Page 2
User Guide for FibeAir® IP-20 All-Outdoor Products, CeraOS 10.5 Notice This document contains information that is proprietary to Ceragon Networks Ltd. No part of this publication may be reproduced, modified, or distributed without prior written authorization of Ceragon Networks Ltd. This document is provided as is, without warranty of any kind.
2.10.3 Entering the Activation Key ....................... 79 2.10.4 Activating Demo Mode ......................79 2.10.5 Activation Key Reclaim ....................... 79 2.10.6 Displaying a List of Activation-Key-Enabled Features ..............81 2.11 Setting the Time and Date (Optional) ..................82 Page 3 of 825 Ceragon Proprietary and Confidential...
Page 4
3.6.2 Configuring the Radio Carriers ....................157 3.6.3 Creating an XPIC Group ......................157 3.6.4 Performing Antenna Alignment for XPIC ................. 158 Configuring Unit Protection with HSB Radio Protection (External Protection) ....... 160 Page 4 of 825 Ceragon Proprietary and Confidential...
Page 5
4.8.2 Viewing Current Backup Files....................211 4.8.3 Setting the Configuration Management Parameters ............... 212 4.8.4 Exporting a Configuration File ....................214 4.8.5 Importing a Configuration File ....................215 4.8.6 Deleting a Configuration File....................216 Page 5 of 825 Ceragon Proprietary and Confidential...
Page 6
Configuring Ethernet Interfaces ....................281 Configuring Automatic State Propagation and Link Loss Forwarding ........284 Viewing Ethernet PMs and Statistics ..................288 6.5.1 RMON Statistics ........................288 6.5.2 Egress CoS Statistics ......................... 289 Page 6 of 825 Ceragon Proprietary and Confidential...
Page 7
8.1.3 Editing an ABN Entity ....................... 340 8.1.4 Deleting an ABN Entity ......................341 8.1.5 Viewing the Statistics for an ABN Entity .................. 341 Configuring LLDP ........................342 8.2.1 LLDP Overview ......................... 342 Page 7 of 825 Ceragon Proprietary and Confidential...
Page 8
Viewing Alarm Statistics ......................413 11.3 Viewing and Saving the Event Log ................... 413 11.4 Editing Alarm Text and Severity and Disabling Alarms and Events .......... 415 11.4.1 Displaying Alarm Information ....................415 Page 8 of 825 Ceragon Proprietary and Confidential...
Page 9
13.13 Configuring the Radio Parameters (CLI) ................... 460 13.13.1 Entering Radio View (CLI) ..................460 13.13.2 Muting and Unmuting a Radio (CLI) ............... 461 13.13.3 Configuring the Transmit (TX) Frequency (CLI) ............462 Page 9 of 825 Ceragon Proprietary and Confidential...
Page 10
14.6.4 Configuring 2+2 HSB Protection on an IP-20C or IP-20C-HP Unit (CLI) ........490 14.6.5 Viewing the Configuration of the Standby unit (CLI) ............... 491 14.6.6 Editing Standby Unit Settings (CLI)................... 491 14.6.7 Viewing Link and Protection Status and Activity (CLI) ............. 492 Page 10 of 825 Ceragon Proprietary and Confidential...
Page 11
Setting the Unit to the Factory Default Configuration (CLI) ............. 522 15.8 Performing a Hard (Cold) Reset (CLI) ..................523 15.9 Configuring Unit Parameters (CLI) ................... 523 15.10 Configuring NTP (CLI) ....................... 524 Page 11 of 825 Ceragon Proprietary and Confidential...
Page 12
17.3.1 Entering Interface View (CLI) ....................586 17.3.2 Displaying the Operational State of the Interfaces in the Unit (CLI) ........588 17.3.3 Viewing Interface Attributes (CLI) .................... 588 17.3.4 Configuring an Interface’s Media Type (CLI) ................588 Page 12 of 825 Ceragon Proprietary and Confidential...
Page 13
18.5.3 Configuring Service Bundle Shapers (CLI) ................632 18.5.4 Configuring Egress Line Compensation for Shaping (CLI) ............635 18.6 Configuring Scheduling (CLI) ....................636 18.6.1 Overview of Egress Scheduling (CLI) ..................636 Page 13 of 825 Ceragon Proprietary and Confidential...
Page 14
21.2.2 Configuring Password Strength Enforcement (CLI) ..............684 21.2.3 Forcing Password Change Upon First Login (CLI) ..............685 21.2.4 Displaying the System Password Settings (CLI) ................ 685 21.3 Configuring Users (CLI) ......................685 Page 14 of 825 Ceragon Proprietary and Confidential...
Page 17
Data Port ........................ 760 23.13.3 DC ........................... 761 23.14 PoE Injector LEDs ........................761 23.14.1 Radio LED ....................... 761 Section V: Appendices....................762 24. Alarms List ......................763 25. Abbreviations ....................... 819 Page 17 of 825 Ceragon Proprietary and Confidential...
Page 18
Figure 33: MRMC Symmetrical Scripts Page – Configuration – Adaptive Mode (IP-20E) ...... 90 Figure 34: Frequency Scanner Page ....................... 94 Figure 35: Frequency Scanner Results – Table Format ................96 Figure 36: Frequency Scanner Results – Graph Format ................. 96 Page 18 of 825 Ceragon Proprietary and Confidential...
Page 19
Figure 68: Bandwidth Notification – Add Page ..................127 Figure 69: Bandwidth Notification Page (Populated with Radio BNM) ..........127 Figure 70: Multi-Carrier ABC Group Page (Empty) ................128 Figure 71: Create ABC Group Wizard – First Page ................129 Page 19 of 825 Ceragon Proprietary and Confidential...
Page 20
Figure 105: Standby Tab of Radio Parameters Page ................165 Figure 106: Unit Redundancy Page ......................166 Figure 107: Create Diversity Group – Page 1 ..................168 Figure 108: Create Space Diversity Group – Selection Summary ............169 Page 20 of 825 Ceragon Proprietary and Confidential...
Page 21
Figure 141: Trap Managers Page ......................198 Figure 142: Trap Managers - Edit Page ....................198 Figure 143: FileZilla Server User Configuration ..................200 Figure 144: FileZilla Server Shared Folder Setup ..................201 Figure 145: FTP Port Page ........................202 Page 21 of 825 Ceragon Proprietary and Confidential...
Page 22
Figure 178: Radio BER Thresholds – Edit Page ..................246 Figure 179: MRMC Status Page ......................246 Figure 180: MRMC PM Report Page .....................247 Figure 181: Counters Page – Multi-Carrier ...................249 Figure 182: Counters Page – Single-Carrier ..................249 Page 22 of 825 Ceragon Proprietary and Confidential...
Page 23
Figure 216: Ethernet Port Tx Threshold Page ..................293 Figure 217: Ethernet Port RX PM Report Page ..................293 Figure 218: Ethernet PM Port Admin Page ..................294 Figure 219: Ethernet Port Rx Threshold Page ..................295 Page 23 of 825 Ceragon Proprietary and Confidential...
Page 25
Figure 290: Access Control User Profiles Page ..................376 Figure 291: Access Control User Profiles - Add Page ................377 Figure 292: Access Control User Accounts Page ..................378 Figure 293: Access Control User Accounts - Add Page .................378 Page 25 of 825 Ceragon Proprietary and Confidential...
Page 27
Figure 363: IP-20E Interfaces – ESS ......................748 Figure 364: IP-20E Interfaces – ESP ......................749 Figure 365: Two-Wire to PoE Port Power Adaptor ................751 Figure 366: RSL Pins ..........................751 Figure 367: IP-20V Interfaces .......................755 Page 27 of 825 Ceragon Proprietary and Confidential...
Page 28
User Guide for FibeAir® IP-20 All-Outdoor Products, CeraOS 10.5 Figure 368: Two-Wire to PoE Port Power Adaptor ................756 Figure 369: RSL Pins ..........................757 Figure 370: PoE Injector Connectors ....................760 Page 28 of 825 Ceragon Proprietary and Confidential...
Page 29
Table 31: SFP Digital Diagnostic Monitoring (DDM) Parameters ............224 Table 32: Radio Status Parameters ......................228 Table 33: Remote Radio Parameters ....................230 Table 34: Radio Ethernet Interface Counters Fields ................238 Table 35: MRMC Status Parameters ....................247 Table 36: MRMC PMs ...........................248 Page 29 of 825 Ceragon Proprietary and Confidential...
Page 30
Table 68: LLDP Statistics ........................356 Table 69: LLDP Port TX Statistics ......................357 Table 70: LLDP Port RX Statistics ......................357 Table 71: Sync Source Parameters .......................362 Table 72: Alarm Information ........................412 Table 73: Event Log Information ......................414 Page 30 of 825 Ceragon Proprietary and Confidential...
Page 31
Table 106: Unit Parameters CLI Parameters ..................524 Table 107: NTP CLI Parameters ......................524 Table 108: SFP Inventory Parameters (CLI) ..................527 Table 109: SFP Digital Diagnostic Monitoring (DDM) Parameters (CLI) ..........528 Table 110: Remote Radio Mute/Unmute CLI Parameters ..............531 Page 31 of 825 Ceragon Proprietary and Confidential...
Page 32
Table 144: Service Bundle CLI Parameters ...................578 Table 145: VLAN Bundle to Service Point CLI Parameters ..............579 Table 146: Display Service Point Attributes CLI Parameters ..............580 Table 147: Delete Service Point Attributes CLI Parameters ..............580 Page 32 of 825 Ceragon Proprietary and Confidential...
Page 33
Table 182: Assigning Rate Meter for Broadcast Traffic CLI Parameters ..........619 Table 183: Assigning Rate Meter per Ethertype CLI Parameters ............620 Table 184: Assigning Line Compensation Value for Rate Meter CLI Parameters .........621 Page 33 of 825 Ceragon Proprietary and Confidential...
Page 36
User Guide for FibeAir® IP-20 All-Outdoor Products, CeraOS 10.5 Table 259: PoE Injector RJ-45 Data Port Supporting 10/100/1000Base-T ...........760 Table 260: Alarms ..........................763 Table 261: Abbreviations ........................819 Page 36 of 825 Ceragon Proprietary and Confidential...
Page 37
Do not look into coaxial connectors at closer than reading distance (30 cm). Do not look into an open waveguide unless you are absolutely sure that the power is turned off. Page 37 of 825 Ceragon Proprietary and Confidential...
Page 38
Restricted Access Area: DC powered equipment should only be installed in a Restricted Access Area. Installation Codes: The equipment must be installed according to country national electrical codes. For North America, equipment must be installed in accordance Page 38 of 825 Ceragon Proprietary and Confidential...
Page 39
är kopplad till kabel-TV nät kan i vissa fall medfőra risk főr brand. Főr att undvika detta skall vid anslutning av utrustningen till kabel-TV nät galvanisk isolator finnas mellan utrustningen och kabel-TV nätet. Page 39 of 825 Ceragon Proprietary and Confidential...
Page 40
Gefahrenrisiko: Durch Abtrennen einer Stromquelle wird nur ein Stromversorgungsmodul abgetrennt. Um die Einheit vollständig zu isolieren, trennen Sie alle Stromversorgungen ab. Maschinenlärminformations-Verordnung - 3. GPSGV, der höchste Schalldruckpegel beträgt 70 dB(A) oder weniger gemäß EN ISO 7779. Page 40 of 825 Ceragon Proprietary and Confidential...
IP-20E • IP-20V • Each of these products except IP-20C-HP can be used with a Ceragon-approved PoE Injector. Wherever applicable, the manual notes the specific distinctions between these products. The manual also notes when specific features are only applicable to certain products and not others.
For example, an IP-20C configuration file can only be restored to an IP-20C with the same part number as the unit from which it was saved. Page 45 of 825 Ceragon Proprietary and Confidential...
IP-20S is an all-outdoor solution for backhaul sites. It runs under CeraOS, the high- performance, internetworking operating system, and supports all common features of the IP-20 platform in a compact, environmentally friendly architecture. Page 46 of 825 Ceragon Proprietary and Confidential...
IP-20V runs the same CeraOS software as the rest of the FibeAir IP-20 platform, enabling it to provide the same Ethernet services model and other advanced radio, Ethernet, and management features as IP-20C, IP-20C-HP, IP-20S, IP-20E, and IP-20V. Page 47 of 825 Ceragon Proprietary and Confidential...
DC power supply to the IP-20C, IP-20S, IP-20E, or IP-20V unit. To do so, the PoE injector combines 48VDC input and GbE signals via a standard CAT5E cable using a proprietary Ceragon design. The PoE injector can be ordered with a DC feed protection and with +24VDC support, as well as EMC surge protection for both indoor and outdoor installation options.
The following products are included in the FibeAir IP-20 Assured platform: • FibeAir IP-20C Assured • FibeAir IP-20S Assured Note: CeraOS 10.5 cannot be used in FibeAir IP-20 Assured platforms. For FibeAir IP-20 Assured, use CeraOS 8.3. Page 49 of 825 Ceragon Proprietary and Confidential...
IP-20 system. Some of the pages and tasks described in this Manual may not be available to all users, based on the actual system configuration, activation key, and other details. Page 50 of 825 Ceragon Proprietary and Confidential...
◦ Click to hide the sub-options under a menu item. The main section of the page provides the page's basic functionality. • Figure 1: Main Web EMS Page Page 51 of 825 Ceragon Proprietary and Confidential...
Figure 2: Displaying a Representation of the Front Panel Figure 3: Main Web EMS Page with Representation of Front Panel – IP-20C and IP-20S Figure 4: Main Web EMS Page with Representation of Front Panel – IP-20C-HP Page 52 of 825 Ceragon Proprietary and Confidential...
Active or Standby TCC. For details on configuring HSB radio protection, see Configuring Unit Protection with HSB Radio Protection (External Protection). Note: HSB protection is only available for IP-20C and IP-20S. Page 53 of 825 Ceragon Proprietary and Confidential...
Certain pages include a Related Pages drop-down list on the upper right of the main section of the page. You can navigate to a page related to the current page by selecting the page from this list. Figure 8: Related Pages Drop-Down List Page 54 of 825 Ceragon Proprietary and Confidential...
Select only the columns you want to display and click again. Note: When one or more columns are hidden, the icon turns white ( ). Figure 10: Unit Summary Page – Customizing Columns Page 55 of 825 Ceragon Proprietary and Confidential...
A list of columns is displayed. Select only the columns you want to display and click again. Note: When one or more columns are hidden, the icon turns white ( ). Page 56 of 825 Ceragon Proprietary and Confidential...
User Guide for FibeAir® IP-20 All-Outdoor Products, CeraOS 10.5 Figure 12: Radio Summary Page – Customizing Columns Page 57 of 825 Ceragon Proprietary and Confidential...
Activation Key > Activation Key Overview Displaying a List of Activation-Key-Enabled Features Security > General > Configuration Operating in FIPS Mode Security > General > Security Log Upload Uploading the Security Log Page 58 of 825 Ceragon Proprietary and Confidential...
Radio BER Thresholds Configuring BER Thresholds and Displaying Current BER ATPC Configuring ATPC and ATPC Override Timer Payload Encryption Configuring AES-256 Payload Encryption Ethernet Interface > Configuration Configuring Header De-Duplication and Frame Cut-Through Page 59 of 825 Ceragon Proprietary and Confidential...
Table 5: IP-20 Web EMS Menu Hierarchy – Ethernet Menu Sub-Menus For Further Information General Configuration Setting the MRU Size and the S-VLAN Ethertype Services Configuring Ethernet Service(s) Interfaces > Physical Interfaces Configuring Ethernet Interfaces Page 60 of 825 Ceragon Proprietary and Confidential...
Page 61
Configuring Adaptive Bandwidth Notification (ABN) Configuring Multiband (Enhanced Multi-Carrier ABC) Protocols > LLDP > Remote Management Displaying Peer Status Protocols > LLDP > Advanced > Configuration > Configuring the General LLDP Parameters Parameters Page 61 of 825 Ceragon Proprietary and Confidential...
Table 6: IP-20 Web EMS Menu Hierarchy – Sync Menu Sub-Menus For Further Information SyncE Regenerator Configuring SyncE Regenerator Sync Source Configuring the Sync Source Outgoing Clock Configuring the Outgoing Clock and SSM Messages Page 62 of 825 Ceragon Proprietary and Confidential...
Table 8: IP-20 Web EMS Menu Hierarchy – Utilities Menu Sub-Menus For Further Information Restart HTTP Restarting the HTTP Server ifIndex Calculator Calculating an ifIndex MIB Reference Guide Displaying, Searching, and Saving a list of MIB Entities Page 63 of 825 Ceragon Proprietary and Confidential...
User Guide for FibeAir® IP-20 All-Outdoor Products, CeraOS 10.5 Section II: Web EMS Configuration Page 64 of 825 Ceragon Proprietary and Confidential...
Connect the IP-20 unit to a PC by means of a TP cable. The cable is connected to the MGT port on the IP-20 and to the LAN port on the PC. Refer to the Installation Guide for the type of unit you are connecting for cable connection instructions. Page 65 of 825 Ceragon Proprietary and Confidential...
3 Select Local Area Connection > Properties > Internet Protocol Version 4 (TCP/IP), and set the following parameters: ◦ IP address: 192.168.1.10 ◦ Subnet mask 255.255.255.0 ◦ No default gateway 4 Click OK to apply the settings. Figure 13: Internet Protocol Properties Window Page 66 of 825 Ceragon Proprietary and Confidential...
If the unit's IP address has been changed from its default of 192.168.1.1, and you do not know the new IP address, you can log into the unit by establishing a connection directly to the CPU. This requires a Ceragon Networks proprietary Ethernet cable. This cable should be ordered from Ceragon Networks, according to the following table.
Page 68
User Name: admin ◦ Password: admin 7 Click Apply. 8 After a connection is established, you can view or configure the unit's IP address using the Web EMS. See Changing the Management IP Address. Page 68 of 825 Ceragon Proprietary and Confidential...
In addition to the Admin password, there is an additional password protected user account, “root user”, which is configured in the system. The root user password and instructions for changing this password are available from Ceragon Customer Support. It is strongly recommended to change this password.
Point-to-Point ◦ Multipoint The pre-defined configuration file is generated by Ceragon Global Services and provided as a service. The pre-defined configuration file must be compatible with the CeraOS version the IP-20 device is running. Configuration files created for CeraOS 9.2 cannot be used with later CeraOS versions.
Note: If the pre-defined configuration file included a new IP address for the unit, make sure to configure an IP address on the PC or laptop you are using to perform the configuration within the same subnet as the IP-20 unit’s new IP address. Page 71 of 825 Ceragon Proprietary and Confidential...
IP-20 unit. To use the Platform Setup page: 1 Select Quick Configuration > Platform Setup. The Quick Configuration – Platform Setup page opens. Figure 18: Quick Configuration – Platform Setup Page Page 72 of 825 Ceragon Proprietary and Confidential...
Page 73
If you set Demo admin to Disable, the Activation Key field is displayed. Enter a valid activation key in this field. For a full explanation of activation keys, see Configuring the Activation Key. Page 73 of 825 Ceragon Proprietary and Confidential...
7 Click Finish. The Selection Summary page opens. To go back and change any of the parameters, click Back. To implement the new parameters, click Submit. Figure 19: Quick Configuration – Platform Setup Summary Page Page 74 of 825 Ceragon Proprietary and Confidential...
Note: In order to use in-band management, it must be supported on the external switch. For instructions on adding service points, see Configuring Service Points. Page 75 of 825 Ceragon Proprietary and Confidential...
7 If you entered an IPv6 address, enter the IPv6 prefix length in the IPv6 Prefix- Length field. 8 Optionally, if you entered an IPv6 address, enter the default gateway in IPv6 format in the Default Gateway IPv6 field. 9 Click Apply. Page 76 of 825 Ceragon Proprietary and Confidential...
The 60-day period is only counted when the system is powered up. 10 days before demo mode expires, an alarm is raised indicating that demo mode is about to expire. Page 77 of 825 Ceragon Proprietary and Confidential...
Violation runtime counter (hours) In the event of an Activation Key Violation alarm, this field displays the number of hours remaining in the 48- hour activation key violation grace period. Page 78 of 825 Ceragon Proprietary and Confidential...
300M and later purchased one upgrade activation key to 350M, credit is given as if the customer had purchased one activation key for 350M and one activation key for 300M. Page 79 of 825 Ceragon Proprietary and Confidential...
Page 80
User Guide for FibeAir® IP-20 All-Outdoor Products, CeraOS 10.5 For instructions on how to reclaim an activation key, refer to the User Guide for the Ceragon Activation Key Management System, Rev A.15 or later, Chapter 7, Reclaiming an Activation Key.
Indicates whether the feature is allowed under the activation key that is currently installed in the unit. Activation key violation status Indicates whether the system configuration violates the currently installed activation key with respect to this feature. Page 81 of 825 Ceragon Proprietary and Confidential...
To display and configure the UTC parameters: 1 Select Platform > Management > Time Services. The Time Services page opens. Figure 23: Time Services Page 2 Configure the fields listed in Table 12. Page 82 of 825 Ceragon Proprietary and Confidential...
The month when Daylight Savings Time ends. The date in the month when Daylight Savings Time ends. DST Offset (Hours) The required offset, in hours, for Daylight Savings Time. Only positive offset is supported. Page 83 of 825 Ceragon Proprietary and Confidential...
To enable or disable an individual interface: 1 Select the interface in the Interface Manager table. 2 Click Edit. The Interface Manager – Edit page opens. Figure 25: Interface Manager – Edit Page Page 84 of 825 Ceragon Proprietary and Confidential...
Manager Table, select Admin status – Up or Admin status – Down. Figure 26: Multiple Selection Operation Section (Interface Manager Page) 3 Click Apply. Note: The Operational Status field displays the current, actual operational state of the interface (Up or Down). Page 85 of 825 Ceragon Proprietary and Confidential...
Release Notes for the CeraOS version you are using. The following figures show scripts supported by the IP-20C and IP-20E. Figure 27: MRMC Symmetrical Scripts Page (IP-20C) (ETSI) Page 86 of 825 Ceragon Proprietary and Confidential...
3 Select the script you want to assign to the radio. The currently-assigned script is marked by a check mark (Script ID 1504 in the image above). 4 Click Configure Script. A separate MRMC Symmetrical Scripts page opens similar to the page shown below. Page 87 of 825 Ceragon Proprietary and Confidential...
In Adaptive ACM mode, Tx and Rx rates are dynamic. An ACM-enabled radio system automatically chooses which profile to use according to the channel fading conditions. If you select Adaptive, two fields are displayed enabling you to select minimum and maximum ACM profiles. Page 89 of 825 Ceragon Proprietary and Confidential...
Adaptive ACM mode only: The maximum profile for the script. For example, if you select a maximum profile of 5, the system will not climb above profile 5, even if channel fading conditions allow it. Page 91 of 825 Ceragon Proprietary and Confidential...
◦ Single Mode – The frequency scanner scans each channel in the script once, over the defined frequency range. For each channel, the Web EMS will display the measured interference level. Page 94 of 825 Ceragon Proprietary and Confidential...
Page 95
In Single Mode, the same as the RSL Sample Value. Maximum RSL (dBm) – In Continuous Mode, the highest RSL value measured • for the scanned channel. In Single Mode, the same as the RSL Sample Value. Page 95 of 825 Ceragon Proprietary and Confidential...
Maximum RSL (dBm) – In Continuous Mode, the highest RSL value measured for the scanned channel. In Single Mode, the same as the RSL Sample Value. Figure 36: Frequency Scanner Results – Graph Format Page 96 of 825 Ceragon Proprietary and Confidential...
For multi-carrier units, the Radio Parameters page initially displays a table as shown in Figure 37. ◦ For single-carrier units, a page appears, similar to Figure 38 (which shows an IP-20C/IP-20C-HP page). Figure 37: Radio Parameters Page – IP-20C/IP-20C-HP Page 97 of 825 Ceragon Proprietary and Confidential...
Edit. A separate Radio Parameters page opens. The page is essentially identical to the IP-20S, IP-20E, and IP-20V page, except for the addition of a Radio location parameter. Figure 38: Radio Parameters Page Per Carrier – IP-20C/IP-20C-HP Page 98 of 825 Ceragon Proprietary and Confidential...
Page 99
ID is not the same at both sides of the link, a Link ID Mismatch alarm is raised. If Link ID Mismatch Security is enabled, traffic is also blocked on the link. See Enabling Link ID Mismatch Security. Page 99 of 825 Ceragon Proprietary and Confidential...
To display the current Link ID Mismatch Security setting, enter the following command in root view: root> platform security link-id mismatch security show admin By default, Link ID Mismatch Security is disabled. Page 100 of 825 Ceragon Proprietary and Confidential...
2 For multi-carrier units, select the carrier in the Radio table (see Figure 37) and click Edit. A separate Radio Parameters page opens. The page is essentially identical to the single-carrier page, except for the addition of a Radio location parameter. Page 101 of 825 Ceragon Proprietary and Confidential...
