Table of Contents
Related Manuals for Access ROYALE
Summary of Contents for Access ROYALE
- Page 1 INSTALLATION & OPERATING INSTRUCTIONS W H I R L P O O L B AT H T U B S MODEL ROYALE Costco Model # 1075666/1075667 ACCESS TUBS 5701 NW 35 Avenue Miami, FL 33142 Phone 877-249-2388 Fax 866-560-1060 info@accesstub.com...
-
Page 3: Planning The Installation
* Run pump only when water in tub is two inches over jets. The plumbing system on all ACCESS Tubs meets ASME, and UL standards. Any modifications to the plumbing system, including the pump, will void the warranty and approvals. -
Page 4: Read And Follow All Instructions
ACCESS Tubs will not be held responsible for tub damage or color compatibility problems after whirlpool is installed. ACCESS Tubs will not be held responsible for cost of installation or repair if an incorrect tub is installed. Read instructions before starting installation. -
Page 5: General Notes
Rough-in wiring to equipment on a Ground-Fault Circuit Interrupter (GFCI). The GFCI circuit breaker must not supply any other devices or circuits. An access panel must be installed to permit pump service. INSTALLATION... - Page 6 The Royale bathtub combines the curvy elegance of a contemporary tub with the classical flair of a traditional tub. The Royale features a spacious interior and a subtly contoured back rest that maximizes comfort and relaxation. The uniquely raised crowning along the top is the Royale’s distinguishing feature and a perfect addition to any bathroom.
-
Page 7: Installation
INSTALLATION PREPARATION INSTALL DRAIN HARDWARE Clean, level and prepare the floor for installation. Apply a bead of clear silicone or plumbers putty around the Drain Body and pass it through the drain hole (figure Place the unit in the exact installed position on the floor and trace the outline of the bath with a pencil or any erasable marking (figure 1). - Page 8 INSTALLATION CONTINUED...
- Page 9 (figure 6). tub while inspecting the waste connections below the floor for leaks. Access from below will be necessary for Then apply a bead of tub and tile caulk around the edge this step (figure 8).
- Page 10 Before finishing with your choice of material, make sure what is necessary. Provide supply pipe, rough-in waste and access entries are available to the pump, bath waste, and vent per code. plumbing fixtures. Finish as desired and seal around tub, preferably with silicone.
- Page 11 INSTALLATION CONTINUED ACCESS TUBS ROYALE DUAL SYSTEMS CONTROLS 1. Whirlpool Pressure Adjustor 4. Bubble Massage On/Off Button Use to adjust the strength and pressure of the Press once to turn on the air pump and activate whirlpool jets. the Bubble Massage air jets. Press again to turn off pump and deactivate air jets.
- Page 12 INSTALLATION CONTINUED For any maintenance or repair the Royale shell can be removed by flipping the tub over, lo- cating and removing the 4 plastic nubs and loosening the securing screws underneith. Then the entire shell can easily be removed.
-
Page 13: User Maintenance
USER SHOULD periodically flush operating system (not to exceed 90 days). As a minimum, shall consist of filling and running system and draining. Access Tubs recommends flushing with a mild solution of water and sanitizer such as chlorine or other commercially available whirlpool bath flushing products. - Page 14 Written notice of any malfunction or defect must be given within ten BATH SHELL: Access Tubs warrants its bath shells against loss of (10) days of the time it is discovered, to Access Tubs, 5701 NW 35th water through the fiberglass laminate of the tub body as a result of a Avenue, Miami, Florida 33142.
-
Page 15: Installer Information
NOTES INSTALLER INFORMATION DATE OF INSTALL: INSTALLER’S NAME: PLUMBER: CONTRACTOR: LICENSE #:... - Page 17 Record the numbers here for handy reference: Model No. Serial No. Date of Purchase M a d e i n Manufactured by Access Tubs A Division of Spa World Corp. 5701 NW 35th Avenue U S A Miami, Florida 33142 Ph: 877.249.2388 • Fax: 866.560.1060...