Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Vidalux Hydro Plus Series
Summary of Contents for Vidalux Hydro Plus Series
- Page 1 Technical Support: 01524 489939...
- Page 2 VIDALUX CLEAR & BRIGHT WATER SOFTENER Guaranteed to get rid of limescale Live in a hard water area?? Limescale in the kettle and on bathroom fixtures?? Suffering from unknown adverse health effects from this polluted drinking water?? If you have a shower and any feature becomes blocked with limescale and stops working THIS IS...
- Page 3 Installation of the shower cabin is designed for a DIY installation. However any electric supply to the unit itself is required by law to be installed by a qualified trades person to ensure safety and quality. Failure to have the showers electric feed installed by qualified fitters will invalidate your product guarantee and be dangerous.
-
Page 5: You Will Need
Two flat static panels YOU WILL NEED This Shower requires 2 x 1 Metre Braided Hoses Not Supplied... - Page 6 You MUST register the product warranty within 90 days following delivery...
- Page 9 FITTING SEAT (OPTIONAL) If your product came with a seat you may choose to install this item. Before commencing full assembly of the product you will need to prepare and fi t the seat. You need to drill three holes for the fi xing bolts into the tower at your preferred height.
-
Page 10: Fitting The Control Panel
LEVELING AND FITTING THE TRAY Remove the protective fi lm covering the base. Connect the soil pipe, trap and any couplings to the fl exible waste under the tub. You may choose to fi t either a HEPV0 trap with the appropriate couplings or choose to fi t a McAlpine ST28M coupling to a McAlpine 28-NRV trap. - Page 11 REAR PANEL ASSEMBLY TIP: Only fi t each Locate the two rear, framed glass panels. screw loosely at The inside edge to go to the center control panel will be flat. The outside end to connect to the frame work will have a 'T' end and 90 first to allow degree return enough...
-
Page 12: Front Frame
FRONT FRAME Locate the two silver coloured upright frame sections and the two curved frame rail sections. You will need the 8 x LONGEST screws to join these sections together. The inside facing edges of the rails will be tapered, while the flat edge will meet the tray and the other will DO NOT FULLY TIGHTEN THE SCREWS - be closest to the bathroom ceiling. - Page 13 FITTING THE FRONT FRAME Place the front frame in to position and align the back panels and center column on the tray for fixing NOTE: A large bead of sealant MUST be run between the back panels and Front Frame work to provide an extra level of water protection.
- Page 14 INSTALLING THE FIXED SIDE GLASS PANELS Locate the two fi xed glass panels. These are diff erent from the doors as they do NOT have any holes pre- drilled. Now position this glass panel up to the frame pushing the long edge of the glass into the upright of the frame until FULLY bedded into the frame upright.
- Page 15 SHOWER CEILING Remove the protective fi lm from the roof/ceiling. If not already pre-fi tted, fi t the monsoon rain shower head into the centre of the roof. It is held in place with a retaining nut located on the outer/ upper face of the roof.
- Page 16 FITTING THE SHOWER DOOR WHEEL RUNNERS Locate the pack of 8 twin wheel shower door runners (cams). There are two diff erent types provided. (image based on top cam fi tting) To fi t each of the cams, fi rst select the appropriate cam for the position on the door: 4 x Push button/Quick release for the lower position on the doors.
-
Page 17: Fitting The Door Handles
FITTING THE DOOR HANDLES Each of the two shower doors requires a pair of chrome fi nished door handles to be fi tted. Each handle is comprised of several parts. Position the main handle part on the outside of a door ensuring the Chrome Washer and a Clear Washer are positioned also on the outside face over the thread. - Page 18 HAND SHOWER AND RISER You are now ready to assemble and connect the hand shower. The hand shower comprises of: Multi function hand shower ome nished riser bar Hand shower holster Chrome water hose Rear retaining nut Fitting screw The lower part of the riser bar has a threaded water connection.
- Page 19 GLASS SHELF Assemble the shelf fully before fi tting into the shower. Position the lower chrome rail over the holes in the glass on the underside of the shelf with the silver grommets positioned between the two. On the upper side of the glass, pass the bolt through a washer and through the hole in the glass and fasten into the end of the lower rail.
-
Page 20: Shower Valve
SHOWER VALVE The shower valve can be accessed from the rear of the shower and is located on the central tower. The valve is divided into three parts that are joined together. The uppermost part is the divertor. There are three connections able to be made here. - Page 21 SHOWER SEALS This shower comes with 2 fl apped shower seals that are in two diff erent lengths. LONG FLAPPED The longer fl apped seal fi t onto the trailing edges of the doors. The seals are not designed to touch the glass or each other, but when the doors are closed they will reduce the gap to a level that water is unlikely to escape.
-
Page 22: Water Connections
Water Connections This product requires a hot and cold water supply. Your Hot and Cold water supply pipes should ideally be fi nished about 1 meter above the fl oor centrally in the corner and fi nished with 15mm compression isolating valvea. - Page 26 The shower is supplied with a 12 volt transformer that needs connecting to the mains...
-
Page 27: Water Testing
Sealing the Shower OPTIONAL: Under normal use, the shower will return all water back into the tray. Should you choose, we recommend that you seal the shower internally with a good quality bathroom sealant to provide an extra level of water proofing. All sealant placed on the inside of the shower with a good quality 'Anti-Moulding' Sealant. -
Page 28: Final Testing
Final Testing Check and test that each outlet function (hand shower, body jets and monsoon) work as expected by rotating the DIVERTOR DIAL (top chrome dial). Check the ON/OFF dial enables the water to be fully on or off in the position indicated on the valve markings. -
Page 29: Valve Operation
Valve Operation There are 3 control dials inside your Shower Cabin. These dials control the output functions, water fl ow and temperature of your shower. The top dial can be turned to allow you to choose which output you wish to use: Body Jets, Overhead (Monsoon) Shower and Hand Shower. -
Page 30: Electronic Control Panel
Electronic Control Panel Your shower is fitted with an electronic control panel that allows you to operate the electronic features of your shower. From the control panel you can control the lights, Radio and Bluetooth audio. Power ON / OFF In standby mode this button is lit Red. -
Page 31: Bluetooth Pairing
Bluetooth Pairing Before you can start streaming Audio to your 5: After a small amount of time you should see shower you must fi rst establish a connection the device name of the shower appear “ SPROUT”. between the shower and the device that will Select this to complete the Pairing of the two stream the audio to the shower;... - Page 32 Thermostatic Cartridge Your shower is fi tted with a Thermostatic Cartridge. Should you need to remove or replace the cartridge for maintenance or replacement, follow the instructions below. Q: I am having to turn the dial round as far as it will go to the hottest setting and the water is only just warm.
- Page 33 With the Chrome dial removed you will see a plastic ring covering with the Thermostat underneath. Note down the position the ring is placed in. Pull the plastic ring (Temperature safety lock) towards you to remove. Keep this part safe You will now see the head of the Thermostat clearly visible.
- Page 34 01524 489939...
- Page 35 Shower Completion Form This form must be filled out by the plumber/installer and electrician (where applicable) in order to validate the warranty. You are required to register the warranty online at www.vidalux.co.uk PLEASE RETAIN THIS CERTIFICATE FOR FUTURE REFERENCE You MUST register the product warranty within 90 days following delivery Shower Details Model No.