Figure 39: Radio Parameters Page Per Carrier – IP-20C 3 In the Adaptive TX power admin field, select Enable. The Adaptive TX power operational status field should now indicate Up to indicate that the feature is fully functional. Page 102 of 825 Ceragon Proprietary and Confidential...
2.17.1 Requirements for FIPS Compliance For a full list of FIPS requirements, refer to the Ceragon IP-20 FIPS 140-2 Security Policy, available upon request. It is the responsibility of the customer to ensure that these requirements are met.
After any system reset, the length of time before users can log back into the system is longer than usual due to FIPS-related self-testing. For a full list of FIPS requirements, including software configuration requirements, refer to the Ceragon IP-20 FIPS 140-2 Security Policy, available upon request. 2.18 Configuring Grouping (Optional) At this point in the configuration process, you should configure any interface groups that need to be set up according to your network plan.
Configuring 1+1 HSB with Space Diversity MIMO and Space Diversity IP-20C Configuring MIMO and Space Diversity AFR 1+0 IP-20C (hub site or tail site) Configuring Advanced Frequency IP-20S (tail site only) Reuse (AFR) Page 105 of 825 Ceragon Proprietary and Confidential...
Because the Quick Configuration wizard creates Pipe links, you cannot add an interface to a link using the Quick Configuration wizard if any service points are attached to the interface prior to configuring the link. See Deleting a Service Point. Page 106 of 825 Ceragon Proprietary and Confidential...
For a full explanation of Ethernet Services, service types, and attached interface types, see Configuring Ethernet Service(s). 5 Click Next. Page 2 of the 1+0 Quick Configuration wizard opens. Figure 42: 1+0 Quick Configuration Wizard – Page 2 Page 107 of 825 Ceragon Proprietary and Confidential...
Page 108
10 Click Next. Page 3 of the 1+0 Quick Configuration wizard opens. Page 108 of 825 Ceragon Proprietary and Confidential...
Configuring the Radio (MRMC) Script(s). ◦ Minimum profile – Enter the minimum profile for the script. See Configuring the Radio (MRMC) Script(s). 14 Click Next. Page 4 of the 1+0 Quick Configuration wizard opens. Page 109 of 825 Ceragon Proprietary and Confidential...
Figure 45: 1+0 Quick Configuration Wizard – Page 5 (Summary Page) 19 To complete configuration of the link, click Submit. If you want to go back and change any of the parameters, click Back. After you click Submit, the unit is reset. Page 110 of 825 Ceragon Proprietary and Confidential...
– All C-VLANs and untagged frames are classified into the service. Note: For a full explanation of Ethernet Services, service types, and attached interface types, see Configuring Ethernet Service(s). 6 Click Next. Page 3 of the 1+0 Repeater Quick Configuration wizard opens. Page 111 of 825 Ceragon Proprietary and Confidential...
When the timer expires, the mute automatically ends. This provides a fail- safe mechanism for maintenance operations that eliminates the possibility of accidently leaving the radio muted after the maintenance has been completed. By default, the timer is 10 minutes. Page 112 of 825 Ceragon Proprietary and Confidential...
If you selected Fixed in the Operational Mode field, the next field is Profile. Select the ACM profile for the radio in the Profile field. ◦ If you selected Adaptive in the Operational Mode field, the following two fields are displayed: Page 113 of 825 Ceragon Proprietary and Confidential...
16 Click Finish. Page 6 of the 1+0 Repeater Quick Configuration wizard opens. This page displays the parameters you have selected for the link. Figure 51: 1+0 Repeater Quick Configuration Wizard – Page 6 (Summary Page) Page 114 of 825 Ceragon Proprietary and Confidential...
– All C-VLANs and untagged frames are classified into the service. Note: For a full explanation of Ethernet Services, service types, and attached interface types, see Configuring Ethernet Service(s). 5 Click Next. The Radio #2 Selection page opens. Page 115 of 825 Ceragon Proprietary and Confidential...
XPIC configuration, select the radio pair. For full instructions on configuring XPIC, including antenna alignment instructions, see Configuring XPIC. Figure 54: 2 + 0 Multi Carrier ABC Quick Configuration Wizard – Radio XPIC Configuration Page Page 116 of 825 Ceragon Proprietary and Confidential...
MRMC script and determine the current interference level for each channel. This enables you to select the best channel in accordance with current interference levels. See Running the Frequency Scanner (IP-20V). Page 117 of 825 Ceragon Proprietary and Confidential...
MRMC script parameters for each interface. For an XPIC group, you configure the parameters for the group rather than the individual interfaces. Figure 57: 2 + 0 Multi Carrier ABC Quick Configuration Wizard – Radio MRMC Script Configuration Page Page 118 of 825 Ceragon Proprietary and Confidential...
Maximum profile – Enter the maximum profile for the script. See Configuring the Radio (MRMC) Script(s). ◦ Minimum profile – Enter the minimum profile for the script. See Configuring the Radio (MRMC) Script(s). Page 119 of 825 Ceragon Proprietary and Confidential...
20 To complete configuration of the Multi-Carrier ABC group, click Submit. If you want to go back and change any of the parameters, click Back. After you click Submit, the unit is reset. Page 120 of 825 Ceragon Proprietary and Confidential...
6 In the Ethernet Interface field, select the port connected to the external switch. This should be Ethernet: Slot 1, Port 1. 7 In the Radio #1 Interface field, select Radio: Slot 2, Port 1. Page 121 of 825 Ceragon Proprietary and Confidential...
Failure to properly set this parameter may lead to frequent pauses as the queue fills up during low capacity periods, such as when weather conditions cause the ACM profile to drop. Page 122 of 825 Ceragon Proprietary and Confidential...
Maximum profile – Enter the maximum profile for the script. See Configuring the Radio (MRMC) Script(s). ◦ Minimum profile – Enter the minimum profile for the script. See Configuring the Radio (MRMC) Script(s). Page 124 of 825 Ceragon Proprietary and Confidential...
If you want to manage the IP-20C or IP-20S via the IP-20E, refer to the instructions in Inband Management via the IP-20E. 21 Click Finish. The Summary page opens. This page displays the parameters you have selected for the group. Page 125 of 825 Ceragon Proprietary and Confidential...
See Configuring Automatic State Propagation and Link Loss Forwarding. 3 Configure Bandwidth Notification: Select Ethernet > Protocols > Bandwidth Notification. The Bandwidth Notification page opens. Figure 67: Bandwidth Notification Page (Empty) Page 126 of 825 Ceragon Proprietary and Confidential...
In the Monitored Interface field, select the interface or group connected to the IP-20E. vii Click Apply. The configuration is added to the Bandwidth Notification page with the Protocol Type Radio BNM. Figure 69: Bandwidth Notification Page (Populated with Radio BNM) Page 127 of 825 Ceragon Proprietary and Confidential...
1 Select Radio > Groups > Multi Carrier ABC. The Multi Carrier ABC page opens. Figure 70: Multi-Carrier ABC Group Page (Empty) 2 Click Create Group. The first page of the Create ABC Group wizard opens. Page 128 of 825 Ceragon Proprietary and Confidential...
Radio slot 2 port 2 is selected second. 8 Click Next. The next page of the Create Group wizard opens. 9 In the Member 2 field, select a radio interface. 10 Click Next. A summary page opens. Page 129 of 825 Ceragon Proprietary and Confidential...
Enable the LAG group shutdown in case of degradation event option on the upstream IP-20 unit. Notes: When using in-band management, management is lost in the event of radio failure and returns when the radio link is restored. Page 130 of 825 Ceragon Proprietary and Confidential...
Multi-Carrier ABC group, since you must remove the members individually before deleting the group. To remove interfaces: 1 Select the group in the Multi-Carrier ABC table and click Add/Remove Members. The Add/Remove Members page opens. Page 131 of 825 Ceragon Proprietary and Confidential...
3 Remove each member of the group. See Adding and Removing Group Members. 4 Click Close to close the Multi Carrier ABC – Add/Remove Members page. 5 Select the group and click Delete. Page 132 of 825 Ceragon Proprietary and Confidential...
2+0 Multi-Carrier ABC group, and transmitted. To ensure a smooth traffic flow, the following must be configured on the IP-20C or IP-20S: • Automatic State Propagation, with ASP trigger by remote fault enabled. • Bandwidth Notification. Page 133 of 825 Ceragon Proprietary and Confidential...
Figure 78: Create ABC Group Wizard – Page 1 iii In the Group ID field, select Enhanced Multi Carrier ABC (Group #1). iv Optionally, in the Group Name field, enter a descriptive name for the group. Page 135 of 825 Ceragon Proprietary and Confidential...
Click Next. Page 3 of the Create ABC Group wizard opens. Figure 80: Create ABC Group Wizard – Page 3 viii In the Member #2 field under Member Selection, select Ethernet: Slot 1, Port 2. Page 136 of 825 Ceragon Proprietary and Confidential...
ACM profile to drop. Click Finish. The Selection Summary page of the Create ABC Group wizard opens. Figure 81: Create ABC Group Wizard – Page 3 Page 137 of 825 Ceragon Proprietary and Confidential...
See Configuring Automatic State Propagation and Link Loss Forwarding. 8 On the IP-20C or IP-20S, configure Bandwidth Notification: Select Ethernet > Protocols > Bandwidth Notification. The Bandwidth Notification page opens. Figure 83: Bandwidth Notification Page (Empty) Page 138 of 825 Ceragon Proprietary and Confidential...
In the Monitored Interface field, select the interface or group connected to the IP-20E. vii Click Apply. The configuration is added to the Bandwidth Notification page with the Protocol Type Radio BNM. Figure 85: Bandwidth Notification Page (Populated with Radio BNM) Page 139 of 825 Ceragon Proprietary and Confidential...
IP-20E IP-20S Figure 86: Multiband Cable for Use with CSFP Port Table 18: Multiband Cable for Use with CSFP Port Cable Marketing Model Cable Description IP-20_FO_SM_LC2SNG2LC_ARM_5m CABLE,FO,DUAL LC TO LC/LC SPLIT,5.3M,SM,3xM28 GLAND,OUTDOOR Page 140 of 825 Ceragon Proprietary and Confidential...
IP-20E and Eth3 on the IP-20E. This transmits management to Eth3 on the IP-20C or IP-20S. See Configuring In-Band Management. Note: To avoid loops, in-band management must not be configured on the slave unit. Page 141 of 825 Ceragon Proprietary and Confidential...
IP-20E (ESP) GbE Port Traffic Power Eth1/PoE Eth2 Power Management (IP-20C) Source Eth 3 MGT/PROT IP-20C or IP-20S (ESS) Figure 88: Multiband Configuration with Direct Inband Management to the IP-20C or IP-20S Page 142 of 825 Ceragon Proprietary and Confidential...
External Switch IP-20E (ESP) Traffic Power Eth1/PoE Power Source Eth2 Eth 3 Management (IP-20C/IP-20S) MGT/PROT IP-20C or IP-20S (ESS) Figure 89: Multiband Configuration with Direct Inband Management to the IP-20C or IP-20S Page 143 of 825 Ceragon Proprietary and Confidential...
When using Multi-Carrier ABC, configure both radios as synchronization sources. In ring configurations, configure priority order in the direction of traffic on the ring. For instructions on configuring SyncE, see Configuring the Sync Source. Page 144 of 825 Ceragon Proprietary and Confidential...
“down”. This restriction does not apply to radio interfaces. For instructions on setting the administrative state of an interface, see Enabling the Interfaces (Interface Manager). Page 145 of 825 Ceragon Proprietary and Confidential...
LACP on the LAG. The default value is Disable. 5 In the Member 1 field, select an interface to assign to the LAG group. Only interfaces not already assigned to a LAG group appear in the dropdown list. Page 146 of 825 Ceragon Proprietary and Confidential...
LAG group was not created and giving the reason. 3.5.2.2 Editing a LAG Group To edit an existing LAG group: 1 Select Ethernet > Interfaces > Groups > LAG. The LAG page opens. Page 147 of 825 Ceragon Proprietary and Confidential...
Disabling LAG Group Shutdown in Case of Degradation Event . 3.5.3 Enabling and Disabling LAG Group Shutdown in Case of Degradation Event Note: LAG Group Shutdown in Case of Degradation Event cannot be used with LACP. Page 148 of 825 Ceragon Proprietary and Confidential...
To configure enhanced LAG distribution: 1 Select Ethernet > Interfaces > Groups > LAG. The LAG page opens. 2 Click LAG DF underneath the Link Aggregation table. The LAG Distribution Function (DF) page opens. Page 149 of 825 Ceragon Proprietary and Confidential...
1 Select the LAG groups in the Link Aggregation table or select all the LAG groups by selecting the check box in the top row. 2 Click Delete underneath the Link Aggregation table. Page 150 of 825 Ceragon Proprietary and Confidential...
The MAC address value used as a unique identifier for the system that contains this Aggregator. Actor System Priority The priority value associated with the Actor’s System ID. Actor Operational Key The current operational value of the Key for the Aggregator. Page 151 of 825 Ceragon Proprietary and Confidential...
3.5.6.2 Displaying LACP Port Status Parameters To display LACP port status parameters: 1 Select Ethernet > Protocols > LACP > Port > Status to open the LACP Port Status page. Figure 96: LACP Port Status Page Page 152 of 825 Ceragon Proprietary and Confidential...
Indicates whether the Aggregation Port is able to aggregate or is only able to operate as an individual link. Actor System ID The MAC Address value that defines the value of the System ID for the system that contains this Aggregation Port. Page 153 of 825 Ceragon Proprietary and Confidential...
Page 154
System Priority Partner Administrative The current administrative value of the port number for the protocol Port partner. Partner Administrative The current administrative value of the port priority for the protocol Port Priority partner. Page 154 of 825 Ceragon Proprietary and Confidential...
The number of LACPDUs that this port has received. Unknown RX The number of unknown protocol frames that this port has received. Illegal RX The number of illegal protocol frames that this port has received. Page 155 of 825 Ceragon Proprietary and Confidential...
The state of the Mux state machine for the Aggregation port. Possible values are Collecting, Distributing, Attached, and Detached. Debug Mux Reason A text string indicating the reason for the most reason change in the state of the Mux machine. Page 156 of 825 Ceragon Proprietary and Confidential...
3 In the XPIC page, create an XPIC group that consists of the two RMCs that will be in the XPIC group. See Creating an XPIC Group. 3.6.3 Creating an XPIC Group To create an XPIC group: 1 Select Radio > Groups > XPIC. The XPIC page opens. Page 157 of 825 Ceragon Proprietary and Confidential...
RSL of the second carrier link (the “RSL ”), measure the RSL of the wanted first carrier (the “RSL ”) and determine the XPI. The XPI should unwanted match the XPI with the second carriers muted. Page 158 of 825 Ceragon Proprietary and Confidential...
Page 159
XPI to make sure it subsequently exceeds 25dB. A normal XPI level in clear sky conditions is between 25 and 30dB. Page 159 of 825 Ceragon Proprietary and Confidential...
• Split Protection Mode – Only available for optical Ethernet ports. An optical splitter cable is used to connect to both the active and the standby optical Ethernet ports. Page 160 of 825 Ceragon Proprietary and Confidential...
Select the interface and click Edit. The Logical Interfaces – Edit page opens. Figure 101: Logical Interfaces – Edit Page iii In the Interface Mode field, select LACP. iv Click Apply, then Close. Page 161 of 825 Ceragon Proprietary and Confidential...
Protection Administration, the system will determine which unit becomes the Active unit. 2 Select Platform > Shelf Management > Unit Redundancy. The Unit Redundancy (HSB Protection) page opens. Figure 102: Unit Redundancy Page Page 162 of 825 Ceragon Proprietary and Confidential...
Standby unit parameters. Even when a switchover occurs, the unit displayed in the Web EMS is always the currently Active unit. Note: The parameters that are editable on the Standby tab are described in Editing Standby Unit Settings. Page 163 of 825 Ceragon Proprietary and Confidential...
To enable the second radio carrier on both units, use the Interface Manager page (see Figure 24). The following figure shows the Interface Manager page with both radio carriers enabled. Figure 104: Interface Manager Page – Both Radio Carriers Enabled Page 164 of 825 Ceragon Proprietary and Confidential...
Activation Key). • Defining user accounts – Refer to the Access Control User Accounts Page (see Configuring Users). Setting synchronization settings – Refer to the SyncE Regenerator • page (see Configuring SyncE Regenerator). Page 165 of 825 Ceragon Proprietary and Confidential...
At any point, you can manually switch to the Standby unit, provided that the highest protection fault level in the Standby unit is no higher than the highest protection fault level on the Active unit. Page 166 of 825 Ceragon Proprietary and Confidential...
To disable protection: 1 Select Platform > Shelf Management > Unit Redundancy. The Unit Redundancy (HSB Protection) page opens (Figure 102). 2 Select Disable in the Protection Admin field. 3 Click Apply. Page 167 of 825 Ceragon Proprietary and Confidential...
Figure 107: Create Diversity Group – Page 1 3 Click Create Group. The Create MIMO Group page opens. 4 In the Group Type field, select 1+0 Space Diversity. 5 Click Next. The Selection Summary page opens. Page 168 of 825 Ceragon Proprietary and Confidential...
8 In the Admin state field, select Enable. 9 Click Apply. 10 Repeat Steps 1 through 9 for the second unit. Note: The identity of the active and standby units is not determined until unit protection is configured. Page 169 of 825 Ceragon Proprietary and Confidential...
Page 170
If you mute the interface before configuring unit protection, you must make sure to manually mute the interface on both IP-20 units. Otherwise, configuring unit protection will override the mute configuration. Page 170 of 825 Ceragon Proprietary and Confidential...
In effect, a 2+2 HSB configuration is a protected 2+0 Space Diversity configuration. Each IP-20C monitors both of its cores. If the active IP-20C detects a radio failure in either of its cores, it initiates a switchover to the standby IP-20C. Page 171 of 825 Ceragon Proprietary and Confidential...
Guide or the IP-20C-HP Installation Guide: ◦ Source sharing cable between both EXT REF IP-20 radio connectors. ◦ MIMO data sharing cable between both IP-20 ETH3/EXT ports. ◦ MIMO signaling cable between both IP-20 MGT/PROT ports. Page 172 of 825 Ceragon Proprietary and Confidential...
Figure 110: Advanced Multi Carrier Configuration Page Click Create Group. The AMCC Group – Select Group Parameters page opens. Figure 111: 4x4 MIMO Group – Select Group Parameters Page iii In the Group Type field, select MIMO 4X4. Page 173 of 825 Ceragon Proprietary and Confidential...
In the Member #1 field, select one of the radio carriers. vii In the Member Role field, select MIMO Master if the unit is the Master unit, or MIMO Slave if the unit is the Slave unit. Page 174 of 825 Ceragon Proprietary and Confidential...
Configuring the Radio (MRMC) Script(s). Make sure the script you select supports MIMO. Note: For a list of available scripts, including an indication of which scripts support MIMO, refer to the Release Notes for the CeraOS release you are using. Page 175 of 825 Ceragon Proprietary and Confidential...
Click Submit to configure the group. If you changed the MRMC script from the script that had previously been configured, or if you set the Group Admin Status to Enable, the unit is reset. Page 176 of 825 Ceragon Proprietary and Confidential...
4 Click Next. The Create Diversity Group page is updated and displays your system configuration. Figure 118: Create Diversity Group Page – MIMO 2x2 – Page 2 5 Click Submit to create the 2x2 MIMO group. Page 178 of 825 Ceragon Proprietary and Confidential...
Figure 119: Diversity Groups – 2x2 MIMO - Edit Page In the Admin state field, select Enable. iii Click Apply. 7 In the Role field, leave the setting Not-relevant. 8 Verify that the MMI levels are appropriate. See Viewing MMI Levels. Page 179 of 825 Ceragon Proprietary and Confidential...
2+0 Space Diversity 4 Click Next. The Create Diversity Group page is updated and displays your system configuration. Figure 121: Create Diversity Group – Page 2 5 Click Submit to create the Diversity group. Page 180 of 825 Ceragon Proprietary and Confidential...
In the Role field: ◦ For 1+0 Space Diversity groups, leave the setting Not-relevant. ◦ For 2+2 Space Diversity groups, set the role of the group to Master or Slave. iv Click Apply. Page 181 of 825 Ceragon Proprietary and Confidential...
1 Select Radio > Groups> Diversity. The Diversity Groups page opens. 2 Select the 2x2 MIMO group from the table. 3 Click Edit Members. The Diversity Groups - Edit Members page opens. Figure 124: Diversity Groups - Edit Members Page Page 182 of 825 Ceragon Proprietary and Confidential...
When the MIMO or Space Diversity group is disabled, the system is automatically reset. 2 Select the group from the table. 3 Click Delete. The Delete MIMO confirmation page opens. 4 Confirm the operation. Page 183 of 825 Ceragon Proprietary and Confidential...
IP-20C or Hub Site IP-20S Dual-Modem IP-20C frequency spot Figure 125: AFR 1+0 Deployment For more detailed information about planning links with AFR, refer to the Advanced Frequency Reuse (AFR) Link Planning Guide. Page 184 of 825 Ceragon Proprietary and Confidential...
After you configure AFR on the Tails Sites, the link between the Hub Site and the Tail Sites will be lost. The links will be restored after you configure AFR on the Hub site and the Hub site comes back up after unit reset. Page 185 of 825 Ceragon Proprietary and Confidential...
◦ If you are configuring a Tail site, select AFR Tail. 4 In the Group admin status field, select Enable. 5 Click Next. The AMCC Group – Select Members Parameters page opens. Page 186 of 825 Ceragon Proprietary and Confidential...
Figure 129: AMCC Group – Select Members Parameters Page (Hub Site) Figure 130: AMCC Group – Select Members Parameters Page (Tail Site) 6 In the Member #1 field, select a radio interface. Page 187 of 825 Ceragon Proprietary and Confidential...
Figure 131: AMCC Group – Selection Summary Page 11 Click Submit. The unit is automatically reset. Once AFR has been configured on the Hub site and both Tail sites, the configuration is complete. Page 188 of 825 Ceragon Proprietary and Confidential...
5 In the Advanced Multi Carrier Configuration page, select the group and click Delete. Once you have performed this procedure for the Hub site and both Tail sites, you can reconfigure the links according to the new network plan. Page 189 of 825 Ceragon Proprietary and Confidential...
2 Disable Multi-Carrier ABC, as described in Deleting a Multi-Carrier ABC Group. 3 Disable one of the two radio interfaces, as described in Enabling the Interfaces (Interface Manager). 4 Mute the disabled radio interface, as described in Configuring the Radio Parameters. Page 190 of 825 Ceragon Proprietary and Confidential...
The options are IPv4 or IPv6. To set the IP protocol version of the local unit: 1 Select Platform > Management > Networking > Local. The Local Networking Configuration page opens. Page 191 of 825 Ceragon Proprietary and Confidential...
Networking Configuration page opens. ◦ For multi-carrier units, the Radio Parameters page initially displays a table as shown in Figure 135. ◦ For single-carrier units, the page appears as shown in Figure 136. Page 192 of 825 Ceragon Proprietary and Confidential...
2 For multi-carrier units, select the carrier in the Radio table (see Figure 135) and click Edit. A separate Remote IP Configuration page opens. The page is identical to the single-carrier page. Page 193 of 825 Ceragon Proprietary and Confidential...
3 Set the Remote IP Address as desired, and the Remote Default Gateway as desired. Similarly, if you wish to change the Remote IPv6 Address to a different subnet: 1 Change the address of the Remote IPv6 Default Gateway to 0:0:0:0:0:0:0:0. 2 Click Apply. Page 194 of 825 Ceragon Proprietary and Confidential...
Each line in the Trap Managers table displays the setup for a manager defined in the system. To configure trap managers: 1 Select Platform > Management > SNMP > Trap Managers. The Trap Managers page opens. Page 197 of 825 Ceragon Proprietary and Confidential...
2 Select a trap manager and click Edit. The Trap Managers Edit page opens. Figure 142: Trap Managers - Edit Page 3 Configure the trap manager parameters, as described in Table 24. 4 Click Apply, then Close. Page 198 of 825 Ceragon Proprietary and Confidential...
V3 user defined in the system. To view or define a V3 user, use the V3 Users page. Note: Make sure that an identical V3 user is also defined on the manager's side. Page 199 of 825 Ceragon Proprietary and Confidential...
In the Add user account window, enter a user name and click OK. iv In the Users window, select Enable account and, optionally, select Password and enter a password. In the Users window, click OK. Figure 143: FileZilla Server User Configuration Page 200 of 825 Ceragon Proprietary and Confidential...
Click Set as home directory to make the Shared folder the root directory for your FTP server. viii Click OK to close the Users window. Figure 144: FileZilla Server Shared Folder Setup Page 201 of 825 Ceragon Proprietary and Confidential...
