Turbo Timer - Philips VR1100/02X User Manual

When two programme overlap
The Program
PR CH START STOP
Review
1 12 08:00
screen will
2 25 11:00
3 03 09:00
appear with
4 45 03:00
a magenta
5
6
line blink-
7
8
ing on the
newly set
SELECT : 5∞
CONFIRM : OK
timer recor-
ding, while the other overlapped
programme blinking.
1 Press 5 or ∞ to move
the mage-
ONE TIME PROGRAM
PROGRAM
nta line
TV PROG +/-
among the
START+/-
STOP +/-
two over-
REC SPEED
lapping VPS/PDC
DATE +/-
programs.
2 Press OK/
ERASE : CLEAR
STATUS
CONFIRM : OK
to view
the detail information of the
program you want
to change.
3 Go to step 4 through 9 on page 30 for
Timer Recording to modify the
selected program. To cancel any
timer recording, press CLEAR.
• If you do not modify the overlapping
programs, the VCR will record the earlier
program completely. Only the remaining
part of the later program will be recorded.
• If the START time for the two programs
are the same, the lower program number
will be recorded.
Useful function for Timer
Recording: Auto Tape Speed
DATE
With this function activated, the VCR can
10:00 21/07
change the tape speed and record the
13:00 10/08
11:00W14/07
programme in LP mode if not enough
03:15W15/10
tape remains for recording in SP mode.
1 Press VCR.
2 Press MENU.
3 Press 5 or ∞ to select "VCR SET
UP", then press OK/STATUS.
4 Press 5 or ∞ to select "AUTO SP =
LP TIMER."
5 Press 4.
Each time you press the button, the
1
setting changes.
12
08:00
ON:
10:00
SP
Select this to allow the VCR to
ON
change the tape speed from SP to
21/07/00
FRIDAY
LP when there is not enough tape
length remaining.
END : TIMER
OFF:
Select this not to allow the VCR to
change the tape speed.
6 Press MENU to exit from the menu
operations.
Notes:
• The Auto SP = LP Timer feature is not
available during OTR (One Touch
Recording) and the feature will not work
properly with any tapes longer than E-
180 or with some tapes of shorter lengths.
• If you have programmed the recorder to
timer-record 2 or more programmes, the
second programme and those hereafter
may not fit on the tape if you set "AUTO
SP = LP TIMER" to "ON". In this case,
make sure the mode is not engaged, then
set the tape speed manually during timer
programming.
• In order to ensure that the recording fits on
the tape, this feature may leave a short non-
recorded section at the end of the tape.
• There may be some picture noise and sound
disturbance at the point on the tape where
the recorder switches from SP to LP mode.
• If you perform timer recording with both
VPS/PDC and the Auto SP = LP Timer
activated, and the programme goes
beyond its originally scheduled length,
there may be times when the programme
cannot be recorded in its entirety.
— 31 —

Turbo Timer

This function allows you to set the
timer recording program without going
through the regular set up with the on
screen. The extent of programming is
24 hours from the current time.
1 Insert a tape into the VCR and press
the "TURBO TIMER" button on the
remote control. Current time will
appear on the display panel.
VCR
2 To change the START time, press the
5 or ∞ ( if you press and hold the
button, the time changes in
30-minute increments) then press
OK/STATUS.
VCR
3 To change the STOP time, press the
5 or ∞ ( if you press and hold a
button, the time changes in
30-minute increments) then press
OK/STATUS.
VCR
4 To change the CHANNEL position,
press the 5 or ∞, then press
OK/STATUS.
VCR
5 The data input will be memorized
and the Turbo Timer mode will be
finished so that normal display
appears.
6 Turn off the VCR.
Notes:
• To exit Turbo Timer mode at any step,
press the TURBO TIMER button.
• If "Err" appears on the display panel,
all eight programs have been set and
Turbo Timer will not proceed. To
remove the error message, press the
TURBO TIMER button again.
• Settings of Turbo Timer will appear
on the display panel only and not on
the screen.
• Programs Overlap Warning does not
function with Turbo Timer.
• DAILY or WEEKLY programming
are not available on Turbo Timer.
• Tape speed can be selected anytime
during steps 2 through 4.
SP
SP
SP
SP