Subscribe to Our Youtube Channel
Related Manuals for Grant-bio PHMP
Summary of Contents for Grant-bio PHMP
- Page 1 Thermo shaker PHMP/ PHMP-4 Operating instructions For versions V.5GW (PHMP) V.3GW (PHMP-4)
-
Page 2: Table Of Contents
Contents Safety..................3 General Information ..............5 Getting Started ................6 Operation of PHMP/PHMP-4 .............7 Specifications ................9 Guarantee and service............10 Version 3.01 - May 2015 Thermo shaker PHMP/PHMP-4 Page 2 Operating instructions... -
Page 3: Safety
Ensure that the switch and external power supply unit are easily accessible during use. Do not plug the unit into an ungrounded power socket, and do not use an ungrounded extension lead. Disconnect the unit from the electric circuit before moving. Thermo shaker PHMP/PHMP-4 Version 3.01 - May 2015 Operating instructions Page 3... - Page 4 Do not check the temperature by touch. Use a thermometer. BIOLOGICAL SAFETY It is the user's responsibility to carry out appropriate decontamination if hazardous material is spilt on or penetrates into the equipment. Version 3.01 - May 2015 Thermo shaker PHMP/PHMP-4 Page 4 Operating instructions...
-
Page 5: General Information
2. General Information The Thermo shaker PHMP / PHMP-4 is designed for shaking 1 to 4 standard 96-well plates in the thermal regulation mode. The Thermo shaker was designed using the multi-system principle, which allows using it as three independent devices: 1) incubator for lasting incubation of micro quantities (insect, plant cell cultures, etc.) in... -
Page 6: Getting Started
Remove protective film from the display; Plug the external power supply unit into the socket at the rear side of the PHMP and position the unit so that there is easy access to the power switch and the external power supply unit. -
Page 7: Operation Of Phmp/Phmp-4
4. Operation of PHMP / PHMP 00:00 1000 35.0 STOP 0000 35.0 Actual hr : min Thermo-Shaker Fig. 1 Control panel Connect the external power supply unit to a grounded power socket and set the power switch located on the rear panel of the unit to position I ("ON"). - Page 8 Place microplates on the platform and fix it with the special push-down clip by pressing it against the plate covers. PHMP-4: Unscrew the fixation screws. Place microplates on the platform and fix them by tightening the fixation screws. Caution! For model PHMP: Load only pairs of microplates for best fixing.
-
Page 9: Specifications
* Accurate within ±10%. Grant is committed to a continuous programme of improvement and reserves the right to alter design and specifications of the equipment without additional notice. Thermo shaker PHMP/PHMP-4 Version 3.01 - May 2015 Operating instructions Page 9... -
Page 10: Guarantee And Service
When used in laboratory conditions and according to these working instructions, this product is guaranteed for TWO YEARS against faulty materials or workmanship. For full Details of the Grant Bio Warranty policy please contact Grant Instruments. Service For service, return for repair to our Service Department in the UK or, in other countries, to our distributor. - Page 11 Thermo shaker PHMP/PHMP-4 Version 3.01 - May 2015 Operating instructions Page 11...
- Page 12 Thank you for reading this data sheet. For pricing or for further information, please contact us at our UK Office, using the details below. UK Office Keison Products, P.O. Box 2124, Chelmsford, Essex, CM1 3UP, England. Tel: +44 (0)1245 600560 Fax: +44 (0)1245 808399 Email: sales@keison.co.uk...
Need help?
Do you have a question about the PHMP and is the answer not in the manual?
Questions and answers