From any of these pages, click FTP Port. The FTP Port page opens. Figure 145: FTP Port Page Edit the File transfer port number for FTP and or SFTP and click Apply. Page 202 of 825 Ceragon Proprietary and Confidential...
Upon installation, this version will become the Installed Version. Reset Type The level of reset required by the component in order for the Installed Version to become the Active Version. A cold (hard) reset powers down and powers Page 203 of 825 Ceragon Proprietary and Confidential...
HTTP and HTTPS can only be used to download files for CeraOS 9.5 and later. If there is a requirement to downgrade from CeraOS 9.5 or higher to an earlier version using HTTP or HTTPS, contact Ceragon Customer Support for assistance.
4 Click Choose File. A browse window opens. 5 Navigate to the directory in which the software file is located and select the file. The selected file must be a ZIP file. Page 205 of 825 Ceragon Proprietary and Confidential...
3 Unzip the new software package for IP-20 into your shared FTP or SFTP folder. 4 In the IP-20’s Web EMS, select Platform > Software > Download & Install. The Download & Install page opens. Page 206 of 825 Ceragon Proprietary and Confidential...
7 In the File Transfer Protocol field, select the file transfer protocol you want to use (FTP or SFTP). 8 In the Username field, enter the user name you configured in the FTP server. Page 207 of 825 Ceragon Proprietary and Confidential...
Page 208
Upon completion of the installation, the system performs an automatic reset. Important Notes: • DO NOT reboot the unit during the software installation process. As soon as the process is successfully completed, the unit will reboot itself. Page 208 of 825 Ceragon Proprietary and Confidential...
Installation Success • Installation Partial Success • Installation Failure • incomplete-sw-version When the system is reset, the Installation Status returns to Ready. Install progress Displays the progress of the current software installation. Page 209 of 825 Ceragon Proprietary and Confidential...
For example, in Figure 152, the timer is set for two hours after the timer was configured (02:00). 7 Click Apply, then Close to close the Install Parameters page. Page 210 of 825 Ceragon Proprietary and Confidential...
For details, see Installing and Configuring an FTP or SFTP Server. Before importing or exporting a configuration file, you must perform the following steps: Page 212 of 825 Ceragon Proprietary and Confidential...
4 Click FTP Parameters to display the FTP Parameters page. Figure 155: FTP Parameters Page (Configuration Management) 5 In the Username field, enter the user name you configured in the FTP server. Page 213 of 825 Ceragon Proprietary and Confidential...
2 Select Platform > Configuration > Configuration Management. The Configuration Management page opens (Figure 154). 3 In the File Number field, select the restore point from which you want to export the file. Page 214 of 825 Ceragon Proprietary and Confidential...
The next time the system is reset, the File Transfer status field returns to Ready. After importing the configuration file, you can apply the configuration by restoring the file from the restore point to which you saved it. See Restoring a Saved Configuration. Page 215 of 825 Ceragon Proprietary and Confidential...
2 In the File Number field, select the restore point that holds the configuration you want to restore. 3 Click Restore. The configuration restoration begins. You can view the status of the restoration in the Configuration restore status field. Page 216 of 825 Ceragon Proprietary and Confidential...
If any specific command in the CLI script requires reset, the unit is reset when that command is executed. During initialization following the reset, execution of the CLI script continues from the following command. Page 217 of 825 Ceragon Proprietary and Confidential...
1 Select Platform > Shelf Management > Chassis Configuration. The Chassis Configuration page opens (Figure 156). 2 Click Reset. 3 A prompt appears asking if you want to proceed with the reset. Click Yes to initiate the reset. The unit is reset. Page 218 of 825 Ceragon Proprietary and Confidential...
The type of measurement you want the system to use: Metric or Imperial. format Unit The current temperature of the unit. If the unit temperature goes lower than - Temperature 40°C or higher than 90°C, the unit raises an extreme temperature alarm Page 219 of 825 Ceragon Proprietary and Confidential...
4 In the NTP server IP address field, enter the IP address of the NTP server. 5 Click Apply. Table 29 describes the status parameters that appear in the NTP Configuration page. Page 220 of 825 Ceragon Proprietary and Confidential...
To view the unit's part number and serial number: 1 Select Platform > Management > Inventory. The Inventory page opens, showing the unit's part number and serial number. Figure 159: Inventory Page Page 221 of 825 Ceragon Proprietary and Confidential...
They are only updated if the alarm is cleared, then raised again. If there is no signal on the interface, a Loss of Carrier alarm (LOC) is raised, and this alarm masks the DDM alarms. Figure 160: SFP Alarm Example Page 222 of 825 Ceragon Proprietary and Confidential...
Displays the vendor’s part number for the SFP module. Vendor Serial Number Displays the vendor’s serial number for the SFP module. Vendor Revision Displays the revision number of the serial number provided by the vendor for the SFP module. Page 223 of 825 Ceragon Proprietary and Confidential...
If the Admin status of the port is Down, the TX Power Level is displayed as -40 DBm and the Bias Current is displayed as 0 mA. The Temperature is always shown as long as the SFP module is inserted in the port. Page 224 of 825 Ceragon Proprietary and Confidential...
Configuring XPIC • Configuring Unit Protection with HSB Radio Protection (External Protection) • Configuring MIMO and Space Diversity Operating an IP-20C or IP-20C-HP in Single Radio Carrier Mode • • Performing Radio Loopback Page 225 of 825 Ceragon Proprietary and Confidential...
2 For multi-carrier units, select the carrier in the Radio table (see Figure 162) and click Edit. A separate Radio Parameters page opens. The page is essentially identical to the Single-carrier page, except for the addition of a Radio location parameter. Page 226 of 825 Ceragon Proprietary and Confidential...
User Guide for FibeAir® IP-20 All-Outdoor Products, CeraOS 10.5 Figure 163: Radio Parameters Page Per Carrier – IP-20C/IP-20C-HP Page 227 of 825 Ceragon Proprietary and Confidential...
MRMC script and determine the current interference level for each channel. This enables you to select the best channel in accordance with current interference levels. See Running the Frequency Scanner (IP-20V). Page 228 of 825 Ceragon Proprietary and Confidential...
2 For multi-carrier units, select the carrier in the Remote Radio table (see Figure 164) and click Edit. A separate Remote Radio Parameters page opens. The page is identical to the single-carrier page. Page 229 of 825 Ceragon Proprietary and Confidential...
Enter a unique identifier from 1 to 65535. Remote Tx Output Level The remote unit's Tx output level, if the remote unit has been configured to operate at a fixed Tx level (in dBm). Page 230 of 825 Ceragon Proprietary and Confidential...
For multi-carrier units, the Radio Parameters page initially displays a table as shown in Figure 167. ◦ For single-carrier units, a page appears, similar to Figure 168 (which shows an IP-20C/IP-20C-HP page). Page 231 of 825 Ceragon Proprietary and Confidential...
MRMC script, and RFU type. 6 In the ATPC Override Admin field, select Enable to enable ATPC override or Disable to disable ATPC override. You can only enable ATPC override if ATPC itself is enabled. Page 232 of 825 Ceragon Proprietary and Confidential...
Page 233
12 In the Remote Reference RX Level (dBm) field, enter a number between -70 and -30 as the reference value for the ATPC mechanism on the remote radio carrier. 13 Click Apply. To cancel an ATPC override state on the local unit, click Cancel Override. Page 233 of 825 Ceragon Proprietary and Confidential...
Figure 169. ◦ For IP-20S units, a page appears, similar to Figure 170 (which shows an IP- 20C/IP-20C-HP page). Figure 169: Radio Ethernet Interface Configuration Page – IP-20C/IP-20C-HP Page 234 of 825 Ceragon Proprietary and Confidential...
Tunnel-Layer4 – Header De-Duplication operates on Layer 2, Layer 3, and on the Tunnel, T-3, and T-4 layers for packets carrying GTP or GRE frames. 6 Click Apply, then Close Note: The Utilization threshold field is not applicable. Page 235 of 825 Ceragon Proprietary and Confidential...
For multi-carrier units, the Radio Ethernet Interface Configuration page initially displays a table as shown in Figure 171. ◦ For single-carrier units, the page appears as shown in Figure 172. Figure 171: Radio Ethernet Interface Counters Page – IP-20C/IP-20C-HP Page 236 of 825 Ceragon Proprietary and Confidential...
2 For multi-carrier units, select the carrier in the Header Compression Counters table (Figure 171) and click View. A separate Radio Ethernet Interface Configuration page opens. The page is essentially identical to the single-carrier page. Page 237 of 825 Ceragon Proprietary and Confidential...
Bytes on the TX side that were compressed by Header De-Duplication. bytes TX frames before Frames on the TX side before Header De-Duplication. enhanced HC TX frames Frames on the TX side that were compressed by Header De-Duplication. compressed by enhanced HC Page 238 of 825 Ceragon Proprietary and Confidential...
Page 239
The number of idle bytes transmitted since the last time the Radio Ethernet Interface counters were cleared. Cut Through Counters TX frames The number of frames that have been transmitted via Frame Cut-Through since the last time the Radio Ethernet Interface counters were cleared. Page 239 of 825 Ceragon Proprietary and Confidential...
For multi-carrier units, the Payload Encryption page initially displays a table as shown in Figure 174. ◦ For IP-20S units, a page appears, similar to Figure 175 (which shows an IP- 20C/IP-20C-HP page). Page 240 of 825 Ceragon Proprietary and Confidential...
6 Configure the master key by doing one of the following: ◦ Enter a master key in the Master Key field. You must enter between 8 and 32 ASCII characters. ◦ Click Generate key to generate a master key automatically. Page 241 of 825 Ceragon Proprietary and Confidential...
This step will cause the link status to be Down until payload encryption is successfully enabled on the local unit. However, the RSL measured on the link should remain at an acceptable level. Page 242 of 825 Ceragon Proprietary and Confidential...
Page 243
See Disabling Automatic Switchover to the Standby Unit. 13 Verify that there are no alarms on the link. Note: Any time payload encryption fails, the Operational status of the link is Down until payload encryption is successfully restored. Page 243 of 825 Ceragon Proprietary and Confidential...
MSE PM thresholds are configured from the MSE PM Report page. See Displaying MSE PMs and Configuring MSE PM Thresholds. • XPI PM thresholds are configured from the XPI PM Report page. See Displaying XPI PMs and Configuring XPI PM Thresholds. Page 244 of 825 Ceragon Proprietary and Confidential...
Excessive BER administration is enabled or disabled for the entire unit rather than for specific radios. 3 In the Thresholds table, select the radio for which you want to configure thresholds. Page 245 of 825 Ceragon Proprietary and Confidential...
Configuring the Radio (MRMC) Script(s) To display the current modulation and bit rate per radio: 1 Select Radio > MRMC > MRMC Status. The MRMC Status page opens. Figure 179: MRMC Status Page Page 246 of 825 Ceragon Proprietary and Confidential...
To display Multi-Rate Multi-Constellation PMs, including information on ACM profile fluctuations per interval per radio: 1 Select Radio > PM & Statistics > MRMC. The MRMC PM Report page opens. Figure 180: MRMC PM Report Page Page 247 of 825 Ceragon Proprietary and Confidential...
1 Select Radio > PM & Statistics > Counters. The Counters page opens. ◦ For multi-carrier units, the Counters page initially displays a table as shown in Figure 181. ◦ For single-carrier units, the Counters page appears as shown in Figure 182. Page 248 of 825 Ceragon Proprietary and Confidential...
Table 37 describes the Signal Level PMs. Note: To display the same parameters for a specific interval in a separate page, select the interval in the RF PM table and click View. Page 250 of 825 Ceragon Proprietary and Confidential...
To set the Signal Level PM thresholds, click Thresholds. The Signal Level Thresholds Configuration – Edit Page opens. Set the thresholds, described in Table 38, and click Apply. Figure 185: Signal Level Thresholds Configuration – Edit Page Page 251 of 825 Ceragon Proprietary and Confidential...
Table 39 describes the Modem BER (Aggregate) PMs. Note: To display the same parameters for a specific interval in a separate page, select the interval in the Modem BER PM table and click View. Page 252 of 825 Ceragon Proprietary and Confidential...
2 For the IP-20C and IP-20C-HP, in the Interface field, select the radio for which you want to display PMs. 3 In the Interval Type field: ◦ To display reports in 15-minute intervals, select 15 minutes. Page 253 of 825 Ceragon Proprietary and Confidential...
Min XPI (dB) The minimum XPI level that was measured during the interval. Max XPI (dB) The maximum XPI level that was measured during the interval. Page 255 of 825 Ceragon Proprietary and Confidential...
To set the XPI PM thresholds, click Thresholds. The XPI Thresholds Configuration– Edit Page opens. For each radio, specify the modem XPI threshold for calculating XPI Exceed Threshold seconds, and click Apply. Figure 190: XPI Thresholds Configuration – Edit Page Page 256 of 825 Ceragon Proprietary and Confidential...
PM mechanism divides the total number of bytes received during the 15-minute interval by 900. To display capacity and throughput PMs per radio: 1 Select Radio > PM & Statistics > Traffic > Capacity/Throughput. The Capacity PM report page opens. Page 257 of 825 Ceragon Proprietary and Confidential...
Figure 192: Ethernet Radio Capacity and Throughput Threshold Page 2 Enter the capacity and throughput thresholds you want, in Mbps. The range of values is 0 to 4294967295. The default value for is 1000. 3 Click Apply, then Close. Page 258 of 825 Ceragon Proprietary and Confidential...
◦ To display reports in daily intervals, select 24 hours. To set the thresholds for utilization PMs: 1 Select Threshold. The Utilization Threshold page opens. Figure 194: Ethernet Radio Utilization Threshold Page Page 260 of 825 Ceragon Proprietary and Confidential...
Indicates whether the values received at the time and date of the measured interval are reliable. An x in the column indicates that the values are not reliable due to a possible power surge or power failure that occurred at that time. Page 262 of 825 Ceragon Proprietary and Confidential...
Configuring In- Band Management. A service point is a logical entity attached to a physical or logical interface. Service points define the movement of frames through the service. Each service point Page 263 of 825 Ceragon Proprietary and Confidential...
The Ethernet Services page is the starting point for defining Ethernet services on the IP-20. To open the Ethernet Services page: 1 Select Ethernet > Services. The Ethernet Services page opens. Figure 196: Ethernet Services Page Page 264 of 825 Ceragon Proprietary and Confidential...
To add an Ethernet service: 1 Select Ethernet > Services. The Ethernet Services page opens (Figure 196). 2 In the Ethernet Services page, click Add. The Ethernet Services – Add page opens. Page 265 of 825 Ceragon Proprietary and Confidential...
You can select a value from 16 to 131,072, in multiples of 16. This maximum only applies to dynamic, not static, MAC address table entries. Page 266 of 825 Ceragon Proprietary and Confidential...
1 Select Ethernet > Services. The Ethernet Services page opens (Figure 196). 2 Select the services in the Ethernet Services Configuration table, or select all the services by selecting the check box in the top row. Page 267 of 825 Ceragon Proprietary and Confidential...
3 In the Ethernet Services page, click Service Details. The Ethernet Services – Service Details page opens. The Service Details page contains the same fields as the Add page (Figure 197). However, in the Service Details page, these fields are read-only. Page 268 of 825 Ceragon Proprietary and Confidential...
1 Select Ethernet > Services. The Ethernet Services page opens (Figure 196). 2 Select the relevant service in the Ethernet Services Configuration table. 3 Click Service Points. The Ethernet Service Points page opens. Page 269 of 825 Ceragon Proprietary and Confidential...
Service Points – Add page. Once you have added the service point, you cannot change the service point ID. Service point name A descriptive name for the service point (optional). The Service Point Name can be up to 20 characters. Page 270 of 825 Ceragon Proprietary and Confidential...
Page 271
If you selected Bundle-S in the Attached Interface Type field, select the S- VLAN value to classify into the service point (1-4094), or select Untagged. You can then add multiple C-VLANs via the Attach VLAN option. See Attaching VLANs. Page 271 of 825 Ceragon Proprietary and Confidential...
Select Ingress in the Ethernet Service Points page to display the Ethernet Service Points – Ingress Attributes table. Table 48 describes the parameters displayed in the Ingress SP Attributes table. Figure 200: Ethernet Service Points Page – Ingress Attributes Page 272 of 825 Ceragon Proprietary and Confidential...
Ethernet Service Points – Egress Attributes Select Egress in the Ethernet Service Points page to display the Ethernet Service Points – Egress Attributes table. Table 49 `describes the parameters displayed in the General SP Attributes table. Page 273 of 825 Ceragon Proprietary and Confidential...
If C-VLAN preservation is disabled, the C-VLAN ID of frames egressing the service point is set at whatever value might have been re-assigned by the interface, service point, or service, or whatever value results from marking (see Marking admin, below). Page 274 of 825 Ceragon Proprietary and Confidential...
Page 275
1 Select Ethernet > Services. The Ethernet Services page opens (Figure 196). 2 Select the relevant service in the Ethernet Services Configuration table. 3 Click Service Points. The Ethernet Service Points page opens (Figure 199). Page 275 of 825 Ceragon Proprietary and Confidential...
5 Click Add. The Ethernet Service Points – Add page opens. Figure 202: Ethernet Service Points - Add Page 6 Configure the service point attributes, as described in Table 46, Table 48, and Table 49. Page 276 of 825 Ceragon Proprietary and Confidential...
Page 277
Bundle-S, you can add multiple C-VLANs to the service point. To add multiple C-VLANs: 1 Select Ethernet > Services. The Ethernet Services page opens (Figure 196). 2 Select the relevant service in the Ethernet Services Configuration table. Page 277 of 825 Ceragon Proprietary and Confidential...
Figure 203: Attached VLAN List Page 6 Click Add. The Attached VLAN List - Add page opens. Figure 204: Attached VLAN List - Add Page 7 Configure the VLAN Classification parameters, described in Table 50. Page 278 of 825 Ceragon Proprietary and Confidential...
Classification table and click Edit. You can edit all the fields that can be configured in the Attached VLAN List – Add page. To delete a VLAN Classification table entry, select the entry in the VLAN Classification table and click Delete. Page 279 of 825 Ceragon Proprietary and Confidential...
S-VLAN ethertype. Options are: 0x8100, 0x88A8, 0x9100, and 0x9200. The default value is 0x88A8. Note: The C-VLAN Ethertype is set at 0x8100 and cannot be modified. 4 Click Apply. Page 280 of 825 Ceragon Proprietary and Confidential...
IP-20E unit to 2.5 Gbps. After changing the speed of an SFP+ interface, you must reset the unit in order for the change to take effect. Page 282 of 825 Ceragon Proprietary and Confidential...
Actual port duplex Displays the actual duplex status of the interface for the link as agreed by the two sides of the link after the auto negotiation process. Page 283 of 825 Ceragon Proprietary and Confidential...
Even when no triggering event has taken place, the ASP mechanism sends periodic update messages indicating that no triggering event has taken place. Page 284 of 825 Ceragon Proprietary and Confidential...
2 Click Add. The Automatic State Propagation - Add page opens. Figure 209: Automatic State Propagation - Add Page 3 In the Controlled Ethernet interface field, select an interface that will be disabled upon failure of the Monitored Radio Interface, defined below. Page 285 of 825 Ceragon Proprietary and Confidential...
Page 286
1 Select the interface pair in the Automatic state propagation configuration table. 2 Click Delete. The interface pair is removed from the Automatic state propagation configuration table. To delete multiple interface pairs: Page 286 of 825 Ceragon Proprietary and Confidential...
Page 287
1 Select the interface pairs in the Automatic state propagation configuration table or select all the interfaces by selecting the check box in the top row. 2 Click Delete. The interface pairs are removed from the Automatic state propagation configuration table. Page 287 of 825 Ceragon Proprietary and Confidential...
1 In the header row, select the arrow next to any of the columns. 2 Select Columns. 3 Mark the interfaces you want to display and clear the interfaces you do not want to display. Page 288 of 825 Ceragon Proprietary and Confidential...
1 Select Ethernet > PM & Statistics > Egress CoS Statistics. The Egress CoS Statistics page opens. Figure 212: Egress CoS Statistics Page 2 In the Show Service bundle ID field, select 1. Page 289 of 825 Ceragon Proprietary and Confidential...
Figure 213: Egress CoS Statistics – Edit Page 2 In the Clear on read field, select Yes to have statistics for the CoS value cleared every time you open the page. 3 Click Apply. Page 290 of 825 Ceragon Proprietary and Confidential...
Peak... Average... bytes... Various peak transmission rates (per second) and average transmission Packets... rates (per second), both in bytes and in packets, for each measured time interval. Page 291 of 825 Ceragon Proprietary and Confidential...
TX bytes exceeded the specified threshold during the interval: To view and set this threshold: 1 In the Ethernet Port TX PM Report page, click Threshold. The Ethernet Port Tx Threshold page opens. Page 292 of 825 Ceragon Proprietary and Confidential...
1 Select Ethernet > PM & Statistics > Port RX. The Ethernet Port RX PM Report page opens. Figure 217: Ethernet Port RX PM Report Page 2 In the Interface field, select the interface for which you want to display PMs. 3 In the Interval Type field: Page 293 of 825 Ceragon Proprietary and Confidential...
To select the interfaces for which to gather and display Port RX PMs: 1 In the Ethernet Port RX PM Report page, click PM Admin. The Ethernet PM Port Admin page opens. Figure 218: Ethernet PM Port Admin Page 2 Select the interface. Page 294 of 825 Ceragon Proprietary and Confidential...
1 In the Ethernet Port RX PM Report page, click Threshold. The Ethernet Port Rx Threshold page opens. Figure 219: Ethernet Port Rx Threshold Page 2 Enter a threshold, between 0 and 4294967295. 3 Click Apply, then Close. Page 295 of 825 Ceragon Proprietary and Confidential...
(Optional) Rate Limit GE/Radio Classifier Port (Policing) Queue Scheduler/ GE/Radio Port Manager Shaper (Optional) Standard QoS/ H-QoS Figure 220: QoS Block Diagram The ingress path consists of the following QoS building blocks: Page 296 of 825 Ceragon Proprietary and Confidential...
Page 297
Marker – This mechanism provides the ability to modify priority bits in frames based on the calculated CoS and Color. For a more detailed description of QoS in the IP-20, refer to the Technical Description for the IP-20 product type you are using. Page 297 of 825 Ceragon Proprietary and Confidential...
Classification is performed step by step from the highest priority to the lowest priority classification method. Once a match is found, the classifier determines the CoS and Color decision for the frame for the logical interface-level. Page 298 of 825 Ceragon Proprietary and Confidential...
MPLS classification, so that if a match is found with the DSCP value of the ingressing frame, MPLS bits are not considered. • Un-Trust – The interface does not consider DSCP during classification. Page 300 of 825 Ceragon Proprietary and Confidential...
Description – Read-only. The description of the DSCP value. ◦ CoS – The CoS assigned to frames with the designated DSCP value. ◦ Color – The Color assigned to frames with the designated DSCP value. 4 Click Apply, then Close. Page 304 of 825 Ceragon Proprietary and Confidential...
CoS – The CoS assigned to frames with the designated MPLS EXP value. ◦ Color – The Color assigned to frames with the designated MPLS EXP value. 4 Click Apply, then Close. Page 306 of 825 Ceragon Proprietary and Confidential...
7.3.2 Configuring Policer Profiles This section includes: • Adding a Policer Profile Editing a Policer Profile • Deleting a Policer Profile • Page 307 of 825 Ceragon Proprietary and Confidential...
2 Click Add. The Policer Profile - Add page opens. Figure 232: Policer Profile - Add Page 3 Configure the profile’s parameters. See Table 55 for a description of the policer profile parameters. 4 Click Apply, then Close. Page 308 of 825 Ceragon Proprietary and Confidential...
See Assigning Policers to Interfaces. To delete a policer profile, select the profile in the Police Profile table and click Delete. The profile is deleted. To delete multiple policer profiles: Page 309 of 825 Ceragon Proprietary and Confidential...
(Figure 221). 2 Select the interface in the Ethernet Logical Port Configuration Table and click Policers. The Policers page opens. By default, the Policers page opens to the Unicast Policer table (Figure 233). Page 310 of 825 Ceragon Proprietary and Confidential...
5 In the Multicast admin field, select Enable to enable policing on multicast traffic flows from the logical interface, or Disable to disable policing on multicast traffic flows from the logical interface. 6 Click Apply. Page 311 of 825 Ceragon Proprietary and Confidential...
You can define up to three policers per Ethertype value. To assign a policer to an Ethertype: 1 Select Ethernet > Interfaces > Logical Interfaces. The Logical Interfaces page opens (Figure 221). Page 312 of 825 Ceragon Proprietary and Confidential...
Layer 1 non-effective traffic bytes. To define the ingress byte compensation value for a logical interface: 1 Select Ethernet > Interfaces > Logical Interfaces. The Logical Interfaces page opens (Figure 221). Page 313 of 825 Ceragon Proprietary and Confidential...
