Advertisement
Quick Links
Instructions - Parts List
Dispenser Bar
Used for low volume dispense of petroleum-based lubricants. For professional use only.
Model 220107, Series A
900 psi (6.2 MPa, 62 bar) Maximum Working Pressure
Model 220107, Series A, with Meter Kit 238706
500 psi (3.4 MPa, 34 bar) Maximum Working Pressure
Important Safety Instructions
Read all warnings and instructions in this
manual. Save these instructions.
307742N
Model 220107
Without Meter Kit
EN
Advertisement
Related Manuals for Graco 220107 A Series
Summary of Contents for Graco 220107 A Series
- Page 1 Instructions - Parts List Dispenser Bar 307742N Used for low volume dispense of petroleum-based lubricants. For professional use only. Model 220107, Series A 900 psi (6.2 MPa, 62 bar) Maximum Working Pressure Model 220107, Series A, with Meter Kit 238706 500 psi (3.4 MPa, 34 bar) Maximum Working Pressure Important Safety Instructions Read all warnings and instructions in this...
-
Page 2: Table Of Contents
Dimensions ....... 9 Graco Standard Warranty ....10... -
Page 3: Warnings
Warnings Warnings The following warnings are for the setup, use, grounding, maintenance, and repair of this equipment. The exclama- tion point symbol alerts you to a general warning and the hazard symbols refer to procedure-specific risks. When these symbols appear in the body of this manual, refer back to these Warnings. Product-specific hazard symbols and warnings not covered in this section may appear throughout the body of this manual where applicable. -
Page 4: Installation
Installation Installation NOTE: Be sure to install a fluid shutoff valve, located 7. Secure the manifold to the front panel with two lock- close to the dispenser bar, to shut off fluid to the dis- washers (2) and screws (5). penser when servicing. -
Page 5: Service
Service Service Dispensing Valve Service and To replace the valve stem (110), spring (112) or pack- ings (105): Adjustment a. Drive the pin (113) out of the handle (103) with Refer to Parts Drawing on page 7 for the following a 1/8 in. -
Page 6: Parts
Parts Parts DETAIL Dispenser Securing Sides of Two Dispensers Oil Dispenser Model 220107, Series A Part No. Description Qty. Part No. Description Qty. 181317 MANIFOLD, dispenser 100015 NUT, hex, 1/4-20 unc-2A 181319 STAINER, pan 100016 LOCKWASHER, 1/4 in. 16D537 PAN, drain 102521 BUTTON, plug, 7/8 in. - Page 7 Parts Ref. No. 16 Model 220110 Dispensing Valve Part No. Description Qty. 108789 KNOB, handle 154773 HANDLE 154891 NUT, adjusting 105* 154594 PACKING, o-ring, nitrile rubber 166779 NOZZLE, valve 107* 156312 SEAL, valve, nitrile rubber 156311 SCREW, valve 109* 558690 O-RING 154781 STEM, valve 179932 HOUSING, valve 105*...
-
Page 8: Accessories
Accessories Accessories Solenoid Valve and Ready Light Kit 218588 Dispenser Meter Kit 239706 To add an electronic gallon/quart/ pint/liter totalizing Air operated solenoid valve opens and closes to control meter. fluid flow to the dispensing station. Light signals the operator when the order is ready to dispense. See man- ual 307696. -
Page 9: Dimensions
Dimensions Dimensions Inches (mm) Mounting Holes (25.4) 22.6 (574) 0.44 (11.2) dia. (101.6) 15.18 18.3 (385.6) (464.82) (38.1) 13.25 (336.5) Technical Data Dispenser Bar Metric Maximum fluid working pressure Dispenser Only 900 psi 6.2 MPa, 62 bar Dispenser with meter kit 500 psi 3.4 MPa, 34 bar Fluid inlet size... -
Page 10: Graco Standard Warranty
With the exception of any special, extended, or limited warranty published by Graco, Graco will, for a period of twelve months from the date of sale, repair or replace any part of the equipment determined by Graco to be defective.