Advertisement
Available languages
Available languages
DMX-controlled operation
Building a serial DMX-chain:
Connect the DMX-output of the first fixture in the DMX-chain with the DMX-input of the next fixture. Always
connect one output with the input of the next fixture until all fixtures are connected.
Caution: At the last fixture, the DMX-cable has to be terminated with a terminator. Solder a 120
between Signal (–) and Signal (+) into a 3-pin XLR-plug and plug it in the DMX-output of the last fixture.
Addressing
The Control Board allows you to assign the DMX starting address, which is defined as the first channel from
which the PCC-250 will respond to the controller.
Please, be sure that you don't have any overlapping channels in order to control each PCC-250 correctly
and independently from any other fixture on the DMX-chain.
If several PCC-250 are addressed similarly, they will work synchronically.
Press the Up/Down-buttons for setting the desired starting address. Now you can start operating the PCC-
250 via your lighting controller.
DMX-protocol
Channel 1
Colour-wheel
Channel 2
Effect-wheel
Channel 3
Zoom
In order to call up the different features, you first have to ignite the lamp (control channel 6, DMX-value 64-
79) and open the shutter (control channel 4, DMX-value 224-255). The dimmer is only active if channel 4 is
set to 32-63.
Technical specifications
Power supply:
Power consumption:
DMX-control-channels:
DMX-512-connection:
Flash-rate:
Colour-wheel:
Dimensions (LxWxH):
Weight:
Maximum ambient temperature t
Maximum housing temperature t
Min.distance from flammable surfaces:
Min.distance to lighted object:
Fuse:
Accessory:
OMNILUX OSD 90V/250W GY-9.5 2000h 6700K
OSRAM HSD 250/60 90V/250W GY-9.5 2000h
PHILIPS MSD250 90V/250W GY-9.5 2000h
GE CSD250/2 95V/250W GY-9.5 2000h 8500K
OMNILUX OSD 250/2 94V/250W 2000h 8000K
OSRAM HSD250/78 90/250W GY9.5 3000h 7800K
PHILIPS MSD250/2 90V/250W GY-9.5 2000h
SYLVANIA BA250/2 SE D 90V/250W GY-9.5
OSRAM HSD250/80 90/250W GY9.5 3000h 8000K
FUTURELIGHT FS-1 for PCC-250/500
Barndoors for PCC-250/PCC-500
FUTURELIGHT EX-6/32 controller
FUTURELIGHT EX-8/32 controller
FUTURELIGHT CP-240 controller
FUTURELIGHT CP-256 controller 16bit
FUTURELIGHT CP-256/32 controller 16bit
FUTURELIGHT CP-528 controller 16bit
Wizard-512 USB DMX-Software + Interface
Wizard-1024 USB DMX-Software + Interface
FUTURELIGHT DES-3 DMX-terminator 3-pin
Please note: Every information is subject to change without prior notice. 02.08.2005 ©
Channel 4
Channel 5
Channel 6
230 V AC, 50 Hz ~
440 W
6
3-pin XLR
13 Hz
4 dichroic filters and white
325 x 435 x 350 mm
13 kg
:
45° C
a
(steady state):
80° C
B
0.5 m
0.5 m
T 4 A, 250 V
No. 89106005
No. 89106010
No. 89106015
No. 89106100
No. 89106105
No. 89106110
No. 89106115
No. 89106120
No. 89106210
No. 51840956
No. 51840955
No. 51834046
No. 51834047
No. 51834265
No. 51834285
No. 51834286
No. 51834315
No. 51860102
No. 51860110
No. 51834001
Ω
Shutter, Strobe
Dimmer
Lamp, reset, programs
resistor
Advertisement