CoS and color, and the mapping table for C-VLAN or S- VLAN. 7.4.2 Enabling Marking Marking is enabled and disabled on the service point level. See Ethernet Service Points – Egress Attributes. Page 314 of 825 Ceragon Proprietary and Confidential...
2 Select the row you want to modify and click Edit. The 802.1Q Marking - Edit page opens. Figure 238: 802.1Q Marking - Edit Page 3 Enter the new 802.1Q UP and 802.1Q CFI values. Page 315 of 825 Ceragon Proprietary and Confidential...
2 Select the row you want to modify and click Edit. The 802.1AD Marking - Edit page opens. Figure 240: 802.1AD Marking - Edit Page 3 Enter the new 802.1AD UP and 802.1AD DEI values. Page 316 of 825 Ceragon Proprietary and Confidential...
Page 317
User Guide for FibeAir® IP-20 All-Outdoor Products, CeraOS 10.5 4 Click Apply, then Close. Page 317 of 825 Ceragon Proprietary and Confidential...
TCP flows will be restrained before traffic congestion occurs. 7.5.2 Configuring WRED Profiles This section includes: Adding a WRED Profile • • Editing a WRED Profile • Deleting a WRED Profile Page 318 of 825 Ceragon Proprietary and Confidential...
5 In the Green curve max point field, enter the maximum throughput of green packets for queues with this profile, in Kbytes (0-8192). When this value is reached, all green packets in the queue are dropped. Page 319 of 825 Ceragon Proprietary and Confidential...
Page 320
To delete multiple WRED profiles: 1 Select the profiles in the WRED Profile Configuration table or select all the profiles by selecting the check box in the top row. 2 Click Delete. The profiles are deleted. Page 320 of 825 Ceragon Proprietary and Confidential...
Figure 244: Logical Interfaces – WRED - Edit Page 5 In the Profile ID field, select the WRED profile you want to assign to the selected queue. 6 Click Apply, then Close. Page 321 of 825 Ceragon Proprietary and Confidential...
Egress shaping on the interface level is planned for future release. 7.6.2 Configuring Queue Shaper Profiles This section includes: • Adding a Queue Shaper Profile Editing a Queue Shaper Profile • • Deleting a Queue Shaper Profile Page 322 of 825 Ceragon Proprietary and Confidential...
5 In the CIR field, enter the Committed Information Rate (CIR) assigned to the profile, in bits per second. Permitted values are: ◦ 16,000 - 32,000,000 bps, with granularity of 16,000. ◦ 32,000,000 - 131,008,000 bps, with granularity of 64,000. 6 Click Apply, then Close. Page 323 of 825 Ceragon Proprietary and Confidential...
7.6.3.1 Adding a Service Bundle Shaper Profile To add a service bundle shaper profile: 1 Select Ethernet > QoS > Shaper > Service Bundle Profiles. The Service Bundle Shaper Profile page opens. Page 324 of 825 Ceragon Proprietary and Confidential...
6 In the PIR field, enter the Peak Information Rate (PIR) assigned to the profile, in bits per second. Permitted values are: ◦ 16,000 – 32,000,000 bps, with granularity of 16,000. ◦ 32,000,000 – 1,000,000,000 bps, with granularity of 64,000. 7 Click Apply, then Close. Page 325 of 825 Ceragon Proprietary and Confidential...
2 Select an interface in the Ethernet Logical Port Configuration table and click Shaper. The Logical Interfaces – Shaper page opens, with the Egress Queue Shaper Configuration table open by default. All queue shaper profiles defined in the system are listed in the table. Page 326 of 825 Ceragon Proprietary and Confidential...
6 In the Shaper Admin field, select Enable to enable egress queue shaping for the selected queue, or Disable to disable egress queue shaping for the selected queue. 7 Click Apply, then Close. Page 327 of 825 Ceragon Proprietary and Confidential...
3 Select Egress Service Bundle Shaper. The Egress Service Bundle Shaper Configuration table appears. All service bundle shaper profiles defined in the system are listed in the table. Figure 251: Logical Interfaces – Shaper – Egress Service Bundle Shaper Page 328 of 825 Ceragon Proprietary and Confidential...
6 To enable or disable egress service bundle shaping, select Enable or Disable. 7 Click Apply, then Close. Configuring Scheduling This section includes: • Scheduling Overview • Configuring Priority Profiles Configuring WFQ Profiles • Assigning a Priority Profile to an Interface • Page 329 of 825 Ceragon Proprietary and Confidential...
User Guide for FibeAir® IP-20 All-Outdoor Products, CeraOS 10.5 Figure 254: Scheduler Priority Profile – Add Page 3 In the Profile ID field, select a unique Profile ID between 1 and 8. Page 332 of 825 Ceragon Proprietary and Confidential...
You can configure up to five WFQ profiles. A sixth profile, Profile ID 1, is pre-configured. This section includes: • Adding a WFQ Profile Editing a WFQ Priority Profile • Deleting a WFQ Profile • Page 333 of 825 Ceragon Proprietary and Confidential...
3 In the Profile ID field, select a unique Profile ID between 2 and 7. Profile ID 1 is used for a pre-defined WFQ profile. 4 For each CoS value, enter the weight for that CoS, from 1 to 20. Page 334 of 825 Ceragon Proprietary and Confidential...
2 Select an interface in the Ethernet Logical Port Configuration table and click Scheduler. The Logical Interfaces – Scheduler page opens, with the Egress Port Scheduling Priority Configuration – Edit page open by default. Page 335 of 825 Ceragon Proprietary and Confidential...
Scheduler. The Logical Interfaces – Scheduler page opens, with the Egress Port Scheduling Priority Configuration – Edit page open by default (Figure 257). 3 Select Egress Port Scheduling WFQ. The Egress Port Scheduling WFQ Configuration – Edit page opens. Page 336 of 825 Ceragon Proprietary and Confidential...
Figure 258: Logical Interfaces – Scheduler – Egress Port Scheduling WFQ 4 In the Profile ID field, select from a list of configured scheduling priority profiles. See Configuring WFQ Profiles. 5 Click Apply, then Close. Page 337 of 825 Ceragon Proprietary and Confidential...
When bandwidth degrades from the nominal value in the Monitored Interface, messages relaying the actual bandwidth values are periodically sent over the Control Interface. A termination message is sent once the bandwidth returns to its nominal level. Page 338 of 825 Ceragon Proprietary and Confidential...
5 In the Admin field, select Up to enable ABN monitoring or Down to disable ABN monitoring. 6 In the Monitored Interface field, select the Monitored Interface. This is the interface which is constantly monitored for its bandwidth value. Page 339 of 825 Ceragon Proprietary and Confidential...
Nominal BW, the Current BW, and the Version. 4 Edit the ABN entity attributes, as described in Adding an ABN entity. 5 Click Apply, then Close. Page 340 of 825 Ceragon Proprietary and Confidential...
• On – Holdoff measurement time has ended and the current bandwidth is still below the nominal value. Holdoff Start Time (mSec) The Holdoff start time for the last event. Page 341 of 825 Ceragon Proprietary and Confidential...
To display a summary of the important LLDP management information regarding the unit's nearest neighbor (peer): 1 Select Ethernet > Protocols > LLDP > Remote Management. The LLDP Remote Management page opens. Page 342 of 825 Ceragon Proprietary and Confidential...
IP Protocol Version for Initiating Communications. To display and configure the general LLDP parameters for the unit: 1 Select Ethernet > Protocols > LLDP > Advanced > Configuration > Parameters. The LLDP Configuration Parameters page opens. Page 343 of 825 Ceragon Proprietary and Confidential...
Admin status becomes Disabled until it will process a request to reinitialize LLDP. For instructions on disabling or enabling LLDP on a port, see Configuring the LLDP Port Parameters. In this release, the Reinit Delay is set at 2. Page 344 of 825 Ceragon Proprietary and Confidential...
1 Select Ethernet > Protocols > LLDP > Advanced > Configuration > Port Configuration. The LLDP Port Configuration page opens. Figure 264: LLDP Port Configuration Page 2 Select an interface and click Edit. The LLDP Port Configuration - Edit page opens. Page 345 of 825 Ceragon Proprietary and Confidential...
PortDesc – The LLDP agent transmits Port Description TLVs. • SysName – The LLDP agent transmits System Name TLVs. • SysDesc – The LLDP agent transmits System Description TLVs. • SysCap – The LLDP agent transmits System Capabilities TLVs. Page 346 of 825 Ceragon Proprietary and Confidential...
To displays the MAC address associated with the unit for purposes of LLDP transmissions: 1 Select Ethernet > Protocols > LLDP > Advanced > Configuration > Management TLV. The LLDP Management TLV Configuration page opens. Page 347 of 825 Ceragon Proprietary and Confidential...
Defines the type of the management address identifier encoding used for the Management Address. Tx Enable Indicates whether the unit's Management Address is transmitted with LLDPDUs. In this release, the Management Address is always sent. Page 348 of 825 Ceragon Proprietary and Confidential...
Remote ID An arbitrary local integer value used by this agent to identify a particular connection instance, unique only for the indicated remote system. Time Mark The time the entry was created. Page 349 of 825 Ceragon Proprietary and Confidential...
An octet string used to identify the port component associated with the remote system. Port Sub type The type of port identifier encoding used in the peer's Port ID. Time Mark The time the entry was created. Page 350 of 825 Ceragon Proprietary and Confidential...
Chassis ID The MAC Address of the local unit. Chassis ID SubType The type of encoding used to identify the local unit. In this release, this parameter is always set to MAC Address. Page 351 of 825 Ceragon Proprietary and Confidential...
Port Sub Type The type of encoding used to identify the port in LLDP transmissions. In this release, this parameter is always set to MAC Address. Port Description A description of the port. Page 353 of 825 Ceragon Proprietary and Confidential...
2 To display all the parameters, select a row and click View. Figure 273: LLDP Local System Management – View Page Table 67 describes the parameters in the LLDP Local System Management page. These parameters are read-only. Page 354 of 825 Ceragon Proprietary and Confidential...
1 Select Ethernet > Protocols > LLDP > Advanced > Statistic > Port TX. The LLDP Port TX Statistic page opens. Figure 275: LLDP Port TX Statistics Page Table 69 describes the statistics in the LLDP Port TX Statistic page. Page 356 of 825 Ceragon Proprietary and Confidential...
Table 70 describes the statistics in the LLDP Port TX Statistic page. Table 70: LLDP Port RX Statistics Parameter Definition Interface Location The index value used to identify the port in LLDP transmissions. Destination Address The LLDP MAC address associated with this entry. Page 357 of 825 Ceragon Proprietary and Confidential...
Page 358
This counter is set to zero during agent initialization. This counter is incremented only once when the complete set of information is invalidated (aged out) from all related tables on a particular port. Partial ageing is not allowed. Page 358 of 825 Ceragon Proprietary and Confidential...
By default, the Sync mode is set to Automatic. To display the current Sync mode, enter the following command in root view: root> platform sync mode show 2 In the Web EMS, select Sync > SyncE Regenerator. The SyncE Regenerator page opens. Page 359 of 825 Ceragon Proprietary and Confidential...
Ethernet interface. If the two interfaces are the same type, the operation will fail. Only one radio port is available for IP-20S, IP-20E, and IP-20V units. 6 Click Apply. Page 360 of 825 Ceragon Proprietary and Confidential...
When configuring an Ethernet interface as a Sync source, the Media Type of the interface must be RJ45 or SFP, not Auto-Type. To view and configure the Media Type of an Ethernet interface, see Configuring Ethernet Interfaces. Page 361 of 825 Ceragon Proprietary and Confidential...
SSM messages. For instructions how to enable SSM, see Configuring the Outgoing Clock and SSM Messages. Sync Interface Displays the priority assigned to this synchronization source. Priority Sync Interface Displays the current actual synchronization quality of the interface. Quality Status Page 362 of 825 Ceragon Proprietary and Confidential...
You cannot assign the same priority to more than one synchronization source. Once a priority value has been assigned, it no longer appears in the Sync Interface Priority dropdown list. 5 Click Apply, then Close. Page 363 of 825 Ceragon Proprietary and Confidential...
In order to prevent loops, an SSM with quality “Do Not Use” is sent from the active source interface (both radio and Ethernet) In order for an interface to transmit SSM messages, SSM must be enabled on the interface. By default, SSM is disabled on all interfaces. Page 364 of 825 Ceragon Proprietary and Confidential...
Figure 282: Outgoing Clock – Edit Page 3 In the Outgoing clock source field, select the interface's synchronization source. Options are: ◦ Local Clock – The interface uses its internal clock as its synchronization source. Page 365 of 825 Ceragon Proprietary and Confidential...
Page 366
4 In Sync Radio Channel field, use the default value of 0. 5 In the SSM Admin field, select On or Off to enable or disable SSM for the interface. By default, SSM is disabled on all interfaces. Page 366 of 825 Ceragon Proprietary and Confidential...
Sync source, with lower priority than the radio interface. See Adding a Sync Source. 5 Verify that the Sync Interface Quality Status of the first Sync source is not Failure. See Viewing the Sync Source Status. Page 367 of 825 Ceragon Proprietary and Confidential...
2 In the 1588 PTP field, select Disable. 3 Click Apply. Note: Disabling 1588 PTP disables both Transparent Clock and Boundary Clock, and can drastically affect time synchronization performance in the entire network. Page 369 of 825 Ceragon Proprietary and Confidential...
Another security feature, HTTPS cipher hardening, can be configured via CLI. For instructions, see Configuring HTTPS Cipher Hardening (CLI). Related topics: • Changing Your Password • Operating in FIPS Mode Configuring AES-256 Payload Encryption • Page 370 of 825 Ceragon Proprietary and Confidential...
0, or 30-90. If you enter 0, this feature is disabled. The default value is 0. 5 Click Apply. Once a user is blocked, you can unblock the user from the User Accounts page. To unblock a user: Page 371 of 825 Ceragon Proprietary and Confidential...
2 Select the user and click Edit. The Access Control User Accounts - Edit page opens. Figure 287: Access Control User Accounts - Edit Page 3 In the Blocked field, select No. 4 Click Apply, then Close. Page 372 of 825 Ceragon Proprietary and Confidential...
You can enter 20-90, or No Aging. If you select No Aging, password aging is disabled and passwords remain valid indefinitely. 5 Click Apply. Page 373 of 825 Ceragon Proprietary and Confidential...
1 Select Platform > Security > Protocols Control. The Protocols Control page opens. Figure 289: Protocols Control Page 2 In the Session timeout (Minutes) field, select a session timeout, in minutes, from 1 to 60. 3 Click Apply. Page 374 of 825 Ceragon Proprietary and Confidential...
The system includes a number of pre-defined user profiles. You can edit these profiles, and add user profiles. Together, the system supports up to 50 user profiles. Page 375 of 825 Ceragon Proprietary and Confidential...
1 Select Platform > Security > Access Control > User Profiles. The Access Control User Profiles page opens. Figure 290: Access Control User Profiles Page 2 Click Add. The Access Control User Profiles - Add page opens. Page 376 of 825 Ceragon Proprietary and Confidential...
To edit a user profile, select the profile and click Edit. You can edit all of the profile parameters except the profile name. To delete a user profile, select the profile and click Delete. Note: You cannot delete a user profile if the profile is assigned to any users. Page 377 of 825 Ceragon Proprietary and Confidential...
2 Click Add. The Access Control User Profiles - Add page opens. Figure 293: Access Control User Accounts - Add Page 3 In the User name field, enter a user name for the user. The user name can be up to 32 characters. Page 378 of 825 Ceragon Proprietary and Confidential...
To delete a user, select the user and click Delete. 10.5 Configuring RADIUS This section includes: • RADIUS Overview • Activating RADIUS Authentication Configuring the RADIUS Server Attributes • • Viewing RADIUS User Permissions and Connectivity • Configuring a RADIUS Server Page 379 of 825 Ceragon Proprietary and Confidential...
Connectivity Status – The connectivity status of the Radius server in the last • attempted connection: ◦ True – The last connection attempt succeeded. ◦ False – The last connection attempt failed. Page 381 of 825 Ceragon Proprietary and Confidential...
The User Instances column displays the number of open sessions the user • currently has. To view the user’s authorized access levels, click + next to the user name. The page refreshes and displays the additional access level information. Page 382 of 825 Ceragon Proprietary and Confidential...
1 Create three user groups, as follows: In the Server Manager, navigate to Configuration > Local Users and Groups. Right click Groups and create the following three user groups: ◦ Radius_Advanced ◦ Radius_Normal ◦ Radius_Viewer Page 383 of 825 Ceragon Proprietary and Confidential...
User Guide for FibeAir® IP-20 All-Outdoor Products, CeraOS 10.5 Figure 298: Server Manager – Creating User Groups 2 Create three users: ◦ ◦ ◦ Page 384 of 825 Ceragon Proprietary and Confidential...
1 In the Server Manager, navigate to Roles > Network Policy and Access Services > NPS (Local) > RADIUS Clients and Servers > RADIUS Clients. 2 Right-click RADIUS Clients, and select New RADIUS Client. The New RADIUS Client window appears. Page 385 of 825 Ceragon Proprietary and Confidential...
Confirm shared secret. Note down the secret because you will need to enter the same value in the Secret field of the Radius Configuration – Edit page (Figure 295). Page 386 of 825 Ceragon Proprietary and Confidential...
Figure 301: Create Network Policy – Specify Name and Connection Type 4 Click Next. 5 In the Specify Conditions window, click Add. 6 In the Select Condition window that appears, select the User Groups condition and click Add. Page 387 of 825 Ceragon Proprietary and Confidential...
8 In the Select Group window that appears, click Advanced. 9 In the Select Group window that appears, click Find Now to list all groups, and then select the appropriate group from the list: Radius_Advanced, Radius_Normal, or Radius_Viewer. 10 Click OK. Page 388 of 825 Ceragon Proprietary and Confidential...
Figure 303: Create Network Policy – User Group added to Policy’s Conditions 11 Click OK to save settings. 12 Click Next. 13 In the Specify Access Permission window that appears, select the Access Granted option. Page 389 of 825 Ceragon Proprietary and Confidential...
Figure 304: Create Network Policy – Specifying Access Permission 14 Click Next. 15 In the Configure Authentication Methods window that appears, make sure only the Unencrypted Authentication (PAP, SPAP) option is selected. Page 390 of 825 Ceragon Proprietary and Confidential...
User Guide for FibeAir® IP-20 All-Outdoor Products, CeraOS 10.5 Figure 307: Create Network Policy – Configuring Constraints 18 In the Configure Settings window that appears: Remove all Standard RADIUS attributes. Make sure the Attributes table is empty. Page 392 of 825 Ceragon Proprietary and Confidential...
Select the Vendor Specific checkbox and click Add under the Attributes table. 19 In the Add Vendor Specific Attribute window that appears: Select Custom in the Vendor drop down field. Click Add. Page 393 of 825 Ceragon Proprietary and Confidential...
User Guide for FibeAir® IP-20 All-Outdoor Products, CeraOS 10.5 Figure 309: Create Network Policy – Adding Vendor Specific Attributes 20 In the Attribute Information window that appears, click Add. Figure 310: Create Network Policy – Selecting to Add Attribute Information Page 394 of 825 Ceragon Proprietary and Confidential...
Thus for example, enter 2 for all twelve attributes if you are configuring a policy for the Radius_Advanced group. This gives Advanced read permissions and Advanced write permissions, for all six functional groups, to the members of the Radius_Advanced group. Page 395 of 825 Ceragon Proprietary and Confidential...
Thus for example, enter 127 to allow access from all channels: Serial + Telnet + SSH + Web + NMS + SNMP +SNMPv3; Or enter 24 to allow access only from NMS + SNMP channels. iii Click OK. Page 396 of 825 Ceragon Proprietary and Confidential...
26 Reset the Network Policy Server (NPS) by stopping and starting the NPS service as follows: Right click the NPS (Local) node, and select Stop NPS Service. Right click the NPS (Local) node, and select Start NPS Service. Page 397 of 825 Ceragon Proprietary and Confidential...
1 Add the users in the file, using any editor you like, /etc/raddb/users according to the following example: # user1 - advanced privileges auth-type := local, Cleartext-Password := "1111" security-ro = advanced, Page 398 of 825 Ceragon Proprietary and Confidential...
Page 400
1 In the file, configure the usr/share/freeradius/dictionary.ceragon values of the access channels according to the following example: access channel for u1 user:serial+telnet+ssh+web+nms+snmp+snmpV4 VALUE ACCESS_CHANNEL u1accesschannel 2 Save the changes to the file. usr/share/freeradius/dictionary.ceragon Page 400 of 825 Ceragon Proprietary and Confidential...
1 Create and upload a CSR file. See Generating a Certificate Signing Request (CSR) File. 2 Download the certificate to the IP-20 and install the certificate. See Downloading a Certificate. 3 Enable HTTPS. This must be performed via CLI. See Enabling HTTPS (CLI). Page 401 of 825 Ceragon Proprietary and Confidential...
8 In the Email field, enter an e-mail address that can be used to contact your organization. 9 In the File Format field, select PEM or DER to determine the file format. Note: In this version, only PEM is supported. Page 402 of 825 Ceragon Proprietary and Confidential...
Ready – The default value, which appears when CSR generation and upload is • in progress. • File-in-transfer – The upload operation is in progress. • Success – The file has been successfully uploaded. Page 403 of 825 Ceragon Proprietary and Confidential...
You can block telnet access to the unit. By default, telnet access is not blocked. To block telnet access: 1 Select Platform > Security > Protocols Control. The Protocols Control page opens. Page 405 of 825 Ceragon Proprietary and Confidential...
1 Install and configure an FTP server on the PC or laptop you are using to perform the upload. See Installing and Configuring an FTP or SFTP Server. 2 Select Platform > Security > General > Security Log Upload. The Security Log Upload page opens. Page 406 of 825 Ceragon Proprietary and Confidential...
3 Click FTP Parameters to display the FTP Parameters page. Figure 321: FTP Parameters Page (Security Log Upload) 4 In the Username field, enter the user name you configured in the FTP server. Page 407 of 825 Ceragon Proprietary and Confidential...
1 Install and configure an FTP server on the PC or laptop you are using to perform the upload. See Installing and Configuring an FTP or SFTP Server. 2 Select Platform > Security > General > Configuration Log Upload. The Configuration Log Upload page opens. Page 408 of 825 Ceragon Proprietary and Confidential...
3 Click FTP Parameters to display the FTP Parameters page. Figure 323: FTP Parameters Page (Configuration Log Upload) 4 In the Username field, enter the user name you configured in the FTP server. Page 409 of 825 Ceragon Proprietary and Confidential...
Page 410
Success – The file has been successfully uploaded. • • Failure – The file was not successfully uploaded. The File transfer progress field displays the progress of any current configuration log upload operation. Page 410 of 825 Ceragon Proprietary and Confidential...
Table 72: Alarm Information. Figure 324: Current Alarms Page 2 To view more detailed information about an alarm, click + at the beginning of the row or select the alarm and click View. Page 411 of 825 Ceragon Proprietary and Confidential...
This field only appears in the Current Alarms - View page. One or more possible corrective actions to be taken in troubleshooting the alarm. Alarm ID A unique ID that identifies the alarm type. Page 412 of 825 Ceragon Proprietary and Confidential...
Event Log, see Table 73: Event Log Information. 2 To export the Event Log to a CSV file, click Export to CSV in the lower right corner of the Event Log page. Figure 327: Event Log Page 413 of 825 Ceragon Proprietary and Confidential...
Note: You can add user text to events in the Alarm Configuration page. See Editing Alarm Text and Severity and Disabling Alarms and Events. Origin The module that generated the event. Page 414 of 825 Ceragon Proprietary and Confidential...
The severity assigned to the alarm type. You can edit the severity in the Alarm Configuration – Edit page. See Editing an Alarm Type and Disabling Alarms and Events. Description A system-defined description of the alarm. Page 415 of 825 Ceragon Proprietary and Confidential...
If an alarm is disabled while raised, the timeout count begins to run upon disabling the alarm, and an alarm cleared trap is sent when the timeout expires. Page 416 of 825 Ceragon Proprietary and Confidential...
5 Click Apply, then Close. 11.4.4 Setting Alarms to their Default Values To set all alarms to their default severity levels and text descriptions, click Set All to Default in the Alarm Configuration page (Figure 328). Page 417 of 825 Ceragon Proprietary and Confidential...
Alarm #32000: Under voltage • Alarm #32001: Over voltage • To voltage alarm thresholds: 1 Select Faults > Voltage Alarm Configuration. The Voltage Alarm Configuration page opens. Figure 331: Voltage Alarm Configuration Page Page 418 of 825 Ceragon Proprietary and Confidential...
The lowest voltage during the measured period. The highest voltage during the measured period. • These PMs are displayed via CLI. For instructions, see Configuring Voltage Alarm Thresholds and Displaying Voltage Threshold PMs (CLI). Page 419 of 825 Ceragon Proprietary and Confidential...
