Advertisement
Quick Links
BEFORE YOU BEGIN
BEFORE YOU BEGIN
·
Before you install your shower door, please read
these instructions carefully to familiarize yourself
with the required tools, materials, and installation
sequences. Follow the sections that pertain to your
particular installation. This will help you avoid costly
mistakes. In addition to proper installation, read all
operating and safety instructions.
·
All information is based on the latest product
information available at the time of publication.
Kohler China Ltd. reserves the right to make
changes in product characteristics, packaging, or
availability at any time without notice.
·
These instructions contain important care, cleaning,
and warranty information-
instructions for the consumer.
·
Make sure that the bath and the finished wall
material are completely and correctly installed prior
to installing your shower door. Prepare waterproof
layer to wall and floor of the showering area. It is not
allowed for any presence of electric switches and
sockets. Make sure the floor drain runs smoothly.
·
Before starting the door installation, lay out and
identify all the parts. Use the exploded view
illustrated on page 3 for reference.
·
For the installation method of customized shower
with different dimensions, please refer to this
instructions.
CAUTION: Risk of injury or product damage.
Tempered glass cannot be cut, drilled or
knocked by hard object. Make sure corner area
of the glass refraining from knocking so as to
cause personal injury due to broken glass.
Please install this door on Kohler
ATTENTION:
receptors or curbs (Not included). If the curb is not
Kohler-branded, please note its top width should be
more than 80mm.
IMPORTANT:
The shower door requires a flat vertical
finished wall. The squareness of the wall is
recommended no more than 3 mm/m. KOHLER
Company won't take responsibility of the installation
quality.
1227978-T01-A
please leave these
·
·
·
·
·
·
)
13-1
-1-
PURIST UPGRADE
INSTALLATION INSTRUCTIONS
L
10mm
L SHPE, SEALED, 10mm C
3
80mm
3mm/m
528437
Copyright Kohler China Ltd., 2014
K-99172T
(
, 2014
Advertisement
Related Manuals for Kohler PURIST UPGRADE
Summary of Contents for Kohler PURIST UPGRADE
- Page 1 · · All information is based on the latest product information available at the time of publication. Kohler China Ltd. reserves the right to make changes in product characteristics, packaging, or availability at any time without notice. · ·...
-
Page 2: Parts Identification
ROUGHING-IN Unit: mm K-99172T 900-1600 250-1100 2000-2500 PARTS IDENTIFICATION PARTS IDENTIFICATION Glass Clamp Top Frame, Return Side Steel Piece Assy Top Frame Pressing Block Transom Door Glass Purist Transom Pivot Assy, 1D1P Purist Handle Assy Purist Transom Pivot Assy, 1D2P Wall Channel Purist Top Hinge Assy Hingelite Panel... -
Page 3: Installation Requirements
INSTALLATION REQUIREMENTS INSTALLATION REQUIREMENTS Tools Required · · Phillips Screwdriver · · Pencil · · Caulk Gun · · Measuring Tape · · Safety Glasses · Center Punch · · Hammer · · Knife · · Masonry Drill & 6mm Drilll Bit ·... - Page 4 Tray must be level in all planes or door will not install properly. Common water divider used by customer This instruction is based on simple water divider of Kohler brand, which is installed with 20mm offset. You may choose and adjust its width as desired. 20mm STEP Pre-install seals onto the wall channel and then fix it.
- Page 5 Fix the wall channel on the other side by following the Connect and combine top frame. same steps. STEP STEP Make sure the ceiling is firm enough. Trace the line Insert the return panel into the wall channel. and drill holes. STEP STEP 1227978-T01-A...
- Page 6 Insert the top frame along the return panel. Fix the top frame onto the ceiling. STEP STEP Insert the hingelite panel into the wall channel. Fix the bottom hinge onto the side panel. STEP STEP 1227978-T01-A...
- Page 7 Adjust the two side panels to make them about Tighten the screws of the wall channels and clamp the 662mm apart. side panels. 662mm <8 STEP STEP Fix the upper hinge onto the door glass. Remove the upper and bottom hinge covers and the clamp plates.
- Page 8 Lift the door glass and insert into the bottom hinge. Fix the clamp plate into the bottom hinge to tightly clip the glass. Pay attention to the direction of the rubber gasket. IMPORTANT: Ensure the door is fully supported at all times. STEP STEP Fix the upper clamp plate.
- Page 9 Install door handle. Fix the transom assembly to the side panel and wall channel. Do not tighten the screws. STEP STEP Fix the transom to the assembly, adjust the gaps on Fix door seal and side seal. each side and then tighten the screws. Inward-opening door Inside Outside...
- Page 10 Fix bottom seal. Insert side seal between side panel and top frame. Insert decorative seal into top frame. Insert seals into two sides of the transom panels. STEP STEP Drill a 3.3 hole. Fix the bottom hinge and side panel Assemble the L shape connector and fix the pressing block to the bottom panel.
- Page 11 Fix upper and bottom hinge covers. Tighten the upper and bottom hinge covers by tightening the screw. STEP STEP Fix decorative cover of the transom assembly. Fix other decorative covers. STEP STEP 1227978-T01-A -11-...
- Page 12 Apply a thin layer of silicone sealant on the bottom Do not use the enclosure for at least 24 hours. frame. 24hrs STEP STEP 1227978-T01-A -12-...