design and Installation Guidelines for further
Description
D-914 kit - includes impact tool and 110 blade
D-914 impact tool only
Replacement 110 blade for D-914 impact tool
Module removal tool (quantity of 5)
Hand termination tool (hand puck)
®
products, visit us on the web at
Unwind separator tape
Pull flute and tapes
off to one or more sides
© 2012 CommScope, Inc. All rights reserved
Instruction Sheet 860344274
Issue 10, October 2019 Rev B
®
X10D 91B series cable, 95B
For complete instructions on prepping the
http://www.commscope.com/
®
MGS-type modules.
Page 1 of 5
Advertisement
Related Manuals for CommScope SYSTIMAX MGS Series
Summary of Contents for CommScope SYSTIMAX MGS Series
- Page 1 1-800-344-0223. Outside the United States, contact your local account representative or Authorized Business Partner. Within the United States, report any missing/damaged parts or any other issues to CommScope Customer Claims at 1-866-539-2795. Outside the United States, contact your local account representative or Authorized Business Partner.
- Page 2 860344274 www.commscope.com Instruction Sheet Termination Procedure T568B Wiring Shown Pre-Termination Step For Angled Entry Note: Some mounting hardware and box space does not allow for cable entry directly from the rear. If a typical termination from the rear is done and the cable is then bent in the needed direction, performance and reliability can suffer.
- Page 3 860344274 Issue 9, October 2019 3. To place conductors, hold the pair down on the 4. Push conductors down into slot termination position and bend it for easy grasp as positions (check color codes). shown above. Then untwist the pair in a counter- Maintain pair twist up to the clockwise direction enough to open it up.
-
Page 4: Module Removal
860344274 www.commscope.com Instruction Sheet Note: For T568A Wiring - On each cable end, one of the two pairs fed in through the holes is pulled back for the rear positions. Check label color codes. Conductor Seating and Cutting Pliers Impact tool on HI setting... - Page 5 860344274 Issue 9, October 2019 Inspection or Repair of Termination Pivot removal tool forward Note: To enable inspection or repair, the wiring to disengage cap cap can be released from the module using the The conductors can then be removal tool.
Need help?
Do you have a question about the SYSTIMAX MGS Series and is the answer not in the manual?
Questions and answers