4 In the Username field, enter the user name you configured in the FTP server. 5 In the Password field, enter the password you configured in the FTP server. If you did not configure a password for your FTP user, simply leave this field blank. Page 420 of 825 Ceragon Proprietary and Confidential...
Page 421
Error #3-Invalid set value. If this occurs, wait about two minutes then click Export again. ◦ File transfer progress – Displays the progress of the current Unit Information file upload operation. Page 421 of 825 Ceragon Proprietary and Confidential...
You cannot perform loopback directly on a Multi-Carrier ABC group. To perform traffic-level diagnostics on a Multi-Carrier ABC group, the loopback must be activated for all members of the group. Radio-level diagnostics can still be performed on individual members of the group. Page 422 of 825 Ceragon Proprietary and Confidential...
SOAM. • MA/MEG (Maintenance Association/Maintenance Entity Group) – An MA/MEG contains a set of MEPs or MIPs. Page 424 of 825 Ceragon Proprietary and Confidential...
Fast MEGs have a CCM interval of 1 second. • • Slow MEGs have a CCM interval of 10 seconds, 1 minute, or 10 minutes. You can configure up to 32 MEP pairs per network element. To add a MEG: Page 426 of 825 Ceragon Proprietary and Confidential...
Figure 340: SOAM MA/MEG – Add Page 3 Configure the fields described in Table 75. 4 Click Apply, then Close. Table 76 describes the status (read-only) fields in the SOAM MA/MEG Component table. Page 427 of 825 Ceragon Proprietary and Confidential...
Select an Ethernet service to which the MEG belongs. You must define the service before you configure the MEG. Table 76: SOAM MA/MEG Status Parameters Parameter Definition MIP Creation Determines whether MIPs are created on the MEG. Options are: Page 428 of 825 Ceragon Proprietary and Confidential...
Page 429
3 Enable the Local MEPs. See Enabling Local MEPs. Adding Local and Remote MEPs To add a MEP to the MA/MEG: 1 In the SOAM MA/MEG page, select a MA/MEG and click MEP List. The MEP List page opens. Page 429 of 825 Ceragon Proprietary and Confidential...
3 In the MEP ID field, enter a MEP ID (1-8191). 4 Click Apply, then Close. Configuring the Local MEPs Once you have added local and remote MEPs, you must define the MEPs and determine which are the local MEPs: Page 430 of 825 Ceragon Proprietary and Confidential...
2 Click Add. Page 1 of the Add SOAM MEP wizard opens. Figure 344: Add SOAM MEP Wizard – Page 1 3 In the MA/MEG Name field, select an MA/MEG. 4 Click Next. Page 2 of the Add SOAM MEP wizard opens. Page 431 of 825 Ceragon Proprietary and Confidential...
8 Click Finish. The Add SOAM MEP wizard displays the parameters you have selected. Figure 346: Add SOAM MEP Wizard –Summary Page 9 Verify that you want to submit the displayed parameters and click Submit. Page 432 of 825 Ceragon Proprietary and Confidential...
Once you have added a MEP and defined it as a local MEP, you must enable the MEP. To enable a MEP: 1 In the SOAM MEP page (Figure 343), select the MEP you want to enable. Page 433 of 825 Ceragon Proprietary and Confidential...
To display a list of remote MEPs (RMEPs) and their parameters: 1 Select Ethernet > Protocols > SOAM > MEP. The SOAM MEP page opens (Figure 343). 2 Select a MEP and click RMEP List. The SOAM MEP DB table is displayed. Page 434 of 825 Ceragon Proprietary and Confidential...
MEP has been defined. RMEP Last rx CCM Chassis Displays the format of the remote chassis (always the MAC address). ID Format RMEP Last rx CCM Chassis Displays the MAC address of the remote chassis. Page 435 of 825 Ceragon Proprietary and Confidential...
MEGs with the MHF none attribute on the same service on lower levels then the MEG with the MHF default attribute. MEPs cannot be attached to a MEG with the MHF default attribute. • Page 436 of 825 Ceragon Proprietary and Confidential...
Page 437
1 Create a MEG with the MHF none attribute on the intended Ethernet service. See Configuring MA/MEGs. 2 Select the MEG and click Edit. The SOAM MA/MEG – Edit page opens. 3 In the MIP Creation field, select MHF Default. 4 Click Apply, then Close. Page 437 of 825 Ceragon Proprietary and Confidential...
1 In the SOAM MEP page (Figure 343), select the MEP on which you want to perform the loopback. 2 Click Loopback. The SOAM MEP – Loopback page opens. Figure 350: SOAM MEP Loopback Page Page 438 of 825 Ceragon Proprietary and Confidential...
Page 439
A MIP has been defined on the destination interface. See Configuring MIPs with MHF Default. Note: To manually stop a loopback, you must use the CLI. Enter the following command in root view: root> ethernet soam loopback stop meg-id <meg-id> mep-id <mep-id> Page 439 of 825 Ceragon Proprietary and Confidential...
Calculate the ifIndex for any object in the system. Determine the object represented by any valid ifIndex. • To use the ifIndex calculator: 1 Select Utilities > ifCalculator. The ifIndex Calculator page opens. Page 440 of 825 Ceragon Proprietary and Confidential...
1 Select Utilities > ifCalculator. The ifIndex Calculator page opens. Figure 353: MIB Reference Table Page The MIB Reference Table is customized to the type of IP-20 product you are using. There are three separate versions of the MIB Reference Table: Page 441 of 825 Ceragon Proprietary and Confidential...
Page 442
To search for a text string, enter the string in the Search field and press <Enter>. Items that contain the string are displayed in yellow. Searches are not case-sensitive. • To save the MIB Reference Table as a .csv file, click Save to File. Page 442 of 825 Ceragon Proprietary and Confidential...
Guide for the type of unit you are connecting for cable connection instructions. Note: The IP-20 IP address, as well as the password, should be changed before operating the system. See Changing the Management IP Address (CLI) and Changing Your Password (CLI). Page 444 of 825 Ceragon Proprietary and Confidential...
At the prompt, enter the default login user name: admin A password prompt appears. Enter the default password: admin The root prompt appears. For example: login: admin Password: Last login: Mon Apr 13 11:27:02 on console IP20C root> Page 445 of 825 Ceragon Proprietary and Confidential...
This parameter can be an integer from 64 to 1480. The default value is 64. command is available from all views (e.g., root, interface views, group ping views). Page 446 of 825 Ceragon Proprietary and Confidential...
In addition to the Admin password, there is an additional password protected user account, “root user”, which is configured in the system. The root user password and instructions for changing this password are available from Ceragon Customer Support. It is strongly recommended to change this password.
Note: When you enable or disable Mate Management Access, the unit is reset. To disable Mate Management Access, enter the following command: root> platform management mate-access admin disable Page 448 of 825 Ceragon Proprietary and Confidential...
Page 449
To display whether Mate Management Access is enabled, enter the following command: root> platform management mate-access show Notes: Mate Management Access can only be configured via CLI. Upon recovery from a failure event, management may be lost for up to 40 seconds. Page 449 of 825 Ceragon Proprietary and Confidential...
The subnet mask for the unit. gateway Dotted decimal format. Any valid IPv4 address. The default gateway for the unit (optional). name Text String. Enter a name (optional). description Text String. Enter a description (optional). Page 450 of 825 Ceragon Proprietary and Confidential...
13.9.2 Viewing the Activation Key Status Parameters (CLI) To display information about the currently installed activation key, enter the following command in root view: root> platform activation-key show information Page 452 of 825 Ceragon Proprietary and Confidential...
350M and one activation key for 300M. For instructions on how to reclaim an activation key, refer to the User Guide for the Ceragon Activation Key Management System, Rev A.15 or later, Chapter 7, Reclaiming an Activation Key. During the activation key reclaim procedure, you will need to obtain a Validation Number from the IP-20 unit.
Table 82: Local Time Configuration CLI Parameters Parameter Input Type Permitted Values Description date-and-time Number dd-mm-yyyy,hh:mm:ss Sets the UTC time. where: dd = date mm = month yyyy= year hh = hour mm = minutes ss = seconds Page 454 of 825 Ceragon Proprietary and Confidential...
The following command configures daylight savings time as starting on May 30 and ending on October 1, with an offset of 20 hours. root> platform management time-services daylight-savings-time set start-date-month 5 start-date-day 30 end-date-month 10 end- date-day 1 offset 20 Page 455 of 825 Ceragon Proprietary and Confidential...
The following command disables radio interface 1: root> platform if-manager set interface-type radio slot 2 port 1 admin down The following command disables Ethernet port 3: root> platform if-manager set interface-type ethernet slot 1 port 3 admin down Page 456 of 825 Ceragon Proprietary and Confidential...
2 in a multi-carrier unit: radio[2/2]>mrmc script show script-type normal acm-support yes The following command displays available symmetrical (normal) scripts for radio carrier 1: radio[2/1]>mrmc script show script-type normal acm-support yes Page 457 of 825 Ceragon Proprietary and Confidential...
(MRMC) Script(s) (CLI). For example, if you select a maximum profile of 5, the system will not climb above profile 5, even if channel fading conditions allow it. Page 458 of 825 Ceragon Proprietary and Confidential...
Page 459
5, to the radio carrier in an IP-20E unit. This is the functional equivalent of assigning a fixed profile. radio[2/1]>mrmc set acm-support script-id 4701 modulation max- profile 5 min-profile 5 Page 459 of 825 Ceragon Proprietary and Confidential...
Radio Carrier 2 (IP-20C and IP-20C-HP only): 2 The following command enters radio view for radio carrier 1: root> radio slot 2 port 1 The following prompt appears: radio[2/1]> Page 460 of 825 Ceragon Proprietary and Confidential...
The following command configures a timed mute on radio carrier 1. This mute will automatically expire in 30 minutes. radio[2/1]> rf mute set admin on-with-timer timeout-value 30 Page 461 of 825 Ceragon Proprietary and Confidential...
The following command sets the TX frequency of the radio in an IP-20E unit to 71000000 KHz, but does not set the RX frequency of the remote unit. radio[2/1]> rf set rx-frequency 71000000 local-remote disable Page 462 of 825 Ceragon Proprietary and Confidential...
Number Depends on hardware The desired TX signal model. level (TSL), in dBm. The following command sets the TX level of radio carrier 1 to 10 dBm: radio[2/1]>rf set tx-level 10 Page 463 of 825 Ceragon Proprietary and Confidential...
RF adaptive power operational status: [up/down] means the feature is enabled and RF adaptive power operational status: Up fully functional for that radio link. Note that the feature is configured and operates independently for each radio link. Page 464 of 825 Ceragon Proprietary and Confidential...
The alarm is cleared when the RSL goes above the configured threshold. The alarm is masked if the radio interface is disabled, the radio does not exist, or a communication-failure alarm (Alarm ID #1703) is raised. Page 465 of 825 Ceragon Proprietary and Confidential...
13.16.1 Requirements for FIPS Compliance (CLI) For a full list of FIPS requirements, refer to the Ceragon IP-20 FIPS 140-2 Security Policy, available upon request. It is the responsibility of the customer to ensure that these requirements are met.
User Guide for FibeAir® IP-20 All-Outdoor Products, CeraOS 10.5 13.18 Creating Service(s) for Traffic (CLI) In order to pass traffic through the IP-20, you must configure Ethernet traffic services. For configuration instructions, see Configuring Ethernet Services (CLI). Page 467 of 825 Ceragon Proprietary and Confidential...
IP-20C (hub site or tail site) Configuring Advanced Frequency IP-20S (tail site only) Reuse (AFR) (CLI) IP-20C in Single Radio Carrier Mode IP-20C Operating an IP-20C or IP-20C-HP in IP-20C-HP Single Radio Carrier Mode (CLI) Page 468 of 825 Ceragon Proprietary and Confidential...
[1]> attach-member slot 2 port <port> channel-id <1-16> ◦ The Channel ID identifies the interface within the group. 4 Repeat for the second radio interface. Page 469 of 825 Ceragon Proprietary and Confidential...
Carrier ABC Group – Edit Group page (Figure 74). To enable Multi-Carrier ABC Minimum Bandwidth Override, enter the following command in root view: root> platform if-manager set group-type abc group-number <1-4> minimum-bw-admin enable Page 470 of 825 Ceragon Proprietary and Confidential...
1 Remove the members from the group. See Removing Members from a Multi- Carrier ABC Group (CLI). 2 Delete the group by entering the following command in root view: root> multi-carrier-abc delete group group_id 1 Page 471 of 825 Ceragon Proprietary and Confidential...
[1] slot [1]>attach-member slot 2 port 1 channel-id 1 Note: parameter must be set to 1 for the radio interface channel-id and 2 for the Ethernet interface. Page 472 of 825 Ceragon Proprietary and Confidential...
Page 473
Multi-Carrier ABC group. See Configuring Ethernet Services (CLI). 7 On the IP-20C or IP-20S, configure Automatic State Propagation with ASP trigger by remote fault enabled. See Configuring Automatic State Propagation and Link Loss Forwarding (CLI). Page 473 of 825 Ceragon Proprietary and Confidential...
RX capacity, go to Multi-Carrier ABC group view and enter the following command: multi-carrier-abc enhanced-group-id [1] slot [1]>summary-show To display port counters for a Multiband group, go to Multi-Carrier ABC group view and enter the following command: multi-carrier-abc enhanced-group-id [1] slot [1]>show-ethernet- port-counters Page 474 of 825 Ceragon Proprietary and Confidential...
There are no restrictions on the number of interfaces that can be included in a LAG. It is recommended, but not required, that each interface in the LAG have the same parameters (e.g., speed, duplex mode). Page 475 of 825 Ceragon Proprietary and Confidential...
LAG and enter the following command: eth group [lagx]>lacp admin show The following commands enable LACP for LAG group 1: root> ethernet interfaces group lag1 eth group [lag1]>lacp admin set enable eth group [lag1]> Page 476 of 825 Ceragon Proprietary and Confidential...
Ethernet: 1 Depends on the Radio: 2 interface and unit type. port Number GbE 1: 1 The port number of the interface. GbE 2: 2 GbE 3: 3 Radio Carrier 1: 1 Page 477 of 825 Ceragon Proprietary and Confidential...
Page 478
Static-lag group name: lag2 The following commands display details about the LAG: root> ethernet interfaces group lag2 eth group [lag2]> eth group [lag2]> port static-lag show members Static-lag members ------------------- Eth#[1/1] Eth#[1/2] Radio#[2/1] Page 478 of 825 Ceragon Proprietary and Confidential...
To display the current LAG group shutdown in case of degradation event option setting, go to interface view for the LAG and enter the following command: eth group [lagx]> static-lag show lag-degrade-admin Page 479 of 825 Ceragon Proprietary and Confidential...
You can display the following LACP parameters and statistics: LACP Aggregation (per LAG) • LACP Port Status • • LACP Port Statistics • LACP Port Debug Statistics Note: IP-20 does not support any LACP write parameters. Page 480 of 825 Ceragon Proprietary and Confidential...
The priority value associated with the Partner’s System ID. Partner Oper Key The current operational value of the Key for the Aggregator’s current Protocol partner. Collector Max Delay The maximum delay, in tens of microseconds. Page 481 of 825 Ceragon Proprietary and Confidential...
System ID The MAC Address value that defines the value of the System ID for the system that contains this Aggregation Port. Port Priority The priority value assigned to this Aggregation Port. Page 482 of 825 Ceragon Proprietary and Confidential...
Page 483
Partner Oper System ID The MAC Address value representing the current value of the Aggregation Port’s protocol Partner’s System ID. Partner Oper Port The Priority value assigned to this Aggregation port by the Partner. Priority Page 483 of 825 Ceragon Proprietary and Confidential...
The number of LACPDUs that this port has transmitted. Illegal RX The number of illegal protocol frames that this port has received. Unknown RX The number of unknown protocol frames that this port has received. Page 484 of 825 Ceragon Proprietary and Confidential...
Create an XPIC group. See Creating an XPIC Group (CLI). 14.5.3 Creating an XPIC Group (CLI) To create an XPIC group, enter the following commands: root> radio-groups radio-groups> radio-groups> xpic set admin enable Page 485 of 825 Ceragon Proprietary and Confidential...
RSL of the vertical carrier of the remote unit, within ±2dB. The RSL of the vertical carrier of the local unit should match the RSL of the horizontal carrier of the remote unit, within ±2dB. Page 486 of 825 Ceragon Proprietary and Confidential...
To display the status of an XPIC group, enter the following command in radio- groups view: radio-groups> xpic show status The following is a typical command output: XPIC: Carrier 1: Radio #[2/1] ; Carrier 2: Radio #[2/2] Admin mode: enable XPIC state: XPIC-Idle Page 487 of 825 Ceragon Proprietary and Confidential...
• Split Protection Mode – Only available for optical Ethernet ports. An optical splitter cable is used to connect to both the active and the standby optical Ethernet ports. Page 488 of 825 Ceragon Proprietary and Confidential...
Displaying Unit Inventory (CLI)) and the same software version (see Viewing Current Software Versions (CLI)). If the units do not have the same software version, upgrade each unit to the most recent software release (see Configuring a Software Download (CLI)). Page 489 of 825 Ceragon Proprietary and Confidential...
In order to configure 2+2 HSB unit protection on an IP-20C or IP-20C-HP unit, you must simply enable the second radio carrier on both units on both sides of the link. No other configuration is necessary other than the configuration described above. Page 490 of 825 Ceragon Proprietary and Confidential...
To run CLI commands in the standby unit: 1 Use the following command to enter view context for the standby unit: root> switch-to mate mate/root> 2 Enter the specific CLI command you want to run in mate/root context. Page 491 of 825 Ceragon Proprietary and Confidential...
Disabling Automatic Switchover to the Standby Unit (CLI) At any point, you can perform lockout, which disables automatic switchover to the standby unit. To disable automatic switchover to the Standby unit, use the following command in root view: Page 492 of 825 Ceragon Proprietary and Confidential...
IP address (192.168.1.1) To disable protection, enter the following command in root view. root> platform management protection set admin disable Page 493 of 825 Ceragon Proprietary and Confidential...
If you mute the interface before configuring unit protection, you must make sure to manually mute the interface on both IP-20 units. Otherwise, configuring unit protection will override the mute configuration. Page 494 of 825 Ceragon Proprietary and Confidential...
IP-20C unit, both radio carriers are connected to a single antenna. One optical GbE port on each IP-20C is connected to an optical splitter. Traffic must be routed to an optical GbE port on each IP-20C unit. Page 495 of 825 Ceragon Proprietary and Confidential...
Slave IP-20C units on each side of the link. For details, refer to the IP-20C Installation Guide or the IP-20C-HP Installation Guide: ◦ Source sharing cable between both EXT REF IP-20 radio connectors. Page 496 of 825 Ceragon Proprietary and Confidential...
Page 497
1, group_type mimo-4x4 created root> amcc group group_id 1 group_type mimo_4x4 mimo-4X4-group[1]> amcc attach slot 2 port 1 role mimo-master mimo-4X4-group[1]> amcc attach slot 2 port 2 role mimo-master mimo-4X4-group[1]> set admin enable Page 497 of 825 Ceragon Proprietary and Confidential...
<second radio carrier in the group: either 2 or 1 > where defines the Space Diversity configuration. The options <mimo-type> are: ◦ – 1+0 Space Diversity. 1-plus-0-sd ◦ – 2+0 Space Diversity. 2-plus-0-sd Page 498 of 825 Ceragon Proprietary and Confidential...
1-plus-0-sd – 1+0 BBS Space Diversity. • 2-plus-0-sd – 2+0 XPIC with BBS Space Diversity. MIMO group 1st member The first radio carrier in the group. MIMO group 2nd member The second radio carrier in the group. Page 499 of 825 Ceragon Proprietary and Confidential...
You can delete a 2x2 MIMO or Space Diversity Group. To delete a 2x2 MIMO or Space Diversity Group: 1 Before deleting a MIMO or Space Diversity group, you must first disable the group using the following command in root view: Page 500 of 825 Ceragon Proprietary and Confidential...
Page 501
When the MIMO or Space Diversity group is disabled, the system is automatically reset. 2 Delete the MIMO or Space Diversity group by entering the following command in root view: root > radio mimo delete group 1 Page 501 of 825 Ceragon Proprietary and Confidential...
4 Enter the following command to enable the group. When you execute the command, the unit is automatically reset. Page 502 of 825 Ceragon Proprietary and Confidential...
[1]> amcc detach slot 2 port <port> 4 Exit group view and enter the following command in root view to delete the group: root> amcc delete group group_id 1 Page 503 of 825 Ceragon Proprietary and Confidential...
2 Disable Multi-Carrier ABC, as described in Deleting a Multi-Carrier ABC Group (CLI). 3 Disable one of the two radio interfaces, as described in Enabling the Interfaces (CLI). 4 Mute the disabled radio interface, as described in Muting and Unmuting a Radio (CLI). Page 504 of 825 Ceragon Proprietary and Confidential...
To set the remote radio’s IP Address, enter the following command in radio view: radio[x/x]>remote-unit set ip-address <ipv4-address> To display the remote radio’s IP Address, enter the following command in radio view: Page 505 of 825 Ceragon Proprietary and Confidential...
To set the remote radio’s prefix length, enter the following command in radio view: radio[x/x]>remote-unit set prefix-length <prefix-length > To display the remote radio’s prefix-length, enter the following command in radio view: radio[x/x]>remote-unit show prefix-length Page 506 of 825 Ceragon Proprietary and Confidential...
IPv6 FE80:0000:0000:0000:0202:B3FF:FE1E:8329 The following commands set the IP address of the remote radio as FE80:0000:0000:0000:0202:B3FF:FE1E:8329, with a prefix length of 64: radio[2/2]>remote-unit set ip-address-ipv6 FE80:0000:0000:0000:0202:B3FF:FE1E:8329 radio[2/2]>remote-unit set prefix-length 64 Page 507 of 825 Ceragon Proprietary and Confidential...
Text String Any valid SNMP read The community string for the community. SNMP read community. write-community Text String Any valid SNMP write The community string for the community. SNMP write community. Page 508 of 825 Ceragon Proprietary and Confidential...
Page 509
“public” and the write community to “private”: root> platform security protocols-control snmp admin set enable root> platform security protocols-control snmp version set v2 root> platform security protocols-control snmpv1v2 set read- community public write-community private Page 509 of 825 Ceragon Proprietary and Confidential...
(privacy) protocol to be used for this user. v3-auth-algorithm Variable None Defines the authentication algorithm to be used for this user. v3-access-mode Variable readWrite Defines the access permission level for this readOnly user. Page 510 of 825 Ceragon Proprietary and Confidential...
15.3.4 Configuring Trap Managers (CLI) To display the current SNMP trap manager settings, enter the following command in root view: root> platform security protocols-control snmp trap-manager show Page 511 of 825 Ceragon Proprietary and Confidential...
V3, enter the name of a V3 user defined in the system. Note: Make sure that an identical V3 user is also defined on the manager's side Page 512 of 825 Ceragon Proprietary and Confidential...
When upgrading a node with unit protection, upgrade the standby unit first, then the active unit. 15.5.2 Viewing Current Software Versions (CLI) To display all current software versions, enter the following command in root view: root> platform software show versions Page 515 of 825 Ceragon Proprietary and Confidential...
Enter the path relative to the FTP user's home directory, not the absolute path. If the location is the home directory, it should be left empty. If the Page 516 of 825 Ceragon Proprietary and Confidential...
IP-20C, IP-20C-HP to IP-20C-HP, IP-20S to IP-20S, IP-20E to IP-20E, and IP-20V to IP-20V. Note that you can also write CLI scripts that will automatically execute a series of commands when the configuration file is restored. For information, refer to Editing CLI Scripts (CLI). Page 518 of 825 Ceragon Proprietary and Confidential...
See Setting the Time and Date (Optional) (CLI). To set the FTP or SFTP parameters for configuration file import and export, enter one of the following commands in root view: Page 519 of 825 Ceragon Proprietary and Confidential...
Otherwise, the file import may fail. You can export the file using any name, then add the suffix .zip manually. username Text String. The user name you configured in the FTP server. Page 520 of 825 Ceragon Proprietary and Confidential...
Setting the Configuration Management Parameters and Backing up and Exporting a Configuration File. To import a configuration file, enter the following command in root view: root> platform configuration configuration-file import <restore-point> Page 521 of 825 Ceragon Proprietary and Confidential...
Setting the Unit to the Factory Default Configuration (CLI) To restore the unit to its factory default configuration, while retaining the unit’s IP address settings and logs, enter the following commands in root view: Page 522 of 825 Ceragon Proprietary and Confidential...
<unit_measure_format> To display the type of measurement unit used by the system, enter the following command in root view: root> platform management show unit_measure_format Page 523 of 825 Ceragon Proprietary and Confidential...
Enter enable or disable to enable or disable the NTP server. disable ntp-version Variable. Enter the NTP version you want to use. NTPv4 provides interoperability with NTP v3 and with SNTP. Page 524 of 825 Ceragon Proprietary and Confidential...
