Related Manuals for Danfoss APP 11-13
Summary of Contents for Danfoss APP 11-13
- Page 1 MAKING MODERN LIVING POSSIBLE Instruction Disassembling and assembling APP 11-13 and APP 16-22 ro-solutions.com...
-
Page 2: Table Of Contents
APP 11-13, Exploded view ........ -
Page 3: Disassembling
Instruction Disassembling and assembling APP 11-13 and APP 16-22 Disassembling Important: It is essential that the pump is For a better understanding of the pump, please serviced in conditions of absolute cleanliness. see exploded views on page 15 to 17. - Page 4 Instruction Disassembling and assembling APP 11-13 and APP 16-22 Mount the M8 allen screw from the tool set Wet the shaft and shaft seal with clean in the top of the shaft. (filtered) water. Carefully remove the shaft seal using the Turn pump into vertical position with shaft shaft seal extractor supplied in the toolset.
- Page 5 Instruction Disassembling and assembling APP 11-13 and APP 16-22 Using the 13 mm combination wrench, Unscrew the remaining three bolts. Turn remove all the bolts on the mounting each bolt one round at the time to make flange except the three shown in the sure that the flange is removed as straight picture in item 9.
- Page 6 Instruction Disassembling and assembling APP 11-13 and APP 16-22 Remove the retainer guide, the spring Mount the M8 eye bolt in the cylinder guide, the 7 springs and the 3 pins. barrel. Pull straight upwards. A continuous lift will elevate cylinder barrel out of housing.
-
Page 7: Assembling The Pump
Instruction Disassembling and assembling APP 11-13 and APP 16-22 Remove the remaining screws in port Carefully separate house and port flange. flange using the 13 mm combination Ensure that the guide pin for the position- wrench. ing of the house is not lost. For further disassembling of flush valve, see page 14. - Page 8 Instruction Disassembling and assembling APP 11-13 and APP 16-22 Mount the O-ring. Remember lubrication of Position housing by aligning pin hole over the O-ring with clean filtered water. guide pin. Gently press downwards. Be careful not to squeeze the O-ring. If O-ring is damaged the pump will leak.
- Page 9 Instruction Disassembling and assembling APP 11-13 and APP 16-22 Make sure there is enough free space for Unscrew M8 eye bolt. shaft beneath the housing. Minimum 100 mm (3,94 inch). Carefully lower cylinder barrel into housing. WARNING: If cylinder barrel is dropped or lowered too fast into housing, the shaft bearing might be damaged.
- Page 10 Instruction Disassembling and assembling APP 11-13 and APP 16-22 Place pistons in retainer plate and cylinder Place the guide pin in the housing. barrel. When pistons are placed, tilt retainer plate for easier placement of swash plate. If swash plate has been disassembled from mounting flange, see page 12 for assembly of swash plate.
- Page 11 Instruction Disassembling and assembling APP 11-13 and APP 16-22 Place stop for shaft seal and new shaft seal Use plastic press bush assembly tool on shaft. provided with large diameter pointing WARNING: Ensure that carbon ring is towards seal, to press seal against shoulder of pointing outwards.
-
Page 12: Disassembling And Assembling Of The Swash Plate
Instruction Disassembling and assembling APP 11-13 and APP 16-22 Disassembling and WARNING: assembling of the Make sure that the surface on the swash plate swash plate does not get any marks. Place the swash plate upside down. Change the O-rings and guide pins. -
Page 13: Disassembling And Assembling Of Cylinder Barrel/Valve Plate
Instruction Disassembling and assembling APP 11-13 and APP 16-22 Disassembling and Push a screwdriver into the hole between Remove the O-rings and backup rings. If assembling of cylinder the cylinder barrel and valve plate. Care- they have been removed they can not be... -
Page 14: Disassembling And Assembling Of The Flush Valve
Instruction Disassembling and assembling APP 11-13 and APP 16-22 Disassembling and Unscrew the flushing valve counter Remove the o-rings (green and black). assembling of the clockwise by using the pin wrench. If necessary change the valve cone, spring flush valve and plug. -
Page 15: App 11-13, Exploded View
Instruction Disassembling and assembling APP 11-13 and APP 16-22 APP 11-13, Exploded view 180R9228 / 521B1181 / DKCFN.PI.013.A2.02 / 10.2013... -
Page 16: App 16-19, Exploded View
Instruction Disassembling and assembling APP 11-13 and APP 16-22 APP 16-19, Exploded view 180R9228 / 521B1181 / DKCFN.PI.013.A2.02 / 10.2013... -
Page 17: App 22, Exploded View
Instruction Disassembling and assembling APP 11-13 and APP 16-22 APP 22, Exploded view 180R9228 / 521B1181 / DKCFN.PI.013.A2.02 / 10.2013... - Page 18 Denmark Danfoss can accept no responsibility for possible errors in catalogues, brochures and other printed material. Danfoss reserves the right to alter its products without notice. This also applies to products already on order provided that such alterations can be made without subsequential changes being necessary in specifications already agreed.