Table of Contents
Advertisement
Bluetooth® Devices: Cautions
IMPORTANT: Read the following notices before using the
product's built-in Bluetooth transmitter�
■ Use only as part of a Bluetooth network�
Do not use in applications requiring a high degree of reliability,
for example in medical devices or other systems that may
directly or indirectly impact human life. When using the device
in computer and other systems that demand a greater degree
of reliability than Bluetooth networks, be sure to take all
necessary precautions to ensure safety and prevent
malfunction. FUJIFILM Corporation and its affiliates do not
accept liability for damages resulting from unauthorized use.
■ Use only in the country in which the device was purchased�
This device conforms to regulations governing Bluetooth
devices in the country in which it was purchased. Observe all
location regulations when using the device. FUJIFILM
Corporation and its affiliates do not accept liability for problems
arising from use in other jurisdictions.
■ Wireless data (images) may be intercepted by third parties�
FUJIFILM Corporation and its affiliates are not responsible for
intercepted transmissions, or for unintended image uses.
■ Do not use the device in locations subject to magnetic fields,
static electricity, or radio interference�
Do not use the transmitter in the vicinity of microwave ovens or
in other locations subject to magnetic fields, static electricity, or
radio interference that may prevent reception of wireless
signals. Mutual interference may occur when the transmitter is
used in the vicinity of other wireless devices operating in the
2.4 GHz band.
■ The Bluetooth transmitter operates in the 2�4 GHz band� The
maximum radio-frequency power is 8�28 mW�
■ This device operates on the same frequency as commercial,
educational, and medical devices and wireless transmitters�
It also operates on the same frequency as licensed transmitters
and special unlicensed low-voltage transmitters used in radio-
frequency identification tracking systems for assembly lines and
in other similar applications.
■ To prevent interference with the above devices, observe the
following precautions�
Confirm that the radio-frequency identification transmitter is
not in operation before using this device. If you notice that this
device causes interference in low-voltage radio-frequency
identification tracing systems, contact a Fujifilm representative.
■ The following may be punishable by law:
– Disassembly or modification of this device.
– Removal of device certification labels.
15
For customers in the USA:
FCC ID : W2Z-03000010
FCC Statement
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1) this
device may not cause harmful interference, and (2) this device
must accept any interference received, including interference
that may cause undesired operation.
For more information, access the website below.
https://instax.com/square_link/en/spec.html
CAUTION
This device has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection
against harmful interference in a residential installation.
This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio
communications.
However, there is no guarantee that interference will not occur
in a particular installation.
If this equipment does cause harmful interference to radio or
television, which can be determined by turning the product off
and on, the user is encouraged to try to correct the interference
by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the product and receiver.
• Connect the product into an outlet on a circuit different from
that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for
help.
FCC CAUTION
Changes or modifications not expressly approved by Fujifilm
responsible for compliance could void the user's authority to
operate the equipment.
This transmitter must not be co-located or operated in
conjunction with any other antenna or transmitter.
Radiation Exposure Statement
This device meets the government's requirements for exposure
to radio waves. This device is designed and manufactured not to
exceed the emission limits for exposure to radio frequency (RF)
energy set by the Federal Communications Commission of the
U.S. Government.
The exposure standard employs a unit of measurement known
as the Specific Absorption Rate, or SAR. The SAR limit set by the
FCC is 1.6 W/kg. Tests for SAR are conducted using standard
operating positions accepted by the FCC with the device
transmitting at its highest certified power level in all tested
frequency bands.
Notes on the Grant
To comply with Part 15 of the FCC Rules, this product must be
used with a Fujifilm-specified USB Type-C cable.
Advertisement
Table of Contents