Page 525
The following command enables NTP, using NTP v4, and sets the IP address of the NTP server as 62.90.139.210. root> platform management ntp set admin enable ntp-version ntpv4 ntp-server-ip-address-1 Page 525 of 825 Ceragon Proprietary and Confidential...
: IP-20 Subtype : 350 part number : 22-0001-0| serial number : F493606212 company name : Ceragon Networks Ltd. product name : AODU DC, All-outdoor, dual radio carriers in one product product description : AODU DC, All-outdoor, dual radio carriers in one product root>...
Vendor Name Displays the name of the SFP’s vendor. Vendor Part Number Displays the vendor’s part number for the SFP module. Vendor Serial Number Displays the vendor’s serial number for the SFP module. Page 527 of 825 Ceragon Proprietary and Confidential...
If the Admin status of the port is Down, the TX Power Level is displayed as -40 DBm and the Bias Current is displayed as 0 mA. The Temperature is always shown as long as the SFP module is inserted in the port. Page 528 of 825 Ceragon Proprietary and Confidential...
RX and TX power levels are collected five times per 15-minute interval. 15- minute PM data is saved for 24 hours. 24-hour PM data, which is updated every 15 minutes, is saved for 30 days. Page 529 of 825 Ceragon Proprietary and Confidential...
To display the transmit (TX) level of the remote radio, enter the following command in radio view: radio[x/x]>remote-unit show tx-level Table 111: Remote Radio TX Level CLI Parameters Parameter Input Type Permitted Values Description Page 531 of 825 Ceragon Proprietary and Confidential...
In a configuration with unit protection, the ATPC override state is propagated to the standby unit in the event of switchover. Notes: When canceling an ATPC override state, you should ensure that the underlying problem has been corrected. Otherwise, ATPC may be overridden again. Page 532 of 825 Ceragon Proprietary and Confidential...
Page 533
Possible values are: • Normal – ATPC override is enabled, and there is no override. • Disabled – ATPC override is not enabled. Override – ATPC override has been activated. • Page 533 of 825 Ceragon Proprietary and Confidential...
RSL reference level of -55, an ATPC override timeout of 15 minutes, and an override TX level of 18 dBm: radio[2/1]>atpc set admin enable radio[2/1]>atpc set rx-level atpc_ref_rx_level -55 radio[2/1]>atpc set override timeout 900 radio[2/1]>atpc override set admin enable radio[2/1]> atpc set override-tx-level 18 Page 534 of 825 Ceragon Proprietary and Confidential...
2, Layer 3, and on the Tunnel layer for packets carrying GTP or GRE frames. Tunnel-Layer3 - Header De-Duplication operates on Layer 2, Layer 3, and on the Tunnel and T-3 layers for packets carrying GTP or GRE frames. Page 535 of 825 Ceragon Proprietary and Confidential...
Page 536
4 layers for packets carrying GTP or GRE frames. The following command enables Layer 2 Header De-Duplication on radio carrier 1: root> radio slot 2 port 1 radio[2/1]> compression header-compression set Layer2 Page 536 of 825 Ceragon Proprietary and Confidential...
Frame Cut-Through cannot be used together with 1588 Transparent Clock. To enable Frame Cut-Through, enter the following command in radio view: radio[2/1]> cut-through mode yes To disable Frame Cut-Through, enter the following command in radio view: Page 537 of 825 Ceragon Proprietary and Confidential...
Page 538
To display the number of frames and bytes that have been transmitted via Frame Cut-Through, enter the following command in radio view: radio[2/1]> cut-through show-counters Page 538 of 825 Ceragon Proprietary and Confidential...
The following is a sample output of this command in which payload encryption is enabled but not operational on radio interface 1, and disabled on radio interface Page 539 of 825 Ceragon Proprietary and Confidential...
Page 540
Once payload encryption has been enabled on both sides of the link, the Key Exchange Protocol periodically Page 540 of 825 Ceragon Proprietary and Confidential...
Page 541
Enter the regeneration interval in hours and minutes (HH:MM). For example, the following command configures radio interface 1 to regenerate the session key every 4 hours and 15 minutes: Payload Encryption [2/1]> payload encryption session-key period set 04:15 Page 541 of 825 Ceragon Proprietary and Confidential...
Page 542
Warning! Executing this command on a FIPS-enabled unit formats the unit’s disk, and renders the unit non-operational. If it is necessary to use this command, contact Ceragon Technical Support for instructions how to re-configure the unit. This command has no effect on units that are not enabled for FIPS.
To display modem BER PMs in 15-minute intervals, enter the following command in radio view: radio [x/x]>framer pm-aggregate show interval 15min The following is a partial sample output of the framer pm-aggregate show command: interval 15min Page 543 of 825 Ceragon Proprietary and Confidential...
Indicates the number of seconds in the measuring interval during which errors occurred. Indicates the number of severe error seconds in the measuring interval. Page 544 of 825 Ceragon Proprietary and Confidential...
You can set two RSL (RX Signal Level) thresholds. The number of seconds during which the RSL exceeds these thresholds are counted as RSL Exceed Threshold Seconds. See Displaying RSL and TSL Levels (CLI). Page 545 of 825 Ceragon Proprietary and Confidential...
To display RSL and TSL PMs in daily intervals, enter the following command in radio view: radio [x/x]>rf pm-rsl-tsl show interval 24hr The following is the output format of the commands: rf pm-rsl-tsl show Page 546 of 825 Ceragon Proprietary and Confidential...
Page 547
User Guide for FibeAir® IP-20 All-Outdoor Products, CeraOS 10.5 Page 547 of 825 Ceragon Proprietary and Confidential...
[x/x]>modem signal-degrade set threshold 1e-7 To display the Signal Degrade BER threshold, enter the following command in radio view: radio [x/x]>modem signal-degrade show threshold Page 548 of 825 Ceragon Proprietary and Confidential...
Description threshold Number -99 - -1 The MSE threshold. To display MSE (Mean Square Error) PMs in 15-minute intervals, enter the following command in radio view: radio [x/x]>modem pm-mse show interval 15min Page 549 of 825 Ceragon Proprietary and Confidential...
Table 123: XPI Threshold CLI Parameters Parameter Input Type Permitted Values Description threshold Number 0-99 The XPI threshold. To display XPI PMs in 15-minute intervals, enter the following command in radio view: radio[x/x]>modem pm-xpi show interval 15min Page 551 of 825 Ceragon Proprietary and Confidential...
Page 552
0.00 55.00 0.00 55.00 0.00 55.00 0.00 55.00 0.00 55.00 0.00 radio [2/1]> To display XPI PMs in daily intervals, enter the following command in radio view: radio[x/x]>modem pm-xpi show interval 24hr Page 552 of 825 Ceragon Proprietary and Confidential...
Indicates the highest XPI value in dB, measured during the interval. XPI Below Threshold Seconds Indicates the number of seconds the XPI value was lower than the XPI threshold during the interval. Page 553 of 825 Ceragon Proprietary and Confidential...
43389 43389 43389 43389 43389 43389 43389 43389 43389 43389 radio [2/1]> To display ACM PMs in daily intervals, enter the following command in radio view: radio [x/x]>mrmc pm-acm show interval 24hr Page 554 of 825 Ceragon Proprietary and Confidential...
Indicates the maximum ACM profile that was measured during the interval. Min bitrate Indicates the minimum total radio throughput (Mbps), delivered during the interval. Max bitrate Indicates the maximum total radio throughput (Mbps), delivered during the interval. Page 555 of 825 Ceragon Proprietary and Confidential...
32 service points. A Management service can hold up 30 service points. For a more detailed overview of the IP-20 service-oriented Ethernet switching engine, refer to the Technical Description for the IP-20 product type you are using. Page 556 of 825 Ceragon Proprietary and Confidential...
Once you have added the service, you cannot change the Service ID. Service ID 257 is reserved for a pre- defined management service. service admin mode Variable Operational The administrative state of the service: reserved Page 557 of 825 Ceragon Proprietary and Confidential...
Page 558
17.1.3.2 Entering Service View (CLI) To view service details and set the service’s parameters, you must enter the service’s view level in the CLI. To enter a service’s view level: root> ethernet service sid <sid> Page 558 of 825 Ceragon Proprietary and Confidential...
To display the attributes of a service and its service points, go to service view for the service and enter the following command: service[SID]>service detailed-info show Page 559 of 825 Ceragon Proprietary and Confidential...
Table 129: Ethernet Service Operational State CLI Parameters Parameter Input Type Permitted Values Description service admin mode Variable Operational The administrative state of the service: reserved • operational - The service is functional. Page 560 of 825 Ceragon Proprietary and Confidential...
- Frames passing through the preserve-sp-cos- service are assigned decision the default CoS defined below. This CoS value overrides whatever CoS may have been assigned at the service point or interface level. Page 561 of 825 Ceragon Proprietary and Confidential...
To display a service’s EVC description, go to service view for the service and enter the following command: service[SID]>service description show Table 131: Ethernet Service EVC CLI Parameters Parameter Input Type Permitted Values Description Page 562 of 825 Ceragon Proprietary and Confidential...
Any defined Service The Service ID. The following command deletes Service 10: root>ethernet service delete sid 10 The following command deletes Services 10 through 15: root>ethernet service delete sid 10 to 15 Page 563 of 825 Ceragon Proprietary and Confidential...
Table 133 summarizes the service point types available per service type. Table 133: Service Points per Service Type Service Point Type Pipe Service Management Type Point-to-Point Multipoint Table 134 shows which service point types can co-exist on the same interface. Page 564 of 825 Ceragon Proprietary and Confidential...
Bundle C-Tag – A set of multiple C-VLANs is classified to the service point. • • Bundle S-Tag – A single S-VLAN and a set of multiple C-VLANs are classified to the service point. Page 565 of 825 Ceragon Proprietary and Confidential...
Q in Q 802. Type Interface Type 802.1q Bundle-C Bundle-S All to One Only 1 All to One SP Allowed Q in Q 802.1q S-Tag Pipe 802.1q S-Tag 802.1q Q in Q S-Tag Page 566 of 825 Ceragon Proprietary and Confidential...
<sp-id> [interface|group] <interface|group> slot <slot> port <port> sp-name <sp-name> To add a service point with a Dot1q interface type, go to service view for the service and enter the following command: Page 567 of 825 Ceragon Proprietary and Confidential...
VLAN dot1q tagging. Since more than one service point may s-tag be associated with a single interface, frames are bundle-c-tag assigned to the earliest defined service point in bundle-s-tag case of conflict. Page 568 of 825 Ceragon Proprietary and Confidential...
Page 569
Note: Multi-Carrier ABC and HSP protection are lag3 only relevant for IP-20C and IP-20C-HP units. lag4 mc-abc1 mc-abc2 mc-abc3 mc-abc4 slot Number Ethernet: 1 Radio: 2 Page 569 of 825 Ceragon Proprietary and Confidential...
Page 570
The following command adds an SAP service point with Service Point ID 10 to Service 37, with interface type bundle-s-tag. This service point is located on radio carrier 2 in an IP-20C or IP-20C-HP unit. S-VLAN 100 is classified to the service point. Page 570 of 825 Ceragon Proprietary and Confidential...
Page 571
2 port 1 sp-name pipe_dot1q_radio The following commands create a Smart Pipe service between Eth1 and radio carrier 1. This service carries S-VLANs and untagged frames between the two interfaces: Page 571 of 825 Ceragon Proprietary and Confidential...
Service 37 via Service Point 1. service[37]>sp broadcast set spid 1 state allow The following command prevents frames with a broadcast destination MAC address from ingressing Service 37 via Service Point 1. Page 572 of 825 Ceragon Proprietary and Confidential...
Number 0 – 7 If cos-mode is sp-def-cos, this is the CoS assigned to frames that pass through the service point. This decision can be overwritten on the service level. Page 573 of 825 Ceragon Proprietary and Confidential...
A service point’s egress attributes are attributes that operate upon frames ingressing via the service point. This includes VLAN preservation and marking attributes. This section includes: • Configuring VLAN and CoS Preservation (CLI) Configuring Service Bundles (CLI) • Page 574 of 825 Ceragon Proprietary and Confidential...
(see Configuring Marking (CLI)). The following command enables C-VLAN CoS preservation for Service Point 1 on Service 37: service[37]>sp cvlan-cos-preservation-mode set spid 1 mode enable Page 575 of 825 Ceragon Proprietary and Confidential...
Page 576
Configuring C-VLAN Preservation (CLI) To configure VLAN preservation for C-VLAN-tagged frames, go to service view for the service and enter the following command: service[SID]>sp cvlan-preservation-mode set spid <sp-id> mode <c-vlan preservation mode> Page 576 of 825 Ceragon Proprietary and Confidential...
<s-vlan cos preservation mode> Table 143: S-VLAN CoS Preservation CLI Parameters Parameter Input Type Permitted Description Values sp-id Number 1-32 for P2P The Service Point ID. and MP services. 1-30 for MNG services. Page 577 of 825 Ceragon Proprietary and Confidential...
Permitted Values Description sp-id Number 1-32 for P2P and MP The Service Point ID. services. 1-30 for MNG services. service-bundle-id Number 1 – 63 The service bundle assigned to the service point. Page 578 of 825 Ceragon Proprietary and Confidential...
The C-VLAN at the end of the is reserved for the default range of the VLAN Bundle. management service) The following command classifies C-VLANs 100 through 200 to Service Point 1 in Service 37: Page 579 of 825 Ceragon Proprietary and Confidential...
Permitted Values Description sp-id Number 1-32 for P2P and MP services. The Service Point ID. 1-30 for MNG services. The following command deletes Service Point 10 from Service 37: service[37]>sp delete spid 10 Page 580 of 825 Ceragon Proprietary and Confidential...
MAC address table entries. The following command limits the number of dynamic MAC address forwarding table entries for Service 10 to 128: service[10]>service mac-limit-value set 128 Page 581 of 825 Ceragon Proprietary and Confidential...
<static mac> spid <sp-id> Table 150: Adding Static Address to MAC Address Forwarding Table CLI Parameters Parameter Input Type Permitted Values Description static mac Six groups of two The MAC address. hexadecimal digits Page 582 of 825 Ceragon Proprietary and Confidential...
Page 583
The ability to flush the MAC address forwarding table per-service and per-interface is planned for future release. To perform a global flush of the MAC address forwarding table, enter the following command: root> ethernet service mac-learning-table set global-flush Page 583 of 825 Ceragon Proprietary and Confidential...
The MTU is determined by the receiving frame and editing operation on the frame. This section includes: • Configuring the S-VLAN Ethertype (CLI) • Configuring the C-VLAN Ethertype (CLI) Configuring the MRU (CLI) • Page 584 of 825 Ceragon Proprietary and Confidential...
Maximum Receive Unit (MRU). Frames that are larger than the global MRU will be discarded. For example, the following command sets the system MRU to 9612: root> ethernet generalcfg mru set size 9612 Page 585 of 825 Ceragon Proprietary and Confidential...
<slot> port <port> Use the following command to enter the view level of a group, such as a Multi- Carrier ABC group, an HSB protection group, or a LAG: root> ethernet interfaces group <group> Page 586 of 825 Ceragon Proprietary and Confidential...
2 port 2 The following prompt appears: radio [2/2]> The following command enters interface view for radio interface 1: root> ethernet interfaces radio slot 2 port 1 Page 587 of 825 Ceragon Proprietary and Confidential...
To configure an Ethernet interface’s Media Type, go to interface view for the interface and enter the following command: eth type eth [x/x]>media-type state set <media type> Table 155: Interface Media Type CLI Parameters Parameter Input Type Permitted Values Description Page 588 of 825 Ceragon Proprietary and Confidential...
Before performing this command, you must verify that the media-type attribute is set to rj45. The following command sets GbE 1 to 1000 Mbps, full duplex: eth type eth [1/1]>speed-and-duplex state set '1000fd' Page 589 of 825 Ceragon Proprietary and Confidential...
[x/x]>preamble set <preamble> Table 159: Interface Preamble CLI Parameters Parameter Input Type Permitted Values Description preamble Number 6 - 15 Sets the interface’s preamble (in bytes). Page 590 of 825 Ceragon Proprietary and Confidential...
– Statistics are represented as Layer 1 statistics, including preamble and IFG. no – Statistics are represented as Layer 2 statistics. The following commands enter interface view for GbE 1, and clear the statistics after displaying them. Page 591 of 825 Ceragon Proprietary and Confidential...
Page 592
The following commands enter interface view for radio carrier 1 in an IP-20C, IP-20C-HP, or IP-20S unit, and display statistics for the interface, without clearing the statistics. root> ethernet interfaces radio slot 2 port 1 eth type radio[2/1]>rmon statistics show clear-on-read no layer-1 no Page 592 of 825 Ceragon Proprietary and Confidential...
Even when no triggering event has taken place, the ASP mechanism sends periodic update messages indicating that no triggering event has taken place. Page 593 of 825 Ceragon Proprietary and Confidential...
Page 594
To display all automatic state propagation configurations on the unit, use the following command: root> auto-state-propagation show-config all To display the automatic state propagation configuration for a specific Ethernet port, use the following command: root> auto-state-propagation show-config eth-port eth-slot <eth-slot> eth-port <eth-port> Page 594 of 825 Ceragon Proprietary and Confidential...
Ethernet interface. csf-mode-admin Variable enable Enables or disables Client Signal Failure disable (CSF) mode. In CSF mode, the ASP mechanism does not physically shut Page 595 of 825 Ceragon Proprietary and Confidential...
The following commands bring you to interface view for radio interface 2, without clearing the statistics. root> ethernet interfaces radio slot 2 port 1 eth type radio[2/2]>rmon statistics show clear-on-read no layer-1 no Page 598 of 825 Ceragon Proprietary and Confidential...
To end the list and return to the most recent prompt, press the letter To display RX packet PMs in 15-minute intervals, go to interface view for the interface and enter the following command: Page 599 of 825 Ceragon Proprietary and Confidential...
Page 600
[x/x]> pm show tx-bcast-packets interval 15min To display TX broadcast packet PMs in 24-hour intervals, go to interface view for the interface and enter the following command: eth type eth [x/x]> pm show tx-bcast-packets interval 24hr Page 600 of 825 Ceragon Proprietary and Confidential...
The peak rate of RX multicast packets per second for the measured time interval. Average RX Multicast Packets The average rate of RX multicast packets per second for the measured time interval. Page 601 of 825 Ceragon Proprietary and Confidential...
17.5.4 Clearing Ethernet Port PMs (CLI) To clear all PMs for an Ethernet interface, go to interface view for the interface and enter the following command: eth type eth [x/x]> pm clear-all Page 602 of 825 Ceragon Proprietary and Confidential...
The classifier at the logical interface level supports the following classification methods, listed from highest to lowest priority. A higher level classification method supersedes a lower level classification method: • VLAN ID Page 603 of 825 Ceragon Proprietary and Confidential...
Number 1 – 4094 (except 4092, For double-tagged frames, the S- which is reserved for the VLAN value mapped to the CoS and default management Color values defined in the service) command. Page 604 of 825 Ceragon Proprietary and Confidential...
When 802.1p classification is set to Trust mode, the interface performs QoS and Color classification according to user-configurable tables for 802.1q UP bit (C- VLAN frames) or 802.1AD UP bit (S-VLAN frames) to CoS and Color classification. Page 605 of 825 Ceragon Proprietary and Confidential...
The following table shows the default values for the C-VLAN 802.1 UP and CFI bit classification table. Table 168: C-VLAN 802.1 UP and CFI Bit Classification Table Default Values 802.1 UP CoS (configurable) Color (configurable) Green Page 606 of 825 Ceragon Proprietary and Confidential...
The following command maps frames with an 802.1p UP bit value of 1 and a CFI bit value of 0 to CoS 1 and Green color: root> ethernet qos 802.1q-up-bits-mapping-tbl set 802.1p 1 cfi 0 cos 1 color green Page 607 of 825 Ceragon Proprietary and Confidential...
The DEI bit to be mapped. Number 0 – 7 The CoS assigned to frames with the designated UP and CFI. color Variable green The Color assigned to frames with the designated UP and CFI. yellow Page 608 of 825 Ceragon Proprietary and Confidential...
The following command enables DSCP trust mode for GbE 1: eth type eth [1/1]>classification set ip-dscp trust The following command disables DSCP trust mode for GbE 1: eth type eth [1/1]>classification set ip-dscp un-trust Page 609 of 825 Ceragon Proprietary and Confidential...
To modify the DSCP classification table, enter the following command: root> ethernet qos dscp-mapping-tbl set dscp <dscp> cos <cos> color <color> To display the DSCP classification table, enter the following command: root> ethernet qos dscp-mapping-tbl show Page 610 of 825 Ceragon Proprietary and Confidential...
[x/x]>classification set mpls <mpls> To display the trust mode for MPLS classification, go to interface view for the interface and enter the following command: eth type eth [x/x]>classification show mpls state Page 611 of 825 Ceragon Proprietary and Confidential...
To modify the MPLS EXP bit classification table, enter the following command: root> ethernet qos mpls-exp-bits-mapping-tbl set mpls-exp <mpls-exp> cos <cos> color <color> To display the MPLS EXP bit classification table, enter the following command: root> ethernet qos mpls-mapping-tbl show Page 612 of 825 Ceragon Proprietary and Confidential...
CoS Preservation and Modification on a Service Point (CLI). 18.1.9 Configuring Ingress Path Classification on a Service (CLI) For instruction on configuring ingress path classification on a service, see Configuring a Service’s CoS Mode and Default CoS (CLI). Page 613 of 825 Ceragon Proprietary and Confidential...
1 – 250 A unique ID for the rate meter (policer) profile. Number 0, or 64,000 - The Committed Information Rate (CIR) 1,000,000,000 defined for the rate meter (policer), in bits per second. Page 614 of 825 Ceragon Proprietary and Confidential...
Page 615
This profile includes the following parameters: • CIR – 64,000 bps CBS – 5 Kbytes • EIR – 64,000 bps • • EBS – 5 Kbytes • Color Blind mode Coupling Flag disabled • Page 615 of 825 Ceragon Proprietary and Confidential...
To delete a rate meter (policer) profile, use the following command: root> ethernet qos rate-meter delete profile-id <profile-id> The following command deletes Rate Meter Profile 50: root> ethernet qos rate-meter delete profile-id 50 Page 616 of 825 Ceragon Proprietary and Confidential...
[1/1]>rate-meter unicast add capability admin- state enable profile-id 1 The following command changes the rate meter (policer) profile for unicast traffic on GbE 1 to 4: eth type eth [1/1]>rate-meter unicast edit admin-state enable profile-id 4 Page 617 of 825 Ceragon Proprietary and Confidential...
To change the rate meter (policer) profile for broadcast traffic, go to interface view for the interface and enter the following command: eth type eth [x/x]>rate-meter broadcast edit admin-state <admin-state> profile-id <profile-id> Page 618 of 825 Ceragon Proprietary and Confidential...
[x/x]>rate-meter ethertype3 show configuration To delete the rate meter (policer) profile for an Ethertype, go to interface view for the interface and enter one or more of the following commands: Page 619 of 825 Ceragon Proprietary and Confidential...
When Line Compensation is 20, the rate meter operates as Layer 1. When Line Compensation is 0, the rate meter operates as Layer 2. This parameter is very important to users that want to distinguish between Layer 1 and Layer 2 traffic. Page 620 of 825 Ceragon Proprietary and Confidential...
[x/x]>rate-meter ethertype1 show statistics clear- on-read <clear-on-read> layer-1 <layer-1> eth type eth [x/x]>rate-meter ethertype2 show statistics clear- on-read <clear-on-read> layer-1 <layer-1> eth type eth [x/x]>rate-meter ethertype3 show statistics clear- on-read <clear-on-read> layer-1 <layer-1> Page 621 of 825 Ceragon Proprietary and Confidential...
802.1p UP bits and the CFI bits (for C-VLAN tags) or DEI bits (for S VLAN tags). The marking mode attribute in the service point egress attributes determines whether the frame is marked as Green or Yellow according to the calculated color. Page 622 of 825 Ceragon Proprietary and Confidential...
VLAN is also set to , re-marking is disable applied, but only according to the values defined for Green frames in the 802.1Q and 802.1AD marking tables. Page 623 of 825 Ceragon Proprietary and Confidential...
<color> 802.1p <802.1p> cfi <cfi> To display the 802.1q CoS and Color to UP and CFI bit mapping table, enter the following command in root view: root> ethernet qos 802.1q-up-bits-marking-tbl show Page 624 of 825 Ceragon Proprietary and Confidential...
Yellow Green Yellow Green Yellow Green Yellow Green Yellow Green Yellow To modify the 802.1ad CoS and Color to UP and DEI bit mapping table, enter the following command in root view: Page 625 of 825 Ceragon Proprietary and Confidential...
Yellow maximum drop is 100% Green maximum drop is 100% • Profile number 32 defines a profile in which all will be dropped. It is for internal use and should not be applied to traffic. Page 626 of 825 Ceragon Proprietary and Confidential...
