Laser Rangefinder; Bix Technology; Lrf Preview; System Settings - ATN BinoX 4K 4-16x Manual

LASER RANGEFINDER

TARGET DISTANCE
show the distance in the upper left corner. The device will exit measurement
mode automatically.
Unit of measurement can be selected for the device in System Settings →
Settings → Units. Your laser rangefinder also has two operation modes, Stan-
dard mode and Fog mode, for adverse environmental conditions, which can
be selected in System Settings → Settings → WiFi and Bluetooth → Range-
finder Mode.

BIX TECHNOLOGY

If you have an ATN Smart HD scope and would like to use your ATN Bi-
noX 4K to transmit the range data to your ATN Smart HD scope via Bluetooth.
Please follow the next few steps in order to accomplish this.
Make sure you have activated the advanced settings in your BinoX 4K.
• Open the shortcut Carousel → System Settings → Settings → WiFi &
Bluetooth → Broadcast LRF.
• Select Broadcast LRF and switch it "ON".
Turn on your ATN Smart HD scope. Make sure you have activated the ad-
vanced settings in the shortcut Carousel.
16
W h i l e r e c o r d i n g t h e
Counter widget appears.
In order to Start recording
video, while on the Home-
screen, press the RIGHT
button to activate vid-
eo recording. Press the
RIGHT button
more to Stop recording
video.
The new 4K Sensor was incorporated
for better visibility and crisper images,
but we didn't stop there. We integrated
a Laser Rangefin der, so you now have
the ultimate binocular package that has
everything you want. Not only do you
have the ability to see both day and
night at your fingertips, but
you now have the ability to
range your target with ab-
solute accuracy for dope
hold over or know how far
you need to trek to your
next waypoint.
To measure the distance
to a target using the laser
rangefinder short press
the POWER button. The
rangefinder will take sever-
al measurements and will
• Open the shortcut Carousel → System Settings → Settings → WiFi &
Bluetooth → BinoX LRF.
• Select BinoX LRF and switch it "ON".
Now take your ATN BinoX 4K and Short Press the power button. You should
see the Rangefinding reticle appear. Once the BinoX 4K ranges the target, the
range data will automatically be transfered to your ATN Smart HD scope. If you
have the Ballistic Calculator turned on and the Ballistic profile has been setup,
your POA will change based on the reading the ATN Smart HD scope receives
once
from the ATN BinoX 4K.

LRF PREVIEW

If you would like to have a reference point of where the Laser Range Find-
er is collimated too. You can turn on the LRF Preview. This will turn on a red
square box in your BinoX 4T FOV as a reference point. In order to turn the LRF
preview on, go to the Shortcut Carousel → System Settings → Display → LRF
Preview and turn it ON.
Once it is turned on, you will see a red box on your Homescreen, providing
you with a LRF reference point. This does not turn the LRF on or Range the
target continuously. In order to turn the LRF function on with preview activated,
you still need to press the Power button once.
SYS T E M S E T T I N G S

NIGHT VISION

LIGHT SENSITIVITY
There are two options
for Light Sensitivity; Low or
High. On the Low setting,
you will get 30 fps. On the
High setting, you will get 15
fps. Your selection will de-
pend on the amount of am-
bient light needed for opti-
mal performance.

PHOTO/VIDEO

MICROPHONE — sound
recording (ON/OFF).
VIDEO QUALITY — can
be 1080p @ 30/60/120 fps.
The ATN BinoX 4K is ca-
pable of recording in day
mode at 120 fps. This fea-
ture allows for post produc-
tion editing for slow motion
purposes.
Please note that the 120
fps mode is available in daytime setting only and it does not improve your im-
age quality. It should only be used if you plan on doing post production video
editing.
17