Related Manuals for Central Machinery 42289
Summary of Contents for Central Machinery 42289
- Page 1 Brought to You by Augusta Flint 34” RADIAL BENCH DRILL PRESS 42289 ASSEMBLY & OPERATING INSTRUCTIONS (Stand Not Shown) 2000...
- Page 2 SAVE THE RECEIPT, WARRANTY AND THESE INSTRUCTIONS. It is important that you read the entire manual to become familiar with the unit BEFORE you begin assembly. Technical Specifications Tool Name: 34" Radial Bench Drill Press Item Number: 42289 Motor: 120V/60HZ, 3 Amps, Single Speed, 1720 RPM Radial Travel: 12" Spindle RPM:...
- Page 3 The plugs have different shapes to prevent this. This tool has a three-prong plug. The third (round) prong is the ground. Cutting off the ground will result in a safety hazard and void the warranty. #42289 Page 3...
- Page 4 Make certain that the holes line up with the holes in the Legs. Insert two (2) Bolts (part #23C) through each Leg (#24C) and through the Side Panel (#21C) on both sides. Repeat for the second set of Legs. #42289 Page 4...
- Page 5 Step 3. Tighten it with the Hex wrench used in Step 3 . Note: Only tighten the Screw (#11C) enough to keep the Collar in place. Over tightening the Screw may result in breaking of the Column Collar (#19C). #42289 Page 5...
- Page 6 Feed Rods (part #35B) firmly into the Hub (#36B). Screw each of the three Feed Knobs (part #34B) onto the Feed Rods (#35B) - see Figure 3. Depth Lock Screw (38B) Hub (36B) Depth Ring Stop (37B) Feed Rod (35B) Feed Knob (34B) Figure 3 - Feed Rod Assembly #42289 Page 6...
- Page 7 To adjust the Angle, loosen the right Clamping Lever (#30B). Then pull out the Guide Pin (part #16B) and turn it 90 degrees so that it’s cross pin rests on top of the outlet - see Figure 5. Figure 5 - Guide Pin #42289 Page 7...
- Page 8 With the Depth Lock Screw loose, set the Scale on the Depth Stop Top Ring (part #37B) to the depth of the hole desired. Step 2) Tighten the Depth Lock Screw (#38B) until secure. The Drill is now set to drill holes to the desired depth. #42289 Page 8...
- Page 9 Generally, the SMALLER THE DRILL BIT the GREATER THE REQUIRED RPM. In soft material, the speed should be higher than for hard metals. As a general guide, the drill speed for a given drill bit size is listed in the chart on the next page. #42289 Page 9...
- Page 10 Make certain that this piece, when removed, is stored in a safe place. Insert the “snap-in” piece into the switch. To turn the machine ON, put your finger under the switch lever and push up. To turn the machine OFF, pull the lever down. #42289 Page 10...
- Page 11 Child-proof the machine and work area. Make sure to use padlocks, master switches and remove the Lock Switch’s “snap-in” piece. IF THERE IS ANY QUESTION ABOUT A CONDITION BEING SAFE OR UNSAFE DO NOT OPERATE THE TOOL Troubleshooting #42289 Page 11...
-
Page 12: Unpack And Check Contents
Motor Pulley Tube Quill Screw M6 x 10 Chuck Key Belt Guard Chuck Form Washer Arbor Spacer Key Drift Parts List - #42289-B Part # Description Part # Description Lock Switch Motor Mount Switch Cover Motor Screw Pan Head Nut M8... -
Page 13: Please Read The Following Carefully
Brought to You by Augusta Flint Parts List - #42289-C Part # Description Part # Description Column Column Collar Rack Table Column Support Side Panel Hex Bolt M8 x 20 Nut M6 Base Bolt M6 x 16 Table Support Crank... - Page 14 Brought to You by Augusta Flint Assembly Diagram - #42289-A All parts in this diagram correspond to parts listed with an “A” suffix. #42289 Page 14...
- Page 15 Brought to You by Augusta Flint Assembly Diagram - #42289-B All parts in this diagram correspond to parts listed with a “B” suffix. #42289 Page 15...
- Page 16 Brought to You by Augusta Flint Assembly Diagram - #42289-C All parts in this diagram correspond to parts listed with an “C” suffix. Wiring Diagram #42289 Page 16...