Number 0 - 8192 The maximum throughput of green frames for queues with this profile, in Kbytes. When this value is reached, all green frames in the queue are dropped. Page 627 of 825 Ceragon Proprietary and Confidential...
Page 628
The edited profile has the following parameters: • green-min-threshold – 8000 Kbytes green-max-threshold – 8000 Kbytes • green-max-drop – 100% • • yellow-min-threshold – 4000 Kbytes • yellow-max-threshold –4000 Kbytes yellow-max-drop – 100% • Page 628 of 825 Ceragon Proprietary and Confidential...
2 The following command displays the WRED profile assigned to the CoS 0 queue in Service Bundle 1, on GbE 1: eth type eth [1/1]> wred show profile-id service-bundle-id 1 cos 0 Page 629 of 825 Ceragon Proprietary and Confidential...
To edit the parameters of an existing queue shaper profile, enter the following command in root view: root> ethernet qos queue-shaper-profile-tbl edit profile-id <profile-id> cir <cir> shaper-profile-name <shaper-profile- name> burst-type short Page 630 of 825 Ceragon Proprietary and Confidential...
[x/x]> queue-shaper add capability service-bundle- id <service-bundle-id> cos <cos> admin-state <admin-state> profile-id <profile-id> To change the queue shaper profile attached to a queue, go to interface view for the interface and enter the following command: Page 631 of 825 Ceragon Proprietary and Confidential...
You can configure up to 256 dual leaky bucket service bundle shaper profiles. The profiles can be configured as follows: Valid CIR values are: • 0 – 32,000,000 bps, with granularity of 16,000 bps • 32,000,000 – 1,000,000,000 bps, with granularity of 64,000 bps Page 632 of 825 Ceragon Proprietary and Confidential...
Page 633
You cannot delete a service bundle shaper profile if it is attached to a service bundle. You must first remove the profile from the service bundle. You can then delete the profile. Page 633 of 825 Ceragon Proprietary and Confidential...
To remove a service bundle shaper profile from a service bundle, go to interface view for the interface and enter the following command: eth type eth [x/x]> service-bundle-shaper delete service- bundle-id <service-bundle-id> Page 634 of 825 Ceragon Proprietary and Confidential...
Layer 1 non-effective traffic bytes on egress. The following command sets the egress line compensation value to 0 on GbE 1: eth type eth [1/1]>shaping-compensation-value set 0 Page 635 of 825 Ceragon Proprietary and Confidential...
Yellow priority profiles are defined automatically and cannot be changed or edited. The following table provides a sample of an interface priority profile. This profile is also used as the default interface priority profile. Page 636 of 825 Ceragon Proprietary and Confidential...
CoS 3 egressing the service bundle to which the profile is assigned. cos4-priority Number 1 – 4 The Green priority for the CoS 4 queue, from 4 (highest) to 1 (lowest). This Page 638 of 825 Ceragon Proprietary and Confidential...
The following command edits the profile you created in the previous command so that CoS 6 queues have a Green priority of 3 instead of 4, and a description of “c6_p3”. Page 639 of 825 Ceragon Proprietary and Confidential...
[1/1]> 18.6.5 Configuring Weighted Fair Queuing (WFQ) (CLI) This section includes: Overview of WFQ (CLI) • • Configuring a WFQ Profile (CLI) • Attaching a WFQ Profile to an Interface (CLI) Page 640 of 825 Ceragon Proprietary and Confidential...
<profile.id> cos0-weight <cos0-weight> cos1-weight <cos1- weight> cos2-weight <cos2-weight> cos3-weight <cos3-weight> cos4-weight <cos4-weight> cos5-weight <cos5-weight> cos6-weight <cos6-weight> cos7-weight <cos7-weight> To display the parameters of a WFQ profile, enter the following command in root view: Page 641 of 825 Ceragon Proprietary and Confidential...
Queue Weight (Yellow – not visible to users, and cannot be edited) The following command edits the profile you created in the previous command so that CoS 6 queues have a weight of 20 instead of 15: Page 642 of 825 Ceragon Proprietary and Confidential...
[1/1]> port-wfq set profile-id 3 The following is a sample display for the command: port-wfq show profile-id eth type eth [1/1]>port-wfq show profile-id Profile ID: 1 Queue Weight (Green) eth type eth [1/1]> Page 643 of 825 Ceragon Proprietary and Confidential...
If you enter yes, the statistics are cleared once you display them. • layer-1 Boolean – Statistics are represented as Layer 1 statistics, including preamble and IFG. • – Statistics are represented as Layer 2 statistics. Page 644 of 825 Ceragon Proprietary and Confidential...
Entering Interface View (CLI). To display whether any service bundles are configured on an interface, enter the following command in interface view: eth type eth [x/x]> eth type eth [1/2]>pm tm-queue show configuration all Page 645 of 825 Ceragon Proprietary and Confidential...
Page 646
Are you sure? (yes/no):yes eth type eth [1/1]> To display the threshold settings for a service bundle, enter the following command in interface view: eth type eth [x/x]> pm tm-queue show configuration service-bundle-id <1-6> Page 646 of 825 Ceragon Proprietary and Confidential...
Page 647
1 cos <0-7> interval <15min|24hr> For example: To display PMs for green packets passed, enter the following command in interface view: eth type eth [x/x]> pm tm-queue show counter green_packets_passed service-bundle-id 1 cos <0-7> interval <15min|24hr> Page 647 of 825 Ceragon Proprietary and Confidential...
Page 648
1 cos <0-7> interval <15min|24hr> For example: To display PMs for yellow bytes passed, enter the following command in interface view: eth type eth [x/x]> pm tm-queue show counter yellow_bytes_passed service-bundle-id 1 cos <0-7> interval <15min|24hr> Page 648 of 825 Ceragon Proprietary and Confidential...
Page 649
1 cos <0-7> interval <15min|24hr> For example: To display PMs for yellow packets dropped, enter the following command in interface view: eth type eth [x/x]> pm tm-queue show counter yellow_packets_dropped service-bundle-id 1 cos <0-7> interval <15min|24hr> Page 649 of 825 Ceragon Proprietary and Confidential...
[x/x]> tm-service-bundle clear statistics Table 207: Egress Service Bundle Level PMs CLI Parameters Parameter Input Type Permitted Values Description service-bundle-id Number 1 – 63 The service bundle for which you want to display PMs. Page 650 of 825 Ceragon Proprietary and Confidential...
Page 651
The following command displays service bundle PMs for Service Bundle 1, on GbE 1. The PMs are cleared after they are displayed. eth type eth [1/1]> tm-service-bundle show statistics service- bundle-id 1 clear-on-read yes layer-1 yes Page 651 of 825 Ceragon Proprietary and Confidential...
<control-port> vlan <vlan> To create an ABN entity consisting of a physical radio interface as the monitored interface and an interface group as the control interface, enter the following command in root view: Page 652 of 825 Ceragon Proprietary and Confidential...
Page 653
If the bandwidth is below the nominal value when the holdoff period ends, the system starts transmitting messages: root> ethernet abn abn-holdoff-set abn-name <abn-name> holdoff <holdoff-time> To clear the messages counter, enter the following command in root view: Page 653 of 825 Ceragon Proprietary and Confidential...
Number This parameter is always set to 1. control-port Number The specific Ethernet interface to which messages are transmitted when bandwidth in the monitored interface degrades below the nominal value. Page 654 of 825 Ceragon Proprietary and Confidential...
Page 655
The following command creates an ABN entity with radio interface 1 as the monitored interface and Ethernet port 1 as the control interface. It also specifies to transmit bandwidth messages on VLAN 1: Page 655 of 825 Ceragon Proprietary and Confidential...
Page 656
The following command sets the Holdoff time of ABN-1 to 15 seconds: root> ethernet abn abn-holdoff-set abn-name ABN-1 holdoff 15 The following command clears the messages counter for ABN-1: root> ethernet abn abn-entity-counter-reset abn-name ABN-1 Page 656 of 825 Ceragon Proprietary and Confidential...
<hold-multiplier> To define the interval between transmission of LLDP notifications during normal transmission periods, enter the following command in root view: root> ethernet lldp notif-interval-set notif-interval <notif- interval> Page 657 of 825 Ceragon Proprietary and Confidential...
Message Fast Tx - The interval, in seconds, at which LLDP frames are transmitted during fast transmission periods, such as when the unit detects a new neighbor. In this release, this parameter is set at 1. Page 658 of 825 Ceragon Proprietary and Confidential...
(default value). The following commands configure Ethernet port 2 to transmit and receive LLDP frames and to send a Topology Change trap to the NMS whenever the system information of its peer changes: Page 659 of 825 Ceragon Proprietary and Confidential...
System Cap Supported - A bitmap value used to identify which system • capabilities are supported on the local system, as included in TLVs transmitted by the LLDP agent. The bitmap is defined by the following parameters: Page 660 of 825 Ceragon Proprietary and Confidential...
Page 661
In this release, this parameter is always set to MAC Address. • Port ID - The port's MAC address. • Description - A text string that describes the port. In this release, this parameter is always set to ethPort. Page 661 of 825 Ceragon Proprietary and Confidential...
Page 662
The following information is displayed: • LLDP DA Index - The internal index associated with the unit's destination LLDP MAC address. • LLDP DA - The unit's destination LLDP MAC address. Page 662 of 825 Ceragon Proprietary and Confidential...
Rem System Name – The peer's system name. • Rem System Description – The peer's system description. Note: The Rem Port Description, Rem System Name, and Rem System Description fields are not used in the current version. Page 663 of 825 Ceragon Proprietary and Confidential...
Page 664
To display remote LLDP management data from a specific port, starting from a specific time, enter the following command in root view. If no time is specified, all data is displayed. root> ethernet lldp agent-remote-mng-show agent-start-time <agent-start-time> interface eth slot <slot> port <port> Page 664 of 825 Ceragon Proprietary and Confidential...
19.2.7.1 Displaying Statistics Regarding Changes in Peer Unit (CLI) To display statistics about changes reported via LLDP by the remote unit, enter the following command in root view: root> ethernet lldp statistics-scalars-show The following information is displayed: Page 665 of 825 Ceragon Proprietary and Confidential...
Page 666
LLDP header formatting problems may exist with the local LLDP agent in the sending system or that LLDPDU validation problems may exist with the local LLDP agent in the receiving system. Page 666 of 825 Ceragon Proprietary and Confidential...
Page 667
This counter is set to zero during agent initialization. This counter is incremented only once when the complete set of information is invalidated (aged out) from all related tables on a particular port. Partial ageing is not allowed. Page 667 of 825 Ceragon Proprietary and Confidential...
To change the second interface in a SyncE pipe, enter the following command in root view: root> platform sync pipe edit interface-1 pipe-id <pipe-id> interface-2-type <interface-2-type> slot <slot> port <port> To remove a SyncE pipe, enter the following command in root view: Page 668 of 825 Ceragon Proprietary and Confidential...
When configuring the Sync source, the Sync mode must be set to its default setting of automatic. To display the current Sync mode, enter the following CLI command in root view: root> platform sync mode show Page 670 of 825 Ceragon Proprietary and Confidential...
1-3 (IP-20E only) The interface to be configured as a synchronization source. priority Number 1 – 16 The priority of this synchronization source relative to other synchronization sources configured in the unit. Page 671 of 825 Ceragon Proprietary and Confidential...
<port> radio-channel <radio-channel> priority <priority> quality <quality> To remove a radio interface as a synchronization source, enter the following command in root view: root> platform sync source remove radio-interface slot <slot> port <port> radio-channel <radio-channel> Page 672 of 825 Ceragon Proprietary and Confidential...
0 20.3.3 Clearing All Sync Sources (CLI) To clear all synchronization sources that have been configured in the system, enter the following command in root view: root> platform sync source remove all Page 673 of 825 Ceragon Proprietary and Confidential...
The radio-channel configured for the synchronization source. source Variable system-clock – The interface uses the system-clock local-clock system clock as its synchronization source. local-clock – The interface uses its internal clock as its synchronization source. Page 674 of 825 Ceragon Proprietary and Confidential...
To enable SSM on a radio interface, enter the following command in root view: root> platform sync ssm admin radio-interface slot <slot> port <port> admin on To disable SSM on a radio interface, enter the following command in root view: Page 675 of 825 Ceragon Proprietary and Confidential...
The following command sets the revertive timer as 7 seconds: root> platform sync revertive-timer set rev_time 7 To display the revertive timer, enter the following command in root view: root> platform sync revertive-timer show Page 676 of 825 Ceragon Proprietary and Confidential...
To display the current synchronization configuration of the unit’s interfaces, enter the following command in root view: root> platform sync interface config show The following is a sample interface synchronization configuration display output: Page 677 of 825 Ceragon Proprietary and Confidential...
3 On the remote side of the radio link, add the radio interface facing the local device as a Sync source, with Sync Interface Priority 1. See Configuring a Radio Interface as a Synchronization Source (CLI). Page 678 of 825 Ceragon Proprietary and Confidential...
PTP packets upstream: root> platform sync ptp-tc set group id mc-abc1 direction upstream Table 218: 1588 Transparent Clock CLI Parameters Parameter Input Type Permitted Values Description slot Number port Number group Variable mc-abc1 Page 679 of 825 Ceragon Proprietary and Confidential...
Page 680
If necessary, you can use the ethernet generalcfg ptp-tc cos- command to map a different CoS value (0-7) to preserve cos value 1588 packets, but it is recommended to map 1588 packets to CoS 7. Page 680 of 825 Ceragon Proprietary and Confidential...
To display the currently configured session timeout period, enter the following command in root view: root> platform security protocols-control session inactivity- timeout show Table 219: Inactivity Timeout Period CLI Parameters Parameter Input Type Permitted Values Description Page 681 of 825 Ceragon Proprietary and Confidential...
You can configure a number of days after which a user is prevented from logging into the system if the user has not logged in for the configured number of days. You can also manually block a specific user. Page 682 of 825 Ceragon Proprietary and Confidential...
The following commands block, then unblock, a user with the user name John_Smith: root> platform security access-control user-account block user- name John_Smith block yes root> platform security access-control user-account block user- name John_Smith block no Page 683 of 825 Ceragon Proprietary and Confidential...
Input Type Permitted Values Description password aging Number 0, 20 - 90 The number of days that user passwords will remain valid from the first time the user logs into the system. Page 684 of 825 Ceragon Proprietary and Confidential...
Displaying the System Password Settings (CLI) Use the following command to display the system password settings: root> platform security access-control password show-all 21.3 Configuring Users (CLI) This section includes: User Configuration Overview (CLI) • Page 685 of 825 Ceragon Proprietary and Confidential...
Together, the system supports up to 50 user profiles. To create a new user profile with default settings, enter the following command: root> platform security access-control profile add name <profile-name> Page 686 of 825 Ceragon Proprietary and Confidential...
<profile-name> channel-type <channel-type> allowed <allowed> Table 226: User Profile Access Protocols CLI Parameters Parameter Input Type Permitted Values Description profile--name Text String Up to 49 characters The name of the user profile. Page 687 of 825 Ceragon Proprietary and Confidential...
<user-name> block <block> To change a user account's expiration date, enter the following command: root> platform security access-control user-account edit expired-date user-name <user-name> expired-date <expired-date> Page 688 of 825 Ceragon Proprietary and Confidential...
Configuring the RADIUS Server Attributes (CLI) • Viewing RADIUS Access Control and Server Attributes (CLI) • Viewing RADIUS User Permissions and Connectivity (CLI) Note: For instructions on configuring a RADIUS server, see Configuring a RADIUS Server. Page 689 of 825 Ceragon Proprietary and Confidential...
Number 1-10 The timeout (in seconds) that the agent will wait in each communication with the selected RADIUS server before retrying if no response is received. Page 690 of 825 Ceragon Proprietary and Confidential...
TDM Func Group Write level – The Write access level in the TDM functional group: None, Regular or Advanced. Eth Func Group Read level – The Read access level in the Eth functional • group: None, Regular or Advanced. Page 691 of 825 Ceragon Proprietary and Confidential...
<username> server-password <password> If the IP address family is configured to be IPv6, enter the following command in root view to configure the SFTP server parameters for the CSR file upload: Page 692 of 825 Ceragon Proprietary and Confidential...
Text String The directory path to which you are uploading the CSR. Enter the path relative to the SFTP user's home directory, not the absolute path. If the location is the home Page 693 of 825 Ceragon Proprietary and Confidential...
Table 231: Certificate Download and Install CLI Parameters Parameter Input Type Permitted Values Description server-ipv4 Dotted decimal Any valid IPv4 IP The IPv4 address of the PC or laptop format. address. you are using as the SFTP server. Page 694 of 825 Ceragon Proprietary and Confidential...
To change the protocol back to HTTP, enter the following command in root view: root> platform security url-protocol-set url-protocol http To display which protocol is currently enabled, enter the following command in root view: root> platform security url-protocol-show Page 695 of 825 Ceragon Proprietary and Confidential...
To set HTTPS normal mode, enter the following command: root> platform security https-ciphers-hardening-level-set level normal Note: The default HTTP cipher mode is normal. To display the current HTTPS cipher mode, enter the following command: root> platform security https-ciphers-hardening-level-show Page 696 of 825 Ceragon Proprietary and Confidential...
To display the result of the most recent current security log upload operation, enter the following command in root view: root> platform security file-transfer show status Page 697 of 825 Ceragon Proprietary and Confidential...
“security_log_Oct8.zip”, user name “anonymous”, and password “12345”, and initiate the upload: root> platform security file-transfer set server-path \current file-name security_log_Oct8.zip ip-address 192.168.1.80 protocol ftp username anonymous password 12345 root> platform security file-transfer operation set upload- security-log Page 698 of 825 Ceragon Proprietary and Confidential...
You can export the file using any name, then add the suffix .zip manually. For example: UnitInfo.zip If the Unit Information file is exported several times consecutively, the file itself will not be replaced. Instead, the filename will be Page 699 of 825 Ceragon Proprietary and Confidential...
Page 700
\file-name cfg_log ip-address 192.168.1.99 protocol ftp username anonymous password 12345 root> platform unit-info channel set protocol frp The following command exports the configuration log to the external server location: root> platform security configuration-log upload Page 700 of 825 Ceragon Proprietary and Confidential...
You can view a list of alarm types, edit the severity level assigned to individual alarm types, and add additional descriptive text to individual alarm types. This section includes: • Displaying Alarm Information (CLI) • Editing an Alarm Type (CLI) Page 701 of 825 Ceragon Proprietary and Confidential...
Page 702
User Guide for FibeAir® IP-20 All-Outdoor Products, CeraOS 10.5 • Setting Alarms to their Default Values (CLI) Page 702 of 825 Ceragon Proprietary and Confidential...
<alarm-id> restore default To restore the severity levels and descriptions of all alarm types to their default values, enter the following command in root view: root> platform status alarm-management set all default Page 703 of 825 Ceragon Proprietary and Confidential...
To display the current trap generation timeout, enter the following command in root view: root> platform status alarm-management alarm-stabilization-show The following command sets a trap generation timeout of 60 seconds: root> platform status alarm-management alarm-stabilization-set time 60 Page 704 of 825 Ceragon Proprietary and Confidential...
<alarm-id> display alarms, even if they are disabled. The Alarm Admin column in attributes the output displays whether the alarm or event is enabled or disabled. Page 705 of 825 Ceragon Proprietary and Confidential...
The lowest voltage during the measured period. • The highest voltage during the measured period. To display voltage PMs, enter the following command in root view: root> platform management voltage pm show pm-interval-type <all|15min|24hr> Page 706 of 825 Ceragon Proprietary and Confidential...
Page 707
The IDF column indicates whether the PM is valid: • 0 indicates a valid entry. • 1 indicates an invalid entry. This can be caused by a power surge or power failure that occurred during the interval. Page 707 of 825 Ceragon Proprietary and Confidential...
To export the unit information file you just created, enter the following command in root view: root> platform unit-info-file export To display the status of a unit information file export operation, enter the following command in root view root> platform unit-info-file status show Page 708 of 825 Ceragon Proprietary and Confidential...
\\ file-name cfg_log ip-address 192.168.1.99 protocol ftp username anonymous password 12345 root> platform unit-info channel set protocol ftp The following commands create a unit information file and export the file to the external server location: Page 709 of 825 Ceragon Proprietary and Confidential...
Page 710
The following commands create a unit information file and export the file to the external server location: root> platform unit-info-file create root> platform unit-info-file export Page 710 of 825 Ceragon Proprietary and Confidential...
By default, the Radio Logger is inactive. It should only be activated by technical support personnel, or by the customer upon request of Ceragon’s Customer Support team. Data gathered by the Radio Logger is added to the Unit Info file, which can be exported from the unit and sent to Customer Support upon their request.
To configure loopback on an Ethernet interface, go to interface view for the interface and enter the following command: eth type eth[x/x]> loopback admin <loopback-admin-state> To configure the loopback duration time, go to interface view for the interface and enter the following command: Page 712 of 825 Ceragon Proprietary and Confidential...
Page 714
MDs, but they have no functionality. The following command creates MD 5, named TR-988 with maintenance level 5. root> ethernet soam md create md-id 5 md-format none md-name TR-988 md-level 5 Page 714 of 825 Ceragon Proprietary and Confidential...
The following command creates MEG ID 1, named FR-10, with MEG level 4, assigned to Ethernet service 20. root> ethernet soam meg create meg-id 1 meg-fmt charString meg- name FR-10 meg-level 4 service-id 20 Page 715 of 825 Ceragon Proprietary and Confidential...
Page 716
To display MEG attributes, including the number of MEPS, local MEPS, and MIPs attached to the MEG, enter the following command in root view: root> ethernet soam meg attributes show meg-id <meg-id> Page 716 of 825 Ceragon Proprietary and Confidential...
MEs for which the OAM flows are not distinguishable based on the Ethernet layer encapsulation. service-id Number 0-4095 Assign the MEG to an Ethernet service. You must define the service before you configure the MEG. Page 717 of 825 Ceragon Proprietary and Confidential...
Page 718
MEPs. The system automatically defines the other MEPs you configured in the previous step as remote MEPs. See Configuring the Local MEPs (CLI). 3 Enable the Local MEPs. See Enabling Local MEPs (CLI). Page 718 of 825 Ceragon Proprietary and Confidential...
Page 719
2 mep-id 35 To display a list of local MEPs for a specific MEG, enter the following command in root view: root> ethernet soam meg local-mep show meg-id <meg-id> Page 719 of 825 Ceragon Proprietary and Confidential...
5 Table 241: MEP CLI Configuration Parameters Parameter Input Type Permitted Values Description meg-id Number 1-4294967295 Enter an ID for the MEG. mep-id Number 1-8191 A name to identify the MEG. Page 720 of 825 Ceragon Proprietary and Confidential...
Page 721
To display a list of remote MEPs (RMEPs) and their parameters per MEG and local MEP, enter the following command in root view: root> ethernet soam mep rmep list show meg-id <meg-id <meg-id> mep-id <mep-id> Page 721 of 825 Ceragon Proprietary and Confidential...
Table 242: MEP and Remote MEP Status Parameters (CLI) Parameter Definition MD Parameters MD ID The MD ID. MD Name The MD name (44 characters). MD Format The MD format (None). MD Level The maintenance level of the MD (0-7). Page 722 of 825 Ceragon Proprietary and Confidential...
Page 723
The timestamp marked by the remote MEP indicating the most recent CCM OK or failure it recorded. If none, this field indicates the amount of time, in msec intervals, since SOAM was activated. Page 723 of 825 Ceragon Proprietary and Confidential...
Page 724
MEP, along with other detailed information, enter the following command in root view: root> ethernet soam mep status general show meg-id <meg-id> mep-id <mep-id> detailed yes For example: Page 724 of 825 Ceragon Proprietary and Confidential...
Page 725
5000 To set the loopback message frame size and data pattern, enter the following command in root view: root> ethernet soam loopback data set meg-id <meg-id> mep-id <mep-id> size <size> pattern <pattern> Page 725 of 825 Ceragon Proprietary and Confidential...
Page 726
MAC address. To display the loopback attributes of a MEP, enter the following command in root view: root> ethernet soam loopback config show meg-id <meg-id> mep-id <mep-id> For example: Page 726 of 825 Ceragon Proprietary and Confidential...
The MEP ID of the interface to which you want to send the loopback. tx-num Number 0-1024 The number of loopback messages to transmit. If you enter 0, loopback will not be performed. Page 727 of 825 Ceragon Proprietary and Confidential...
1, then exit CW mode and return the interface to normal operation: root> radio slot 2 port 1 radio[2/1] modem tx-source set admin enable radio[2/1] radio[x/x] modem tx-source set mode one-tone freq- shift 5050 radio[2/1] modem tx-source set admin disable Page 728 of 825 Ceragon Proprietary and Confidential...
