The Image Adjustment Menu; The Default Setting Menu; The Display Setting Menu - Toshiba TDP-D1 Owner's Manual

Using the menu (Continued)
I The image adjustment menu
Use this menu to adjust image-related items.
Items Items that can be adjusted are marked with "Yes", and those that cannot are marked
with "No".
Item Description
Contrast Lower
Brightness Darker
Color Lighter
Tint [Note 1] Reddish
Sharpness Softer
R-level Less red
G-level Less green
B-level Less blue
Up/down shift [Note 2] Shift down
Notes
1: Tint can only be adjusted when Video mode
2: Up/down shift can only be adjusted when Screen size
picture may be instability.
I The default setting menu
This menu shows placement status and other settings.
Item
Projection
Set projection mode in accordance with Placement Style
mode
(Placed
on floor)
No signal
Set the time to wait after signal input stops until turning off the power:
power off
Off (not turned off)
Power on
Set whether to turn on the power when the ON/STANDBY button is pressed
(Manual), or the main power switch is used (Auto).
Lamp power
[Note 1]
Set the lamp power
Standby mode Set standby mode according to functions used Standard
[Note 2]
Note
1: When lamp power is set to low, the screen becomes a little darker, but the cooling fan noise gets
quieter. This setting will be cleared when you turn the power off.
Notes
• Note that if Power on is set to Auto, then if the main power switch is turned on when
power is restored after a power outage, the projector power will come on.
• Even if Power on is set to Auto, press the ON/STANDBY button to turn off the power.
Turning off the main power switch to cut off the power will shorten the life of the lamp.
Computer Y/P /P Video
B R
Higher Yes Yes Yes
Brighter Yes Yes Yes
Deeper No Yes Yes
Greenish No No Yes
Sharper No Yes Yes
More red Yes Yes Yes
More green Yes Yes Yes
More blue Yes Yes Yes
Shift up No Yes Yes
p.23 is NTSC or NTSC4.43.
p.29 is Wide. During the adjustment, the
Description
p.21
(Hung from (Back hung
(Rear)
ceiling) from ceiling)
1 min 2 min ... 60 min
Manual
Standard Low
Economy
28
I The display setting menu
Use this menu to set screen display-related items.
Item
Screen size
S-video
Yes
Yes
Yes
Language
Yes
Yes
Yes
Background
Yes
Icon
Yes
Start-up screen
Yes
Note
• If "Thru" is selected for screen size, portions exceeding the native resolution will not
appear on the screen. Note that for RGB signals with clock frequency 140MHz or lower,
all input pixel signals are sampled. (This effect is noticeable when the screen is enlarged
using the Resize function
RGB pixel signal is thinned before sampling.
I Reset menu
This menu is displayed when other menus are not displayed, and the
down until the menu appears.
• When the screen is placed vertically, and Auto keystone correction is executed, but
the keystone correction is not successful, stow the foot adjuster in its original position,
place the projector on a flat surface, select Horizontal reference value reset, and press
Auto
the button.
• Select Reset All and press the
Item
Horizontal reference
value reset
Reset all
Description
(Full): Display with native resolution (1,024 x 768 pixels)
(Thru): Display with sampling resolution (for computer input)
(Wide): Wide-screen display (for Video, S-video, and Y/P
Select one of the languages below to use for displaying menus and messages
[ : Enter setting mode] [ :Selection]
English/Français/Deutsch/Italiano/Español/
Português/ / /
Screen to display when there is no input signal
Display icons as function guides
Display start-up screen when power turned on
p.36 ). However, if the clock speed is higher than this, the
(Special menu)
button to return all menu items to the factory settings.
Description
Reset the horizontal reference value for Auto keystone correction
[ : Enter execution mode] [Yes
Reset all menu items to their factory settings
[ : Enter execution mode] [Yes
29
/P )
B R
[Apply: ]
/
(Logo) (Blue) (None)
On Off
On Off
button is held
No] [Apply: ]
No] [Apply: ]