Advertisement
Quick Links
·
Before you install your shower door, please read
these instructions carefully to familiarize yourself
with the required tools, materials, and installation
sequences. Follow the sections that pertain to your
particular installation. This will help you avoid costly
mistakes. In addition to proper installation, read all
operating and safety instructions.
·
All information is based on the latest product
information available at the time of publication.
Kohler China Ltd. reserves the right to make
changes in product characteristics, packaging, or
availability at any time without notice.
·
These instructions contain important care, cleaning,
and warranty information-
instructions for the consumer.
·
Make sure that the bath and the finished wall
material are completely and correctly installed prior
to installing your shower door. Prepare waterproof
layer to wall and floor of the showering area. It is not
allowed for any presence of electric switches and
sockets. Make sure the floor drain runs smoothly.
·
Before starting the door installation, lay out and
identify all the parts. Use the exploded view
illustrated on page 2 for reference.
·
For the installation method of customized shower
with different dimensions, please refer to this
instructions.
CAUTION: Risk of injury or product damage.
Tempered glass cannot be cut, drilled or
knocked by hard object. Make sure corner area
of the glass refraining from knocking so as to
cause personal injury due to broken glass.
ATTENTION:
Please install this door on Kohler
receptors or curbs (Not included). If the curb is not
Kohler-branded, please note its top width should fall
above 80mm.
IMPORTANT:
The shower door requires a flat vertical
finished wall. The squareness of the wall is
recommended no more than 3 mm/m. KOHLER
Company won't take responsibility of the installation
quality.
1220638-T01-A
please leave these
·
·
·
·
·
·
3mm/m
13-1
-1-
PURIST UPGRADE
INSTALLATION INSTRUCTIONS
SCREEN 1D2P, SHP, 10mm
2
80mm
528437
Copyright Kohler China Ltd., 2014
10mm
K-99168T
, 2014
Advertisement
Related Manuals for Kohler PURIST UPGRADE K-99168T
Summary of Contents for Kohler PURIST UPGRADE K-99168T
- Page 1 · · All information is based on the latest product information available at the time of publication. Kohler China Ltd. reserves the right to make changes in product characteristics, packaging, or availability at any time without notice. · ·...
-
Page 2: Parts Identification
ROUGHING-IN Unit: mm K-99168T 1200-2200 1850-2000 PARTS IDENTIFICATION PARTS IDENTIFICATION Glass Clamp Purist Bracket Assy Side Seal Door Glass Pressing Block Purist Top Hinge Assy Side Panel Wall Channel Purist Bottom Hinge Assy Purist Handle Assy Hingelite Panel Cover 2.5mm Allen Key Bottom Frame 2mm Allen Key 2.5mm... -
Page 3: Installation
INSTALLATION Pre-install the bottom rail with seals and Pre-install seals onto the wall channel and then fix it. then put it onto the threshold. Wall channels MUST plumb. Align STEP STEP Insert the hingelite panel into the wall channel. Fix the wall channel and glass on the other side by following the same steps. - Page 4 Fix the bottom hinge onto the side Adjust the two side panels to make them about 662mm apart. panel. 662mm Note: When adjusting the side panels, please clamp as much of the hingelite panel as possible. <8 STEP STEP Tighten the screws of the wall channels and clamp Fix the upper hinge onto the door glass.
- Page 5 Remove the upper and bottom hinge covers and the Lift the door glass and insert into the bottom hinge. clamp plates. STEP STEP Fix the clamp plate into the bottom hinge to tightly clip Fix the upper clamp plate. Adjust the rollers to make the glass.
- Page 6 If 90 degree is not suitable, please turn the set screw Install door handle. slightly and try again. STEP STEP Fix door seal and side seal. Fix bottom seal. Inward-opening door Inside Outside Outward-opening door Inside Outside STEP STEP 1220638-T01-A...
- Page 7 Drill a 3.3 hole. Fix the bottom hinge and side panel Adjust to a proper angle and install the handle. block to the bottom panel. STEP STEP Fix upper and bottom hinge covers. Tighten the upper and bottom hinge covers by tightening the screw.
- Page 8 Fix other decorative covers. Apply a thin layer of silicone seal on the bottom frame STEP STEP Do not use the enclosure for at least 24 hours. 24hrs STEP 1220638-T01-A...