-45C to 60C – Temperature range for exceptional temperatures, tested successfully, with limited margins. To display the current unit temperature, see Configuring Unit Parameters. The permissible IDU humidity range is 5%RH to 100%RH. Page 730 of 825 Ceragon Proprietary and Confidential...
Web EMS page (F5) after completion of the upgrade. If pressing F5 does not help, clear the browser’s cache by pressing Ctrl+Shift+Delete. Page 731 of 825 Ceragon Proprietary and Confidential...
Two labelling formats are available for IP-20C, as shown in the following figures. Except for the interface labelling, these versions are identical. Figure 354: IP-20C Interfaces – Descriptive Labels Figure 355: IP-20C Interfaces – Letter Labels Page 732 of 825 Ceragon Proprietary and Confidential...
The voltage at the RSL interface is 1.XX where XX is the RSL level. For example: 1.59V means an RSL of -59 dBm. Note that the voltage measured at the RSL interface is not accurate and should be used only as an aid). Page 734 of 825 Ceragon Proprietary and Confidential...
User Guide for FibeAir® IP-20 All-Outdoor Products, CeraOS 10.5 23.3.7 Source Sharing IP-20C uses a TNC connector for source sharing. This connector is marked EXT/REF. Page 735 of 825 Ceragon Proprietary and Confidential...
Blinking Green – Management traffic is passing through the interface. If the MGT interface is being used for protection, the Orange LED indicates the status of the mate unit: • Off – The interface is not in an operational state (down). Page 736 of 825 Ceragon Proprietary and Confidential...
Orange -Protection is enabled, and the unit is in standby mode. • Green - Protection is enabled, the unit is in active mode, and no protection • alarms are present. • Off – Protection is not enabled. Page 737 of 825 Ceragon Proprietary and Confidential...
BNC port is not accurate and should be used only as an aid). 23.5.5 Source Sharing IP-20C-HP uses a TNC connector for source sharing. This connector is marked EXT/REF. Page 739 of 825 Ceragon Proprietary and Confidential...
Blinking Green – Management traffic is passing through the interface. If the MGT interface is being used for protection, the Orange LED indicates the status of the mate unit: • Off – The interface is not in an operational state (down). Page 740 of 825 Ceragon Proprietary and Confidential...
Orange -Protection is enabled, and the unit is in standby mode. • Green - Protection is enabled, the unit is in active mode, and no protection • alarms are present. • Off – Protection is not enabled. Page 741 of 825 Ceragon Proprietary and Confidential...
Two labelling formats are available for IP-20S, as shown in the following figures. Except for the interface labelling, these versions are identical. Figure 359: IP-20S Interfaces – Descriptive Labels Figure 360: IP-20S Interfaces – Letter Labels Page 742 of 825 Ceragon Proprietary and Confidential...
The voltage at the RSL interface is 1.XX where XX is the RSL level. For example: 1.59V means an RSL of -59 dBm. Note that the voltage measured at the RSL interface is not accurate and should be used only as an aid). Page 744 of 825 Ceragon Proprietary and Confidential...
If the MGT interface is being used for protection, the Orange LED indicates the status of the mate unit.: • Off - Admin is Disabled or no cable is connected to the interface. Page 745 of 825 Ceragon Proprietary and Confidential...
Orange -Protection is enabled, and the unit is in standby mode. Green - Protection is enabled, the unit is in active mode, and no protection • alarms are present. • Off – Protection is not enabled. Page 746 of 825 Ceragon Proprietary and Confidential...
CSFP (Dual BiDir SFP) provides Eth2 and Eth3 Port 3 (MGT): • Electric: 10/100/1000Base-T RJ-45. Management port (no traffic) Extension Port: • ◦ XPIC and HSB source sharing (planned for future release) Page 747 of 825 Ceragon Proprietary and Confidential...
CSFP (Dual BiDir SFP) provides Eth2 and Eth3 Extension Port: • ◦ XPIC and HSB (planned for future release) ◦ Direct connection to CPU by technician – see Logging in Without Knowing the IP Address Page 748 of 825 Ceragon Proprietary and Confidential...
If the port is configured for 1GE, a regular SFP module (rather than SFP+) can be used. • Extension Port: ◦ XPIC and HSB (planned for future release) ◦ Direct connection to CPU by technician – see Logging in Without Knowing the IP Address Page 749 of 825 Ceragon Proprietary and Confidential...
GbE interface is available (MGT). Figure 365: Two-Wire to PoE Port Power Adaptor 23.9.11 RSL Interface IP-20E uses a two-pin connection to measure the RSL level using standard voltmeter test leads: Figure 366: RSL Pins Page 751 of 825 Ceragon Proprietary and Confidential...
There is one Green LED to the left of the interface. The LED is for Eth1 and indicates the interface's Admin and cable connection status, and whether there is traffic on the interface: • Off - Admin is Disabled or no cable is connected to the interface. Page 752 of 825 Ceragon Proprietary and Confidential...
Green - The power is on, and the carrier is operational (up). Orange – A signal degrade condition exists on the carrier. • • Red - A loss of frame (LOF) or excessive BER condition exists on the carrier. Page 753 of 825 Ceragon Proprietary and Confidential...
Orange - The power is on, and one or more minor alarms or warnings are raised on the motherboard. • Red - The power is on, and one or more major or critical alarms are raised on the motherboard. 23.10.8 Protection LED Reserved for future use. Page 754 of 825 Ceragon Proprietary and Confidential...
Eth2/Eth3 is an SFP cage that supports regular and CSFP standards. 23.11.2 Eth1 10GE Optical Interface (SFP+) Eth1 is an SFP cage that supports the SFP+ standard. Eth1 can be configured by the user for 1GE or 10GE Ethernet traffic. Page 755 of 825 Ceragon Proprietary and Confidential...
GbE interface is available (MGT). Figure 368: Two-Wire to PoE Port Power Adaptor 23.11.5 RSL Interface IP-20V uses a two-pin connection to measure the RSL level using standard voltmeter test leads: Page 756 of 825 Ceragon Proprietary and Confidential...
Green - Admin is Enabled and a cable is connected to the interface. Blinking Green - Admin is Enabled and a cable is connected to the interface, • and there is traffic on the interface. Page 758 of 825 Ceragon Proprietary and Confidential...
Orange - The power is on, and one or more minor alarms or warnings are raised on the motherboard. • Red - The power is on, and one or more major or critical alarms are raised on the motherboard. Page 759 of 825 Ceragon Proprietary and Confidential...
• Orange - A signal degrade condition exists in at least one carrier. • • Red - A loss of frame (LOF) or excessive BER condition exists in at least one carrier. Page 761 of 825 Ceragon Proprietary and Confidential...
Indeterminate reset main-board-cold- Event Unit reset. Warning reset main-board-poe- Alarm POE input voltage is too Warning low-voltage-alarm Event Change Remote request Major was sent Event Protection switchover Major due to remote request Page 763 of 825 Ceragon Proprietary and Confidential...
Page 764
Check adjacent radio interface propagation- is triggered interface which is for failure conditions that interface-down- monitored for automatic caused automatic state alarm state propagation causes propagation. automatic shutdown of the controlled interface. Page 764 of 825 Ceragon Proprietary and Confidential...
Page 765
Loss of Carrier Major 1. Cable disconnected. 1. Check connection of cable 2. Defective cable. 2. Replace cable. ethernet-link-up Event Equipment Ethernet interface is up Warning ethernet-link-down Event Equipment Ethernet interface is Warning down Page 765 of 825 Ceragon Proprietary and Confidential...
Page 766
2. Check IF cable and replace if required. 3. Fault in RFU. 3. Replace RFU. 4. Fault in RMC (Radio Modem Card). 4. Replace RMC (Radio Modem Card). radio-link-up Event Equipment Radio interface is up Warning Page 766 of 825 Ceragon Proprietary and Confidential...
Page 767
SFP port TX power level Warning SFP transmit laser power Check laser Bias current. If it is is below the tx power is too low too low, replace SFP. level low threshold Page 767 of 825 Ceragon Proprietary and Confidential...
Page 768
Demo mode is started Warning start-by-user license-demo-stop- Event Processing Demo mode is stopped Warning by-user license-load-fail Event Equipment Activation key loading Major failure license-load- Event Equipment Activation key loaded Warning successful successfully Page 768 of 825 Ceragon Proprietary and Confidential...
Page 769
Activation key violation Major runtime-counter- sanction is enforced expired license-bad-xml- Alarm Equipment Activation key Major Essential internal Reinstall software file-alarm components are missing activation key or corrupted components are missing or corrupted. Page 769 of 825 Ceragon Proprietary and Confidential...
Page 770
1. LOC event on an 1. Check the system for local protection- Group protection Ethernet interface. failures. switchover switchover 2. Protection group 2. Check external equipment. member was disabled or pulled out of the shelf. Page 770 of 825 Ceragon Proprietary and Confidential...
Page 771
1113 software- Event Processing Missing SW Warning download-missing- components: components 1114 software- Event Processing Incomplete file set; Warning Software bundle is Get a complete software management- missing components missing components. bundle incomplete-bundle Page 771 of 825 Ceragon Proprietary and Confidential...
Page 772
Restore operation Try again operation cancelled cancelled because of user command or execution of another configuration management operation 1156 file-transfer-issued Event Processing User issued command Warning User command for transfer of configuration file Page 772 of 825 Ceragon Proprietary and Confidential...
Page 773
Note that script may assume runtime pre-existing configuration. 1166 unit-info-file- Event Processing Unit info file transfer Warning transfer-status- status: changed 1167 unit-info-file- Event Processing Unit info file creation Warning creation-status- status: changed Page 773 of 825 Ceragon Proprietary and Confidential...
Page 774
LUT file MRMC RFU file 1309 rfu-file-not-found- Alarm Equipment Radio MRMC RFU file is Major Missing radio MRMC RFU Download the specific radio alarm not found file MRMC RFU file Page 774 of 825 Ceragon Proprietary and Confidential...
Page 775
Alarm Equipment IF synthesizer is Critical 1. Extreme 1. Check installation. unlocked. temperature 2. Reset the RMC (Radio condition. Modem Card) module. 2. HW failure. 3. Replace the RMC (Radio Modem Card). Page 775 of 825 Ceragon Proprietary and Confidential...
Page 776
1697 radio-unit- Alarm Equipment Radio unit extreme Warning 1. Installation 1. Check installation extreme- temperature conditions. conditions. temperature 2. Defective RFU. 2. Verify operation as per product's specs. 3. Replace RFU. Page 776 of 825 Ceragon Proprietary and Confidential...
Page 777
3. Check IF cable and the IDU’s radio interface connectors. or the RFU. 4. Verify that the N-Type connector inner pin is not spliced. 5. Replace RMC (Radio Modem Card). 6. Replace RFU. Page 777 of 825 Ceragon Proprietary and Confidential...
Page 778
1. Check BMA connector on 2. Check BMA connector on RFU. 1704 delay-calibration- Alarm Equipment RFU delay calibration Warning Defective RFU 1. Reset the RMC (Radio failure-1 failure 1 Modem Card) / RFU. 2. Replace RFU. Page 778 of 825 Ceragon Proprietary and Confidential...
Page 780
Equipment RFU reset Major 1722 rfu-loopback-active Alarm Equipment RFU loopback is active Major User has activated RFU Disable RFU loopback. loopback. 1723 rfu-mode-changed- Event Equipment RFU mode changed to Indeterminate to-combined Combined Page 780 of 825 Ceragon Proprietary and Confidential...
Page 782
Power is enabled but 1. Check ETH cable and radio-unit-cable- open consumption is lower connectors. open than threshold. 2. Verify RFU is connected. 3. If RFU connected with optical cable, disable power interface. Page 782 of 825 Ceragon Proprietary and Confidential...
Page 783
Card was extracted from from-slot slot slot 1738 card-failure Alarm Equipment Card is in Failure state Major Card is down as a result 1. Reset Card. of card failure 2. Check if slot was disabled. Page 783 of 825 Ceragon Proprietary and Confidential...
Page 784
Event Equipment Card operational state is Indeterminate Card state was change to Down Down state 1746 card-state-is-up Event Equipment Card operational state is Indeterminate Card state was change to Up state Page 784 of 825 Ceragon Proprietary and Confidential...
Page 785
Alarm Equipment Extreme Temperature Major System Temperature not temperature in allowed range. 1757 fan-failure Alarm Equipment FAN Card is in Failure Major FAN Card is in Failure Change FAN Card state state Page 785 of 825 Ceragon Proprietary and Confidential...
Page 786
Download Main Board Major Firmware download was 1. Reset board. firmware has failed unsuccessful. 2. Download software package. 3. Try to insert another board. 1765 tcc-powerup-reset- Event Equipment Main Board was reset Warning event Page 786 of 825 Ceragon Proprietary and Confidential...
Page 787
Errors in signal from IDU 1. Check the IF cable and to XCVR. connectors. 2. Verify that the N- Type/TNC connector inner pin is not spliced. 3. Replace RMC. 4. Replace XCVR. Page 787 of 825 Ceragon Proprietary and Confidential...
Page 788
Wrong type of XCVR, the Replace the XCVR is not possible. XCVR hardware is METRO. 1776 pll-rmc Alarm Equipment RMC hardware failure. Major RMC hardware failure of Replace the RMC. the clock distributor. Page 788 of 825 Ceragon Proprietary and Confidential...
Page 789
Radio remote fault Minor indication indication (RFI) 1790 np-hw-failure Alarm Equipment Hardware failure Critical An internal hardware Replace the card or unit failure has been detected reporting the hardware failure. by the system. Page 789 of 825 Ceragon Proprietary and Confidential...
Page 790
Alarm Equipment Communication with Minor System malfunction Reset the TDM-LIC. pw-lic-comm- TDM-LIC is disrupted in disrupt Host-Card direction 2005 pwe3-pwc-s-hw- Alarm Equipment TDM-LIC hardware Major System malfunction Reset the TDM-LIC. failure failure Page 790 of 825 Ceragon Proprietary and Confidential...
Page 791
Equipment Alarm Indication Signal Major 1. Line is not properly 1. Reconnect line. (AIS) on TDM-LIC TDM connected. 2. Check line cables. port 2. External equipment 3. Check external equipment. is faulty. Page 791 of 825 Ceragon Proprietary and Confidential...
Page 792
Equipment Remote Alarm Minor 1. Line is not properly 1. Reconnect line. Indication (RAI) on connected. 2. Check line cables. TDM-LIC TDM port 2. External equipment 3. Check external equipment. is faulty. Page 792 of 825 Ceragon Proprietary and Confidential...
Page 793
Critical 1. Line is not properly 1. Reconnect line. los-alarm TDM-LIC STM1/OC3 connected. 2. Check line cables. port 2. External equipment 3. Check external equipment. is faulty. 4. Power cycle the TDM-LIC. Page 793 of 825 Ceragon Proprietary and Confidential...
Page 794
2. Reconnect line. alarm 2. SFP is not properly 3. Check line cables. installed. 4. Check external equipment. 3. SFP is faulty. 5. Power cycle the TDM-LIC. 4. External equipment is faulty Page 794 of 825 Ceragon Proprietary and Confidential...
Page 795
Loopback on TDM-LIC Warning 1. Line is not properly 1. Reconnect line. loopback-alarm VC12/VT1.5 connected. 2. Check line cables. 2. External equipment 3. Check external equipment. is faulty. 4. Power cycle the TDM-LIC. Page 795 of 825 Ceragon Proprietary and Confidential...
Page 796
Unequipped on TDM-LIC Minor 1. Line is not properly 1. Reconnect line. unequipped-alarm VC12/VT1.5 connected. 2. Check line cables. 2. External equipment 3. Check external equipment. is faulty. 4. Power cycle the TDM-LIC. Page 796 of 825 Ceragon Proprietary and Confidential...
Page 797
1. Line is not properly 1. Reconnect line. lop-alarm received on TDM-LIC connected. 2. Check line cables. VC12/VT1.5 2. External equipment 3. Check external equipment. is faulty. 4. Power cycle the TDM-LIC. Page 797 of 825 Ceragon Proprietary and Confidential...
Page 798
AIS/AIS-L) received. 2. External equipment 3. Check external equipment. is faulty. 2103 STM-1-OC-3-IN- Alarm Equipment Remote Defect Minor External equipment is Check external equipment. MSRDI Indication on Line faulty. Interface (MS-RDI/RDI- L) received. Page 798 of 825 Ceragon Proprietary and Confidential...
Page 799
LOOPBACK 2108 STM-1/OC-3- Alarm Equipment STM-1/OC-3 Channel Warning 1. Reduced capacity. 1. Check link performance. CHANNEL-1- Removed alarm (due to 2. Fading 2. Check radio alarms for REMOVED reduced radio capacity). channel. Page 799 of 825 Ceragon Proprietary and Confidential...
Page 800
2116 STM-1/OC-3- Alarm Equipment STM-1/OC-3 Channel Warning 1. Reduced capacity. 1. Check link performance. CHANNEL-5- Removed alarm (due to 2. Fading. 2. Check radio alarms for REMOVED reduced radio capacity). channel. Page 800 of 825 Ceragon Proprietary and Confidential...
Page 801
Carrier ABC group are all radio channels in Multi down. Carrier ABC group. 2. Check radio alarms for channels in Multi Carrier ABC group. 3. Check configuration of Multi Carrier ABC group. Page 801 of 825 Ceragon Proprietary and Confidential...
Page 802
2. Replace TCC. cards. 3. Replace chassis. 2206 MC-ABC-Lvds- Alarm Equipment LVDS RX Error Slot 5. Major Hardware failure 1. Replace RMC. Error-Sl5 between RMC and TCC 2. Replace TCC. cards. 3. Replace chassis. Page 802 of 825 Ceragon Proprietary and Confidential...
Page 803
RMC and TCC 2. Replace TCC. cards. 3. Replace chassis. 2219 MC-ABC-Ch-Id- Alarm Equipment Multi Carrier ABC Warning Configuration failure. Compare Channel ID Mismatch-Ch1 Channel Id Mismatch configuration with remote side. Ch1. Page 803 of 825 Ceragon Proprietary and Confidential...
Page 804
Channel Id Mismatch configuration with remote side. Ch8. 2235 MC-ABC-Ch-Id- Alarm Equipment Multi Carrier ABC Warning Admin state for channel Enable admin state for Disabled-Ch1 Channel Id Manual is down. channel. Disabled Ch1. Page 804 of 825 Ceragon Proprietary and Confidential...
Page 805
Channel Id Manual is down. channel. Disabled Ch7. 2242 MC-ABC-Ch-Id- Alarm Equipment Multi Carrier ABC Warning Admin state for channel Enable admin state for Disabled-Ch8 Channel Id Manual is down. channel. Disabled Ch8. Page 805 of 825 Ceragon Proprietary and Confidential...
Page 806
3000 chassis-reset-event Event Equipment Chassis was reset Warning User issued a command Wait until the reset cycle is to reset the chassis. ended and the system is up and running. Page 806 of 825 Ceragon Proprietary and Confidential...
Page 807
2.5Gbps mode. card that does not 1Gbps. compatibility support 2.5Gbps. 4002 slot-slotsection- Alarm Equipment Card is not functional Warning Slot is not in 10Gbps Reset chassis. 10gbps-card-not- until chassis is reset mode. functional Page 807 of 825 Ceragon Proprietary and Confidential...
Page 808
Security log upload upload-succeeded- succeeded succeeded event 5010 force-mode-alarm Alarm Equipment System is in sync force Warning User command mode state 5011 sync-quality- Event Equipment The sync-source quality Major change-event level was changed Page 808 of 825 Ceragon Proprietary and Confidential...
Page 809
1588TC is not Major System Failure Reboot the unit operational operational 5020 sync-T3-remote- Alarm Equipment T3 interface at loopback Warning loopback mode 5021 sync-T4-analog- Alarm Equipment T4 interface at loopback Warning loopback mode Page 809 of 825 Ceragon Proprietary and Confidential...
Page 810
5036 ptp-stream-state- Event Processing 1588-BC port state Warning change changed 5037 ptp-bmca-update Event Processing 1588-BC BMCA has Warning been updated. 5038 ptp-output-squelch Event Processing 1588-BC outputs are Warning squelched. Page 810 of 825 Ceragon Proprietary and Confidential...
Page 811
PRC- system clock reference. traceable source. 5047 soam-csf-ifc-down Alarm Processing Auto-state-propagation Major Remote system triggered Resolve the problem on the indication received auto-state-propagation .remote system. Page 811 of 825 Ceragon Proprietary and Confidential...
Page 812
Indeterminate initiated initiated by remote side 5107 bypass-self-test- Alarm Equipment FIPS Bypass Self-Test Critical Disk failure alarm failed 5108 post-fail-alarm Alarm Equipment Power On Self-Test Critical System failure Reboot the unit. Failed Page 812 of 825 Ceragon Proprietary and Confidential...
Page 813
1. Make sure all cables conditions-for- for MIMO conditions for MIMO. between master and slave MIMO-alarm are connected (MIMO 4x4 2. Hardware failure. only). 2. Replace faulty units and check that cables are plugged. Page 813 of 825 Ceragon Proprietary and Confidential...
Page 814
2. Radio TX and RX 3. Disable XPIC, Multi radio frequency is not and ATPC on all MIMO identical on all carriers. MIMO carriers. 3. XPIC or Multi radio or ATPC features are enabled. Page 814 of 825 Ceragon Proprietary and Confidential...
Page 815
Bring-up successfully single carrier mode (Pre-Init) 31104 AMCC-Invalid- Alarm Communications Invalid ACM Critical AMCC member have Set AMCC member to adaptive ACM- configuration been set to fixed profile ACM profiles Configuration- alarm Page 815 of 825 Ceragon Proprietary and Confidential...
Page 816
31108 AMCC-Data- Alarm Equipment MIMO insufficient Critical Data sharing cable 1. Verify Data sharing cable Sharing-cable- condition – Data sharing failure. connected. disconnected- cable failure. 2. Replace Data sharing alarm cable. Page 816 of 825 Ceragon Proprietary and Confidential...
Page 817
Alarm Equipment MIMO insufficient Critical MIMO remote failure. Handle MIMO remote failure. failure-alarm condition – Remote failure 32000 unit-mgr- Alarm Equipment Under voltage Major System Power Voltage undervoltage- lower than allowed. alarm Page 817 of 825 Ceragon Proprietary and Confidential...
Page 818
User Guide for FibeAir® IP-20 All-Outdoor Products, CeraOS 10.5 Alarm ID Name Type Group Description Severity Probable Cause Corrective Action 32001 unit-mgr- Alarm Equipment Over voltage Major System Power Voltage overvoltage-alarm higher than allowed. Page 818 of 825 Ceragon Proprietary and Confidential...
Application Specified Integrated Circuit ATPC Automatic Transmit Power Control Auxiliary Unit Baseband Baseband Switching Bit Error Rate BLSR Bidirectional Line Switch Ring BPDU Bridge Protocol Data Units Broadband Wireless Access Committed Burst Size Page 819 of 825 Ceragon Proprietary and Confidential...
Page 820
Engineering Order Wire EPROM Erasable Programmable Read Only Memory Electrostatic Discharge Electrical SFP Electrical Electrical SFP SFP+ 10G Electrical SFP SFP ETSI European Telecommunications Standards Institute Federal Communications Commission Frame Check Sequence Page 820 of 825 Ceragon Proprietary and Confidential...
Page 821
International Telecom. Union (former CCIR) ITU-T International Telecom. Union (former CCITT) Inventory Module LACP Link Aggregation Control Protocol Link Aggregation Group Local Area Network LBER Low Bit Error Rate LCAS Link Capacity Adjustment Scheme Page 821 of 825 Ceragon Proprietary and Confidential...
Page 822
Network Management System Network Time Protocol Operation Administration & Maintenance (Protocols) Outdoor Circulator Box OverHead Connections Orthogonal Mode Transducer Out of Frame OPEX Operational Expenditure PBB-TE Provider Backbone Bridge Traffic Engineering Peak Burst Rate Page 822 of 825 Ceragon Proprietary and Confidential...
Page 823
Received Signal Level RSSI Received Signal Strength Indicator RSTP Rapid Spanning Tree Protocol Service Access Point Synchronous Digital Hierarchy SDWRR Shaped Deficit Weighted Round Robin SETS Synchronous Equipment Timing Source SFTP Secure FTP Page 823 of 825 Ceragon Proprietary and Confidential...
Page 824
VCXO Voltage Controlled crystal Oscillator VLSI Very Large Scale of Integration Wide Area Network Web EMS Web-Based Element Management System Weighted Fair Queue Waveguide WRED Weighted Random Early Detection Weighted Round Robin Page 824 of 825 Ceragon Proprietary and Confidential...
Page 825
User Guide for FibeAir® IP-20 All-Outdoor Products, CeraOS 10.5 XCVR Transceiver (Transmitter/Receiver) XMTR Transmitter Crystal Oscillator Cross Polar Differentiation XPIC Cross Polarization Interference Cancellation Page 825 of 825 Ceragon Proprietary and Confidential...