Advertisement
BEFORE YOU BEGIN
BEFORE YOU BEGIN
·
Before you install your shower door, please read
these instructions carefully to familiarize yourself
with the required tools, materials, and installation
sequences. Follow the sections that pertain to your
particular installation. This will help you avoid costly
mistakes. In addition to proper installation, read all
operating and safety instructions.
·
All information is based on the latest product
information available at the time of publication.
Kohler China Ltd. reserves the right to make
changes in product characteristics, packaging, or
availability at any time without notice.
·
These instructions contain important care, cleaning,
and warranty information-
instructions for the consumer.
·
Make sure that the bath and the finished wall
material are completely and correctly installed prior
to installing your shower door. Prepare waterproof
layer to wall and floor of the showering area. It is not
allowed for any presence of electric switches and
sockets. Make sure the floor drain runs smoothly.
·
Before starting the door installation, lay out and
identify all the parts. Use the exploded view
illustrated on page 3 for reference.
·
For the installation method of customized shower
with different dimensions, please refer to this
instructions.
CAUTION: Risk of injury or product damage.
Tempered glass cannot be cut, drilled or
knocked by hard object. Make sure corner area
of the glass refraining from knocking so as to
cause personal injury due to broken glass.
Please install this door on Kohler
ATTENTION:
receptors or curbs (Not included). If the curb is not
Kohler-branded, please note its top width should be
more than 80mm.
IMPORTANT:
The shower door requires a flat vertical
finished wall. The squareness of the wall is
recommended no more than 3 mm/m. KOHLER
Company won't take responsibility of the installation
quality.
1227973-T01-A
please leave these
·
·
·
·
·
·
)
13-1
-1-
PURIST UPGRADE
INSTALLATION INSTRUCTIONS
10mm,
SCREEN 1D2P, SEALED, 10mm C
3
80mm
3mm/m
528437
Copyright Kohler China Ltd., 2014
K-99171T
(
, 2014
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Kohler Purist K-99171T
Summary of Contents for Kohler Purist K-99171T
- Page 1 · · All information is based on the latest product information available at the time of publication. Kohler China Ltd. reserves the right to make changes in product characteristics, packaging, or availability at any time without notice. · ·...
-
Page 2: Parts Identification
ROUGHING-IN Unit: mm K-99171T 1200-2200 2000-2500 PARTS IDENTIFICATION PARTS IDENTIFICATION Glass Clamp Top Frame Purist Transom Pivot Assy, 1D2P Transom Pressing Block Side Seal Door Glass Side Panel Purist Top Hinge Assy Wall Channel Purist Bottom Hinge Assy Purist Handle Assy Cover Hingelite Panel 2.5mm Allen Key... -
Page 3: Installation Requirements
INSTALLATION REQUIREMENTS INSTALLATION REQUIREMENTS Tools Required · · Phillips Screwdriver · · Pencil · · Caulk Gun · · Measuring Tape · · Safety Glasses · Center Punch · · Hammer · · Knife · · Masonry Drill & 6mm Drilll Bit ·... - Page 4 Fix the wall channel on the other side by following the Make sure the ceiling is firm enough and then fix the same steps. top frame onto the ceiling. STEP STEP Insert the hingelite panel into the wall channel. Fix the glass on the other side by following the same steps.
- Page 5 Fix the bottom hinge onto the side panel. Adjust the two side panels to make them about 662mm apart. 662mm Note: When adjusting the side panels, please clamp as much of the hingelite panel as possible. <8 STEP STEP Tighten the screws of the wall channels and clamp the Fix the upper hinge onto the door glass.
- Page 6 Remove the upper and bottom hinge covers and the Lift the door glass and insert into the bottom hinge. clamp plates. IMPORTANT: Ensure the door is fully supported at all times. STEP STEP Fix the clamp plate into the bottom hinge to tightly clip Fix the upper clamp plate.
- Page 7 If 90 degree is not suitable, please turn the set screw Install door handle. slightly and try again. STEP STEP Fix the transom assembly to the side panel. Do not Fix the transom to the assembly, adjust the gaps on tighten the screws.
- Page 8 Fix door seal and side seal. Fix bottom seal. Inward-opening door Inside Outside Outward-opening door Inside Outside STEP STEP Insert side seal between side panel and top frame. Drill a 3.3 hole. Fix the bottom hinge and side panel block to the bottom panel. Insert decorative seal into top frame.
- Page 9 Fix upper and bottom hinge covers. Tighten the upper and bottom hinge covers by tightening the screw. STEP STEP Fix decorative cover of the transom assembly. Fix other decorative covers. STEP STEP 1227973-T01-A...
- Page 10 Apply a thin layer of silicone seal on the bottom frame Do not use the enclosure for at least 24 hours. 24hrs STEP STEP 1227973-T01-A -10-...
Need help?
Do you have a question about the Purist K-99171T and is the answer not in the manual?
Questions and answers