Related Manuals for H3C WA2610i-GN
Summary of Contents for H3C WA2610i-GN
- Page 1 H3C WA2610i-GN Access Point Installation Guide Hangzhou H3C Technologies Co., Ltd. http://www.h3c.com Document version: APW102-20130320...
- Page 2 Copyright © 2011-2013, Hangzhou H3C Technologies Co., Ltd. and its licensors All rights reserved No part of this manual may be reproduced or transmitted in any form or by any means without prior written consent of Hangzhou H3C Technologies Co., Ltd.
- Page 3 Preface The H3C WA2610i-GN AP Installation Guide describes the hardware specifications, preparations before installation, installation procedure, cabling and grounding, and login procedure of the WA2610i-GN AP. This preface includes: Audience • Conventions • Obtaining documentation • Technical support • •...
- Page 4 Obtaining documentation You can access the most up-to-date H3C product documentation on the World Wide Web at http://www.h3c.com. Click the links on the top navigation bar to obtain different categories of product documentation: [Technical Support & Documents > Technical Documents] –...
-
Page 5: Table Of Contents
Contents Product overview ·························································································································································· 1 Preparing for installation ············································································································································· 3 Safety recommendations ·················································································································································· 3 Accessories provided with the AP ··································································································································· 3 Installing the AP ···························································································································································· 4 Check before installation ·················································································································································· 4 Determining the installation position ······························································································································· 5 ... -
Page 6: Product Overview
The H3C WA2610i-GN Access Point has integrated antennas, and also supports external antennas. The WA2610i-GN can serve as a fit AP to cooperate with wireless switches or access controllers to provide wireless access for WLAN users. All configuration tasks are configured on the wireless switches or access controllers. - Page 7 Table 1 Basic configuration Dimensions (H × W × D) Weight Max. power Enclosure Protocol Power supply 328 g 160 × 160 × 50 mm (6.30 802.11b/g/ Local power (11.57 12.95 W Plastic × 6.30 × 1.97 in) supply + 802.3af...
-
Page 8: Preparing For Installation
Safety recommendations WARNING! Only qualified personnel can install and remove a WA2610i-GN and its accessories. You must read all safety instructions supplied with the access points before installation and operation. To avoid possible bodily injury and equipment damage, read the following safety recommendations before you install a WA2610i-GN. -
Page 9: Installing The Ap
Installing the AP CAUTION: The WA2610i-GN is usually installed on a high position, such as a wall or ceiling, so the maintenance personnel cannot log in from the console port to maintain and debug the AP. H3C recommends that you log in to the AP through the console port to perform remote login (Telnet or web login) configuration, or log in through Telnet or web by using the default login information before you install the AP. -
Page 10: Determining The Installation Position
Mounting the AP on a table WARNING! Do not place the WA2610i-GN on any metal surface. Place it on a place where there are no obstacles and good signal strength is available. To mount the AP on a table, attach the rubber feet supplied with the AP to the rear of the AP. -
Page 11: Mounting The Ap On A Wall
Place the AP on the table with the rubber feet facing downwards. Figure 5 Mounting the AP on a table Mounting the AP on a wall To mount the AP on a wall, you need a wall-mounting bracket and wall anchor kit. Figure 6 Screw hole locations and sizes (in mm) (1) Hook (2) Mounting hole... - Page 12 Figure 7 Drill holes on the wall 40 mm (1.57 in) 86 mm (3.39 in) Insert a wall anchor into each mounting hole, and tap the wall anchor with a rubber hammer until it is all flush with the wall surface. Figure 8 Fix the anchor to the wall Align the holes in the wall-mounting bracket with the anchors and insert screws through the installation holes into the wall anchors.
- Page 13 Figure 9 Install the wall-mounting bracket (1) Wall anchor (2) Wall-mounting bracket (3) Hook (4) Clip (5) Screw Connect the AP to the network by using an Ethernet cable. Align the mounting keyhole on the rear of the AP over the hook on the wall-mounting bracket. Mount the AP on the hook on the wall-mounting bracket.
-
Page 14: Mounting The Ap On A Ceiling
Figure 10 Fix the AP onto the wall-mounting bracket Mounting the AP on a ceiling NOTE: The ceiling tiles must be less than 18 mm (0.71 in) thick, and the ceiling can bear a weight of at least 5 • kg (1 1.02 lb). -
Page 15: Connecting The Power Supply
(5) Hex-head bolt (6) Hook CAUTION: Check that the AP is secured to the mounting bracket to avoid falloff. Connecting the power supply The WA2610i-GN can be powered through PoE or a power adaptor. You can select either method as needed. -
Page 16: Check Before Power-On
+48V at 0.52 A The WA2610i-GN supports both AC and DC power adapters. You can connect the power port of the AP to the power source through a power adapter to supply power to the AP. Figure 13 Local power supply connection... -
Page 17: Poe Power Supply
PoE power supply CAUTION: When you apply 802.3af PoE power supply, connect one end of the network cable to the network port • on the AP, and the other end to an Ethernet port on a PoE-capable device (for example, a PoE-capable Ethernet switch). -
Page 18: Checking The Network Connection For The Fat Ap
-------------------------------------------------------------------------------- AP Name State Model Serial-ID -------------------------------------------------------------------------------- WA2610i-GN 219801A0CLC118000435 -------------------------------------------------------------------------------- <AC> Checking the network connection for the fat AP When the AP operates as a fat AP, use the ping command to ping the uplink network. If the network can... -
Page 19: Logging In To The Fat Ap
AP. When the WA2610i-GN operates as a fat AP, you can log in to the AP through the console port, or through Telnet or web to configure the AP, but you must obtain the IP address of the AP first. -
Page 20: Setting Terminal Parameters
Figure 15 Connect the console cable Power on the AP. The AP’s startup information will be displayed. Setting terminal parameters To set terminal parameters, for example, on a Windows XP HyperTerminal: Select Start > All Programs > Accessories > Communications > HyperTerminal. The Connection Description dialog box appears. - Page 21 Figure 17 Set the serial port used by the HyperTerminal connection Set Bits per second to 9600, Data bits to 8, Parity to None, Stop bits to 1, and Flow control to None, and click OK. Figure 18 Set the serial port parameters NOTE: To restore the default settings, click Restore Defaults.
-
Page 22: Logging In Through The Console Port
If the default IP address is changed, contact the administrator to get the new IP address, or use the display vlan 1 command to view the IP address after logging in to the AP from the console port. NOTE: H3C WA Series Access Points For more information about Telnet or web login configuration, see Configuration Guides... -
Page 23: Appendix Leds And Ports
Appendix LEDs and ports LEDs Table 3 describes the LEDs provided by the WA2610i-GN. Table 3 LED description Mark Color Status Description The AP is booting. NOTE: Flashing at 1 Hz Green When the AP operates as a fit AP, it is always in this state before it is registered to an AC. - Page 24 A power supply port • NOTE: The WA2610i-GN also provides a reset button. Figure 20 WA2610i-GN ports (1) Ethernet Port (2) Ethernet Cable (3) PoE switch (4) 10/100/1000 Mbps copper Ethernet port (5) Local power port (6) 2.4G antenna port 1...
-
Page 25: Index
Index C L M P S Mounting the AP on a ceiling,9 Mounting the AP on a table,5 Check after power-on,12 Mounting the AP on a wall,6 Check before power-on,1 1 Checking the network connection for the fat AP,13 Checking the network connection for the fit AP,12 PoE power supply,12...