MIMAKI JV33 Series Manual

MIMAKI JV33 Series Manual

Precautions of replacing pcb

Advertisement

Quick Links

JV33 Precautions of replacing PCB

1. Overview

This document describes to determine whether a problem is caused by a damage of the PCB ASSY
related to a print head control. If the problem mentioned below occurred, it is necessary to check
condition of the damage of each part (ASSY) since the PCB could have been broken:
(1) All nozzles or nozzle line of each color would not fire. Nozzle drop out would be caused by a
certain scanning position.
(2) The printer would not be turned on. Nothing would be shown on LCD even if turning on the
power.
(3) Occurred "ERROR 07 VOLTAGE" or "ERROR 07 HEAD 0"
(4) Occurred "ERROR 09 HDC ERROR"
(5) Occurred "ERROR 200 HEAD MEMORY"
(6) Occurred "ERROR 50 MEDIA DETECT"

2. Tools to be used

Digital tester (or analog tester): it is used for measuring resistance and DC voltage
If the problem
would not be
OK
solved, please
contact
MIMAKI with
the condition
of the printer.
Problem occurred
A
4. Determining
NG
COM short circuit
(Page 2)
OK
8. Determining to
replace HDC FFC
ASSY (Page 6)
NG
Replace the
HDC FFC ASSY
Finish
1/7
MIMAKI ENGINEERING CO., LTD.
5. Checking damage
of the print heads
(Page 3)
OK
6. Checking damage
of the Main PCB
ASSY (Page 4)
OK
7. Checking damage
of the Ink slider PCB
(Page 5)
A
D900674 Ver1.1
Replace the
NG
Print heads
A
NG
Replace the
Main PCB ASSY
A
NG
Replace the
Ink slider PCB
A
D900674 Ver1.1

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the JV33 Series and is the answer not in the manual?

Questions and answers

Summary of Contents for MIMAKI JV33 Series

  • Page 1: Tools To Be Used

    MIMAKI ENGINEERING CO., LTD. JV33 Precautions of replacing PCB D900674 Ver1.1 1. Overview This document describes to determine whether a problem is caused by a damage of the PCB ASSY related to a print head control. If the problem mentioned below occurred, it is necessary to check condition of the damage of each part (ASSY) since the PCB could have been broken: (1) All nozzles or nozzle line of each color would not fire.
  • Page 2 MIMAKI ENGINEERING CO., LTD. 3. Before work Be sure to follow the instructions below to confirm that there is no residual voltage in the CAUTION: circuit board every time turning OFF the power not to limit the extent of damage.
  • Page 3 MIMAKI ENGINEERING CO., LTD. 5. Checking damage of the print heads (1) Release the lock for HDC_FFC 130/160 ASSY connected to CN1-CN4 in the Main PCB ASSY. (2) Remove HDC_FFC 130/160 ASSY. (3) Measure resistant between the test pin TP6-13 and GND in the Ink slider PCB and judge whether...
  • Page 4 MIMAKI ENGINEERING CO., LTD. 6. Checking damage of the Main PCB ASSY (1) Release the lock located both sides of the connector for HDC_FFC 130/160 ASSY connected to CN1-CN4 in the Main PCB ASSY and then remove HDC_FFC 130/160 ASSY.
  • Page 5 MIMAKI ENGINEERING CO., LTD. 7. Checking damage of the Ink slider PCB (1) Remove 6 FFC at CN1-CN6 on the Ink slider PCB. (2) Measure resistance between 3.3V pattern and GND pattern in Ink slider PCB and judge whether it is good or not with List 4.
  • Page 6 MIMAKI ENGINEERING CO., LTD. 8. Determining to replace HDC FFC 130/160 ASSY (1) Check whether the reinforcing part (light blue) of HDC FFC 130/160 ASSY connected to the Ink slider PCB is folded or not. If they are folded, please replace them since the folded FFC may cause disconnection.
  • Page 7 MIMAKI ENGINEERING CO., LTD. Date Revision history 2008/6/18 Newly issue 2008/7/2 [1] Added “ERROR 07 HEAD 0” [3] Added photo Added a step to turn off the power [7] Corrected the List 4 [8] Added a caution to handle the contact part of FFC...

Table of Contents