Delta DTE20T Instruction Sheet

Instruction Sheet
Thank you very much for choosing DTE20T/20P. Please read this instruction sheet before using your DTE20T/20P to ensure
proper operation. Keep this instruction sheet handy for quick reference.
Warning
1. Please hold the plastic terminal when installing DTE20T/20P to prevent electrostatic discharge (ESD).
2. Prevent dust or metallic debris from falling into the device and cause malfunction. DO NOT modify or uninstall
DTE20T/20P without being permitted. DO NOT use empty terminals.
3. When installing DTE20T/20P, please make sure the power of DTE main unit is switched off and insert DTE20T/20P into
the correct slot on DTE main unit.
4. Make sure you install DTE20T/20P correctly before switching on the power; otherwise serious damage may occur.
5. DO NOT touch the terminals or repair the device when the power is on; otherwise an electric shock may occur.
Functions & Electrical Specifications
Power consumption Max. 0.5W
DTE20T (4 channels of thermocouple: K, J, T, E, N, R, S, B, L, U, TXK
Input sensor
DTE20P (3 channels of platinum RTD): Pt100, JPt100, Ni120, Cu50
Sampling cycle Thermocouple or platinum RTD: 1.0 second (all inputs)
Terminal connection Can only be inserted into INB slot on DTE10T or DTE10P main unit
The sensor slot (INA/INB) only accepts the same input type. For example, if you select DTE20T as
accessory, you can only use it on DTE10T main unit. If you select DTE20P as accessory, you can only use it
on DTE10P main unit.
The accessories using for the DTE main unit, please download the DTE10P and DTE10T main unit
operating manual for reference on Delta website.
How to Install
1 Remove all the terminal 2 Uncover the panel. Make
blocks on the panel. sure which slot is the
correct one and insert
DTE-20T/20P into the
slot.
DTE Accessory
3 Cover up the panel. 4 Insert the terminal blocks
back
非常感謝您選用台達產品，請在使用前，詳細閱讀本使用說明書，並將手冊放置於易拿處以便參考。
注意事項
1. 安裝時，請握住塑膠端子部分，防止靜電破壞(ESD)。
2. 如果有塵土或金屬殘渣掉入機身，可能會造成誤運行。請勿修改或擅自拆卸電路板。空餘端子請勿使用。
3. 安裝配件電路板時，請先確認主機已斷電，並確認該配件正確的插槽位置。
4. 上電前請確認裝配是否正確及配件電路板到定位，否則可能造成嚴重損壞。
5. 上電時請勿接觸機體端子或進行維修，否則可能遭致電擊。
功能與電氣規格
Max. 0.5W
電源消耗功率
DTE20T（4 通道熱電偶對） ：K, J, T, E, N, R, S, B, L, U, TXK
輸入感測器
DTE20P（3 通道白金測溫電阻） ：Pt100, JPt100, Ni120, Cu50
取樣頻率 熱電偶對或白金測溫電阻：1.0 秒（所有輸入）
僅可插入 DTE10T 或 DTE10P 主機的 INB 插槽
端子連接功能
感測器插槽(INA/INB)只能接受相同的輸入形式，例如若配件選擇為 DTE20T，則只能與主機 DTE10T 搭配
使用。配件選擇為 DTE20P，則只能與主機 DTE10P 搭配使用。
本配件為配合 DTE 主機使用，請於台達網站下載 DTE10P 及 DTE10T 主機操作手冊參考使用。
安裝方式及步驟
1 移除面板上所有脫落式端 2 掀開面板，確認該配件正
子 確的插槽位置 ， 插入電路板
至定位。
配件安裝手冊
3 蓋回面板至定位 4 裝回脫落式端子至定位