Bluetooth® Devices: Cautions - FujiFilm instax mini Link User Manual

1. Keep the film in a cool place. Do not leave the film in a place
where the temperature is extremely high (e.g., in a closed car)
for many hours.
2. Do not puncture, tear, or cut INSTAX Mini Instant Print film. If
film becomes damaged, do not use.
3. When you load a film pack, use the film as soon as possible.
4. If the film has been kept in a place where the temperature is
extremely high or low, bring it to room temperature before
loading or starting to print photos.
5. Be sure to use the film before the expiration or "Use Before"
date.
6. Avoid airport checked luggage inspection and other strong
X-ray illumination. The effect of fogging, etc. may appear on
unused film. Carrying your printer and film onto an aircraft in
your carry-on luggage is recommended. (Check with each
airport for more information.)
7. Avoid strong light, and keep the developed prints in a cool
and dry place.
8. Do not puncture or cut this film as it contains a small amount
of caustic paste (high alkaline). Never let children or animals
put the film into their mouth. Also pay attention so that the
paste does not come into contact with skin or clothes.
9. In case the paste inside the film comes into contact with skin
or clothes, immediately wash off with plenty of water. If the
paste comes into contact with the eyes or mouth,
immediately wash the area with plenty of water and contact
a doctor. Note that the alkaline inside the film remains active
for about 10 minutes after the photo has been printed.
■ Cautions on Handling the Film and Prints
See below for film activities to be avoided.
Bluetooth® Devices: Cautions
IMPORTANT: Read the following notices before using the
product's built-in Bluetooth transmitter�
■ Use only as part of a Bluetooth network�
FUJIFILM Corporation and its affiliates do not accept liability for
damages resulting from unauthorized use. Do not use in
applications requiring a high degree of reliability, for example in
medical devices or other systems that may directly or indirectly
impact human life. When using the device in computer and
14
other systems that demand a greater degree of reliability than
Bluetooth networks, be sure to take all necessary precautions to
ensure safety and prevent malfunction.
■ Use only in the country in which the device was purchased�
This device conforms to regulations governing Bluetooth
devices in the country in which it was purchased. Observe all
location regulations when using the device. FUJIFILM
Corporation and its affiliates do not accept liability for problems
arising from use in other jurisdictions.
■ Wireless data (images) may be intercepted by third parties�
The security of data transmitted over wireless networks is not
guaranteed.
Do not use the device in locations subject to magnetic fields,
static electricity, or radio interference.
■ Do not use the transmitter in the vicinity of microwave ovens
or in other locations subject to magnetic fields, static
electricity, or radio interference that may prevent reception of
wireless signals� Mutual interference may occur when the
transmitter is used in the vicinity of other wireless devices
operating in the 2�4 GHz band�
■ The Bluetooth transmitter operates in the 2�4 GHz band� The
standard output is approximately 3�16 mW�
■ This device operates on the same frequency as commercial,
educational, and medical devices and wireless transmitters�
It also operates on the same frequency as licensed transmitters
and special unlicensed low-voltage transmitters used in radio-
frequency identification tracking systems for assembly lines and
in other similar applications.
■ To prevent interference with the above devices, observe the
following precautions�
Confirm that the radio-frequency identification transmitter is
not in operation before using this device. If you notice that this
device causes interference in low-voltage radio-frequency
identification tracing systems, contact a Fujifilm representative.
■ The following may be punishable by law:
– Disassembly or modification of this device.
– Removal of device certification labels.
■ Trademark Information
The Bluetooth® word mark and logos are registered trademarks
owned by the Bluetooth SIG, Inc., and any use of such marks by
Fujifilm is under license.
For customers in the USA:
FCC Statement
This device complies with part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) This device may not
cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause
undesired operation.
For more information, access the website below.
https://www.fujifilm.com/products/instant_photo/printers/
instax_mini_link/
CAUTION
This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This
equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference